Search NASA⌕ Search

Engineering topics

Pickel, Deanna L

Publications and source records attributed to Pickel, Deanna L.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Structural Evolution of Polylactide Molecular Bottlebrushes: Kinetics Study by Size Exclusion Chromatography, Small Angle Neutron Scattering and Simulations

Structural evolution from poly(lactide) (PLA) macromonomer to resultant PLA molecular bottlebrush during ring opening metathesis polymerization (ROMP) was investigated for the first time by combining size exclusion chromatography (SEC), small-angle neutron scattering (SANS) and coarse-grained molecular dynamics (CG-MD) simulations. Multiple aliquots were collected at various reaction times during ROMP, and subsequently analyzed by SEC and SANS. The two complementary techniques enable the understanding of systematic changes in conversion, molecular weight and dispersity as well as structural details of PLA molecular bottlebrushes. CG-MD simulation not only predicts the experimental observations, but it also provides further insight into the analysis and interpretation of data obtained in SEC and SANS experiments. We find that PLA molecular bottlebrushes undergo three conformational transitions with increasing conversion (i.e., increasing the backbone length): (1) from an elongated to a globular shape due to longer side chain at lower conversion, (2) from a globular to an elongated shape at intermediate conversion caused by excluded volume of PLA side chain, and (3) the saturation of contour length at higher conversion due to chain transfer reactions.

Pickel, Deanna L↗
DOE OSTI2012

Ternary behavior and systematic nanoscale manipulation of domain structures in P3HT/PCBM/P3HT-b-PEO films

Nanophase separation plays a critical role in the performance of donor acceptor based organic photovoltaic (OPV) devices. Although post-fabrication annealing is often used to enhance OPV efficiency, the ability to exert precise control over phase separated domains and connectivity remains elusive. In this work, we use a diblock copolymer to systematically manipulate the domain sizes of an organic solar cell active layer at the nanoscale. More specifically, a poly(3-hexylthiophene)-bpoly( ethylene oxide) (P3HT-b-PEO) diblock copolymer with a low polydispersity index (PDI 1.3) is added to a binary blend of P3HT and 6,6-phenyl C61-butyric acid methyl ester (PCBM) at different concentrations (0 20 wt%). Energy-filtered TEM (EFTEM) results suggest systematic changes of P3HT distribution as a function of block copolymer compatibilizer concentration and thermal annealing. X-ray scattering and microscopy techniques are used to show that prior to annealing, active layer domain sizes do not change substantially as compatibilizer is added; however after thermal annealing, the domain sizes are significantly reduced as the amount of P3HT-b-PEO compatibilizer increases. The impact of compatibilizer is further rationalized through quantum density functional theory calculations. Overall, this work demonstrates the possibility of block copolymers to systematically manipulate the nanoscale domain-structure of blends used for organic photovoltaic devices. Furthermore, if coupled with efficient charge transport and collection (through judicious choice of block copolymer type and composition), this approach may contribute to further optimization of OPV devices.

14 SOLAR ENERGY↗
DOE OSTI2012

Enhanced control of end-group composition in poly(3-hexylthiophene)s prepared by GRIM

The ability to prepare well-defined semiconducting polymers is essential for understanding the link between structure and function in organic photovoltaic devices. A general method for enhanced control of the degree of functionality of end-functionalized poly(3-hexylthiophene)s (P3HT) prepared by Grignard Metathesis (GRIM) polymerization has been developed. In the absence of additives, the degree of functionality of end-functional P3HTs prepared by quenching of the GRIM polymerization with a Grignard reagent is dependent on the Grignard reagent utilized. In this study, additives such as styrene and 1-pentene are shown to alter the end-group composition of tolyl-functionalized P3HTs as determined by MALDI-TOF MS. In particular, when quenching the GRIM polymerization with tolylmagnesium bromide a modest decrease in the difunctional product is observed, and the yield of the monofunctional product increases significantly. Temperature and lithium chloride (LiCl) addition also play impactful roles. Monofunctional P3HT is found to be the major product (65%) when the functionalization is done in the presence of LiCl and styrene at 0oC, whereas in the absence of additives the monofunctional product is present at only 20%.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Turning Renewable Resources into Recyclable Polymer: Development of Lignin-Based Thermoplastic

Productive uses of lignin, the third most abundant natural polymer, have been sought for decades. One especially attractive possibility is that of developing value-added products including thermoplastics based on lignin. This possibility warrants special attention due to growth of the modern biofuel industries. However, the polydisperse molecular weight and hyper-branched structure of lignin has hindered the creation of high-performance biopolymers. Here, we report the preparation and characterization of novel lignin-based, partially carbon-neutral thermoplastics. We first altered the molecular weight of lignin, either by fractionation with methanol, or by formaldehyde crosslinking. A crosslinking of lignin increases the molecular weight, exhibiting Mn = 31000 g/mol, whereas that of native lignin is 1840 g/mol. Tuning the molecular weight of lignin enabled successful preparation of novel lignin-derived thermoplastics, when coupled with telechelic polybutadiene soft-segments at proper feed ratios. Characteristic to thermoplastic rubbers, free-standing films of the resulting copolymers exhibit two-phase morphology and associated relaxations in the dynamic mechanical loss spectrum. To our knowledge this article is the first report to demonstrate phase immiscibility, melt-processibility, and biphasic morphology of soft and hard segments in a lignin-based copolymer for all feed ratios of two macromolecular components. The use of higher molecular weight lignin enhanced the resulting shear modulus due to efficient network formation of telechelic polybutadiene bridges. The storage modulus in the rubbery plateau region increased with increasing lignin content. The successful synthesis of novel lignin-based thermoplastics will open a new pathway to biomass utilization and will help conserve petrochemicals.

Lignin↗