Search NASA⌕ Search

Engineering topics

Pilgrim, Corey David

Publications and source records attributed to Pilgrim, Corey David.

Intrinsic Bonding and Reactivity of Actinide Clusters Poster

The effect of electronic structure on chemical bonding and reactivity is one of the most important questions in the field of chemistry. Insight into chemical bond formation involving elements that contain f electrons (i.e., the lanthanides and actinides) is critical for solving specific technical challenges, such as development of advanced nuclear fuel cycles and efficient rare earth separations, as well as a broader understanding of bonding across the entire periodic table. The primary technique for studying the fundamentals of lanthanide and actinide bonding is crystallization of metal-ligand compounds followed by structural determination with X-rays and comparison to theory with computational chemistry. While this procedure has yielded significant insights for a wide variety of elements, it is challenging to apply to the heavier trans-uranic actinides such as berkelium and californium because of limited material availability, significant radioactivity, and poorly understood chemical reactivity of these elements. We hypothesize that by forming actinide-ligand clusters in a mass spectrometer and probing their reactivity in the gas-phase, many of the challenges associated with studying the heavier trans-uranic elements can be circumvented. This project will develop a capability to address a wide range of actinide bonding and reactivity phenomena, increasing Idaho National Laboratory’s capability to address fundamental questions at the forefront of heavy element chemical and molecular science.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparison of Gas Phase Fragmentation Behaviors of Nuclear Fuel Cycle Ligands in Lanthanide and Americium Metal Ligand Nitrate Clusters

Introduction (120 words): Transport of metal ions across the aqueous-organic phase boundary is an essential step in a hydrometallurgical nuclear fuel reprocessing strategy. The study of transport agents for nuclear fuel elements is imperative to guide the design of ligands that boost the separation efficiency of the recovery process from fission products. However, limited studies have been made on the chemistry of these transport agents when complexing with transuranic elements in gas-phase where all surrounding factors are essentially excluded. This work investigates the reagent ligand complexations to transuranic and other metals and their dissociations in the gas phase. Comparisons are made between 4f and 5f elements and between ligands. Methods (120 words): (N,N-diisobutylcarbamoylmethyl)phenyloctylphosphine oxide (CMPO) and N,N,N',N'-tetraoctyldiglycolamide (TODGA) have been selected to complex with metal nitrates. The actinide americium and lanthanides neodymium, samarium, and europium were investigated as part of this work. The lanthanides were selected to act as size and electron configuration analogues of the minor actinides. Metal complexes with two ligands and two nitrates ([M(NO3)2(CMPO)2]+, for example) are studied in Bruker micrOTOF-Q II mass spectrometer equipped with collision-induced dissociation capability. The comparisons of the mass spectra are made in groups of homogenous ligands and mixed TODGA-CMPO ligands clusters. Comparisons are also made based on the complexed metals (Am and lanthanides). Preliminary data (300 words): Collision-induced dissociation mass spectrometry data are collected on two ligands complexed with metal nitrates where the two ligands are homogenous, with (CMPO)2 or (TODGA)2, or heterogeneous, with (TODGA)(CMPO). Several fragmentation patterns are observed among complexes with the CMPO ligand whereas the TODGA ligand commonly dissociates intact from the complex. Most of the metal complexes exhibit similar fragmentation patterns, but there are a few notable deviations in fragmentation patterns between the Am and Ln-bearing complexes. For the [M(CMPO)2(NO3)2]+ complexes, the initial loss of nitrate in the form of nitric acid is observed in all four complexes. However, [Am(CMPO)2(NO3)2]+ exhibits an additional fragmentation not found in the lanthanide complexes. Also, a significantly different ratio of the second nitric acid loss is found in the Am complex. These deviations may indicate the different interaction behaviors between actinides and lanthanides. The [M(TODGA)2(NO3)2]+ complexes exhibit the fragmentation as the loss of one TODGA ligand as an intact form and the loss of nitrate as nitric acid. The Am complex exhibits an additional fragmentation after losing the TOGDA ligand, which is not observed among the Ln complexes. The heterogeneous [M(TODGA)(CMPO)(NO3)2]+ complexes exhibit both similarities and differences between the Am and Ln complexes. For example, the heterogenous Am complex does not exhibit the loss of an intact TODGA ligand while all three Ln complexes do. This indicates that TODGA may bind more strongly to Am than Ln. Additionally, the intensity of the loss of CMPO ligand (as partially or whole) is found to be significantly larger than that of the loss of TODGA (as partially of whole) indicating that TODGA is bound to the metal significantly stronger than CMPO. Planned computational analysis will help understand the deviation in fragmentation behaviors between americium and lanthanide metal centers, or between TODGA and CMPO ligands. Novel aspect (20 words): Gas-phase actinide and lanthanide complex formation and fragmentation provide insight into the coordination environment differences of f-element metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparison of Gas Phase Fragmentation Behaviors of Nuclear Fuel Cycle Ligands in Lanthanide and Americium Metal Ligand Nitrate Clusters

