Engineering topics

Pierce, F. J.

Publications and source records attributed to Pierce, F. J..

13 records

NASA NTRS1992

The development of a turbulent junction vortex system

The growth and development of a horseshoe vortex system in an incompressible, three-dimensional turbulent junction flow were investigated experimentally. A streamlined cylinder mounted with its axis normal to a flat surface was used to generate the junction vortex flow. The flow environment was characterized by a body Reynolds number of 183,000, based on the leading edge diameter of the streamlined cylinder. The study included surface flow visualizations, surface pressure measurements, and mean flow measurements of total pressure, static pressure, and velocity distributions in three planes around the base of the streamlined cylinder, and in two planes in the wake flow. Some characterizations of vortex properties based on the measured mean cross-flow velocity components are presented. The results show the presence of a single large, dominant vortex, with strong evidence of a very small corner vortex in the junction between the cylinder and the flat surface. The center of the dominant vortex drifts away from both the body and the flat surface as the flow develops along and downstream of the body. The growth and development of the core of the large, dominant vortex are documented.

Pierce, F. J.↗

NASA NTRS1991

Standard test case for a low-speed, turbulent junction vortex flow

The mean flow structure upstream, around within, and in the near wake of a turbulent junction or horseshoe vortex is reported for an incompressible subsonic flow. Measurements of the primitive variables of velocity and pressure are reported on all surfaces bounding the region of the vortex flow and on three transverse and one streamwise plane within the flowfield itself for comparisons between the measured and any calculated flow variables. Detailed surface flow visualizations and some direct force measurements of surface shear stress are also available. The data is a highly detailed, coherent, self-consistent set offered to the computational fluid mechanics community as a standard test case for the evaluation of the capability of numerical solvers intended for predicting the flowfield in such a complex, separated, three-dimensional turbulent flow. This data base is available for copying to user supplied tapes or for transmission via BITNET, as well as in two National Technical Information Service (NTIS) reports.

Pierce, F. J.↗

NASA NTRS1990

The growth and development of a turbulent junction vortex system

The growth and development of a vortex system in an incompressible three-dimensional flow generated by a streamlined cylinder mounted with its axis normal to a flat surface was investigated using data from surface flow visualizations, surface pressure measurements, and mean flow measurements. The results from velocity measurements revealed the presence of a single large dominant vortex and a small vortex in the junction between the cylinder and the flat surface. This second vortex is tentatively identified as being connected with a corner separation occurring just downstream of the body at its thickest cross section. It is shown that, as the principal horseshoe vortex develops downstream, the strength of the vortex decreases, while its length scale increases.

Pierce, F. J.↗

NASA NTRS1989

The pattern of secondary root formation in curving roots of Arabidopsis thaliana (L.) Heynh

A gravitational stimulus was used to induce the curvature of the main root of Arabidopsis thaliana. The number of secondary roots increased on the convex side and decreased on the concave side of any curved main root axes in comparison with straight roots used as the control. The same phenomenon was observed with the curved main roots of plants grown on a clinostat and of mutant plants exhibiting random root orientation. The data suggest that the pattern of lateral root formation is associated with curvature but is independent of the environmental stimuli used to induce curvature.

Non-NASA Center↗

NASA NTRS1988

The mean flow structure around and within a turbulent junction or horseshoe vortex. I - The upstream and surrounding three-dimensional boundary layer

An experimental study of the mean flow structure upstream, around, and in a turbulent junction or horseshoe vortex is presented for the case of an incompressible subsonic flow. Mean velocity field and turbulent kinetic energy field measurements (obtained with hot film anemometry) and local wall shear stress measurements are used to monitor the upstream and surrounding three-dimensional turbulent boundary layer-like flow away from separation. Freestream or edge velocity and floor static pressure results are reported.

Menna, J. D.↗

NASA NTRS1988

The mean flow structure around and within a turbulent junction or horseshoe vortex. II - The separated and junction vortex flow

Five-hole probe measurements of the flow through the separation region and in the vortex system of an incompressible subsonic flow around and within a turbulent junction or horseshoe vortex are reported. Mean velocity, static pressure, and total pressure results are presented. The streamwise vorticity field is obtained from the measured velocity field. Flow visualization results for the floor and cylinder surface agree well with the flow field data.