Title (20 word): Comparison of Gas Phase Fragmentation Behaviors of Nuclear Fuel Cycle Ligands in Lanthanide and Americium Metal Ligand Nitrate Clusters Introduction (120 words): Transport of metal ions across the aqueous-organic phase boundary is an essential step in a hydrometallurgical nuclear fuel reprocessing strategy. The study of transport agents for nuclear fuel elements is imperative to guide the design of ligands that boost the separation efficiency of the recovery process from fission products. However, limited studies have been made on the chemistry of these transport agents when complexing with transuranic elements in gas-phase where all surrounding factors are essentially excluded. This work investigates the reagent ligand complexations to transuranic and other metals and their dissociations in the gas phase. Comparisons are made between 4f and 5f elements and between ligands. Methods (120 words): (N,N-diisobutylcarbamoylmethyl)phenyloctylphosphine oxide (CMPO) and N,N,N',N'-tetraoctyldiglycolamide (TODGA) have been selected to complex with metal nitrates. The actinide americium and lanthanides neodymium, samarium, and europium were investigated as part of this work. The lanthanides were selected to act as size and electron configuration analogues of the minor actinides. Metal complexes with two ligands and two nitrates ([M(NO3)2(CMPO)2]+, for example) are studied in Bruker micrOTOF-Q II mass spectrometer equipped with collision-induced dissociation capability. The comparisons of the mass spectra are made in groups of homogenous ligands and mixed TODGA-CMPO ligands clusters. Comparisons are also made based on the complexed metals (Am and lanthanides). Preliminary data (300 words): Collision-induced dissociation mass spectrometry data are collected on two ligands complexed with metal nitrates where the two ligands are homogenous, with (CMPO)2 or (TODGA)2, or heterogeneous, with (TODGA)(CMPO). Several fragmentation patterns are observed among complexes with the CMPO ligand whereas the TODGA ligand commonly dissociates intact from the complex. Most of the metal complexes exhibit similar fragmentation patterns, but there are a few notable deviations in fragmentation patterns between the Am and Ln-bearing complexes. For the [M(CMPO)2(NO3)2]+ complexes, the initial loss of nitrate in the form of nitric acid is observed in all four complexes. However, [Am(CMPO)2(NO3)2]+ exhibits an additional fragmentation not found in the lanthanide complexes. Also, a significantly different ratio of the second nitric acid loss is found in the Am complex. These deviations may indicate the different interaction behaviors between actinides and lanthanides. The [M(TODGA)2(NO3)2]+ complexes exhibit the fragmentation as the loss of one TODGA ligand as an intact form and the loss of nitrate as nitric acid. The Am complex exhibits an additional fragmentation after losing the TOGDA ligand, which is not observed among the Ln complexes. The heterogeneous [M(TODGA)(CMPO)(NO3)2]+ complexes exhibit both similarities and differences between the Am and Ln complexes. For example, the heterogenous Am complex does not exhibit the loss of an intact TODGA ligand while all three Ln complexes do. This indicates that TODGA may bind more strongly to Am than Ln. Additionally, the intensity of the loss of CMPO ligand (as partially or whole) is found to be significantly larger than that of the loss of TODGA (as partially of whole) indicating that TODGA is bound to the metal significantly stronger than CMPO. Planned computational analysis will help understand the deviation in fragmentation behaviors between americium and lanthanide metal centers, or between TODGA and CMPO ligands. Novel aspect (20 words): Gas-phase actinide and lanthanide complex formation and fragmentation provide insight into the coordination environment differences of f-element metals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Milestone 1.2.15: Feasibility of In Situ Accelerated Aluminum Coupon Radiolysis by Synchrotron X-Rays