Pierce, F. J.↗

NASA NTRS1985

A three-dimensional turbulent separated flow and related mesurements

The applicability of and the limits on the applicability of 11 near wall similarity laws characterizing three-dimensional turbulent boundary layer flows were determined. A direct force sensing local wall shear stress meter was used in both pressure-driven and shear-driven three-dimensional turbulent boundary layers, together with extensive mean velocity field and wall pressure field data. This resulted in a relatively large number of graphical comparisons of the predictive ability of 10 of these 11 similarity models relative to measured data over a wide range of flow conditions. Documentation of a complex, separated three-dimensional turbulent flow as a standard test case for evaluating the predictive ability of numerical codes solving such flows is presented.

Pierce, F. J.↗

NASA NTRS1982

Direct force wall shear measurements in pressure-driven three-dimensional turbulent boundary layers

Unique, simultaneous direct measurements of the magnitude and direction of the local wall shear stress in a pressure-driven three-dimensional turbulent boundary layer are presented. The flow is also described with an oil streak wall flow pattern, a map of the wall shear stress-wall pressure gradient orientations, a comparison of the wall shear stress directions relative to the directions of the nearest wall velocity as measured with a typical, small boundary layer directionally sensitive claw probe, as well as limiting wall streamline directions from the oil streak patterns, and a comparison of the freestream streamlines and the wall flow streamlines. A review of corrections for direct force sensing shear meters for two-dimensional flows is presented with a brief discussion of their applicability to three-dimensional devices.

Mcallister, J. E.↗

NASA NTRS1982

Preston tube calibrations and direct force floating element measurements in a two-dimensional turbulent boundary layer

Preston tubes provide a convenient means of estimating local wall shear stress. Practical difficulties arise from a lack of calibration data obtained in turbulent boundary layer flows and from the wide choice of calibration equations available mainly from pipe flow calibrations. The results of an experimental study comparing a large number of direct force local wall shear stress measurements in a near-zero pressure gradient two-dimensional turbulent boundary layer flow are presented. The results indicate that there is consistent and excellent agreement between the Patel intermediate calibration formula and the direct force measurements. Typical differences among the direct force measurements and several other proposed calibration equations are also shown.

Mcallister, J. E.↗

NASA NTRS1982

Near-wall similarity in three-dimensional turbulent boundary layers. I - Model review. II - Pressure-driven flow results

Eleven proposed models for near-wall similarity for three-dimensional turbulent boundary layer flows are reviewed. Six of these models are comparatively simple scalar models and five are more complex and/or two-component vector models. Ten of the models can be tested as to their validity or predictive capability with the aid of measured mean velocity field, wall pressure field, and direct wall shear stress field (magnitude and direction) data. One of the models cannot be tested owing to its dependence on two parameters that are at present extremely difficult (if not impossible) to measure. Ten three-dimensional near-wall similarity models are then evaluated with direct wall shear, velocity field, and pressure gradient data from a three-dimensional pressure-driven boundary layer flow. In a primary focus of the interval where y+ is between 50 and 300, graphical results suggest that six simpler models and the freestream component of one complex model are adequate for profiles with monotone increasing skew up to about 15 deg.

Pierce, F. J.↗

NASA NTRS1982

Near-wall similarity in the three-dimensional turbulent boundary layers. III - Shear-driven flow results

Ten of eleven proposed three-dimensional similarity models identified in the literature are evaluated with direct wall shear, velocity field, and pressure gradient data from a three-dimensional shear-driven boundary layer flow. Results define an upper limit on velocity vector skewing for each model's predictive ability. When combined with earlier results for pressure-driven flows, each model's predictive ability with and without pressure gradients is summarized. The utility of some two-dimensional type indirect wall shear measurement methods and wall shear inference methods from near-wall velocity measurements for three-dimensional flows is also discussed.

Pierce, F. J.↗

NASA NTRS1982

Measurements in a pressure-driven and a shear-driven three-dimensional turbulent boundary layer

Results of mean velocity field, wall static pressure field and simultaneous, direct force measurements of the local wall shear stress magnitude and direction are reported for a pressure-driven and a shear-driven three-dimensional turbulent boundary layer. These data, particularly the direct force local wall shear data, were obtained to test the validity of several of the near-wall similarity models proposed in the literature for such flows.

Pierce, F. J.↗

NASA NTRS1980

Near-wall similarity in a pressure-driven three-dimensional turbulent boundary layer

Mean velocity, measured wall pressure and wall shear stress fields were made in a three dimensional pressure-driven turbulent boundary layer created by a cylinder with trailing edge placed normal to a flat plate floor. The direct force wall shear stress measurements were made with floating element direct force sensing shear meter that responded to both the magnitude and direction of the local wall shear stress. The ability of 10 near wall similarity models to describe the near wall velocity field for the measured flow under a wide range of skewing conditions and a variety of pressure gradient and wall shear vector orientations was used.

Pierce, F. J.↗