Extended dry storage of aluminum-clad spent nuclear fuel (ASNF) requires an assessment of the radiolytic generation of molecular hydrogen gas (H2) from the ASNF’s corrosion layers. H2 accumulation can potentially lead to storage canister embrittlement/rupture and the accumulation of flammable gas mixtures in accident scenarios. To date, computational models have been developed for the prediction of radiolytic H2 generation from samples exposed to lower absorbed dose regimes (up to ~3 MGy). However, greater accuracy is needed for higher absorbed doses (> 25 MGy) where the concentration of H2 ultimately reaches a steady-state. Data in this area is limited due to the amount of time taken (months) to accumulate such high gamma doses. Furthermore, a recent study observed radiation-induced damage to the surface of pre-corroded aluminum alloy coupons at high absorbed gamma doses. Despite this observation and its implications, there is currently no computational connection between the radiolytic formation of H2 and changes in the composition and morphology of the cladding’s corrosion layers with absorbed dose. To develop a better understanding of the processes and effects described above, the present study aimed to evaluate the feasibility of leveraging synchrotron x-ray capabilities for coupled accelerated irradiation and in situ surface characterization of ASNF alloys. To that end, National Synchrotron Light Source II (NSLS-II) beamtime was secured and a series of aluminum alloy 1100 (AA1100) wires, prepared under a variety of conditions, were interrogated using ex situ x-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques at Idaho National Laboratory (INL) and ex situ and in situ XRD capabilities at the NSLS-II x-ray powder diffraction (XPD) beamline. Results indicated that performing synchrotron XRD using the available XPD beamline configuration can provide sufficient radiation dose but cannot discern changes in the composition and morphology of sample corrosion layers. Additionally, ex situ XRD and SEM data from Idaho National Laboratory (INL) indicated that the pre-corrosion of AA1100 wires did not generate an appreciably thick corrosion layer, as compared with previous aluminum coupon studies. These thinner surface corrosion layers were not sufficient for detection by both ex situ and in situ synchrotron XRD, specifically under consideration of the NSLS-II XPD beamline’s configuration primarily capturing information from the sample’s bulk material, i.e., aluminum metal. In summary, the use of the NSLS-II XPD beamline for promoting accelerated radiolysis and in situ surface characterization is not appropriate for this program’s goals.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Milestone 1.2.14: Surface Characterization of Irradiated Surrogate Non-Native Corrosion Plumes on Aluminum 6061-T6 Specimens

The United States Department of Energy is seeking to evaluate the feasibility of extended dry storage of aluminum-clad spent nuclear fuel (ASNF) in helium-backfilled cannisters. A significant research effort has been devoted to determining the amount of radiation-induced molecular hydrogen generation from corrosion layers that would be present on the fuel assembly surfaces. However, to date, no evidence of radiation-induced changes in the microstructure of the corroded aluminum surfaces have been reported. This report provides surface characterization, in terms of corrosion layer composition and morphology, for aluminum alloy 6061-T6 “plume” samples subjected to one of three potential ASNF drying techniques—“vacuum only”, “vacuum + 4 hours at 100 oC”, and “vacuum + 4 hours at 220 oC”—and gamma irradiated (= 53 MGy) in the presence of helium gas with ~0% added relative humidity. At these high absorbed gamma doses, for the first time ever, radiation-induced circular defects were found on the sample surface, regardless of the drying regime employed. Additionally, large cracks that penetrated through the corrosion layer to expose bare aluminum metal were observed in irradiated “plume” specimens subjected to drying conditions of “vacuum + 4 hours at 220 oC”. The nature and implications of these defects on the extended dry storage of ASNF is unclear, requiring further study.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Demonstration of In Situ Down Blending During ZIRCEX Process

The Material Recovery Pilot Plant has successfully demonstrated in situ down-blending of HEU fuel to support INL’s commitment to HALEU production technologies. Depleted uranium pellets, along with an HEU fuel piece were placed in the hydrochlorinator and subsequently declad and oxidized. UOx product was recovered, analyzed, and demonstrated to have reduced enrichment within the targeted range of 20 – 30 % U-235. This first attempt at in situ down-blending will be followed by continued process refinement over the remaining fuel operations at MRPP.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Gamma Radiation-Induced Degradation of Acetohydroxamic Acid (AHA) in Aqueous Nitrate and Nitric Acid Solutions Evaluated by Multiscale Modelling

Acetohydroxamic acid (AHA) has been proposed for inclusion in advanced, single-cycle, used nuclear fuel reprocessing solvent systems for the reduction and complexation of plutonium and neptunium ions. For this application, a detailed description of the degradation of AHA in dilute aqueous nitric acid is required. To this end, we present a comprehensive, multiscale computer model for the coupled radiolytic and hydrolytic degradation of AHA in aqueous sodium nitrate and nitric acid solutions. Rate coefficients for the reactions of AHA and HA with the oxidizing nitrate radical were measured for the first time using pulsed electron radiolysis and used as inputs in the kinetic model. The computer model results are validated by comparison to experimental data from steady state gamma irradiations, for which the agreement is excellent. Here, the presented model accurately predicts the yields of the major degradation products of AHA: acetic acid, hydroxylamine, nitrous oxide, and molecular hydrogen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improving bamboo’s fuel and storage properties with a net energy export through torrefaction paired with catalytic oxidation

Using torrefied char, or biocoal, as solid fuel provides an opportunity to introduce a sustainable feedstock into the energy market. The goals of this study were to investigate how torrefaction improves the energy content and the grindability of a Malaysian bamboo along with understanding the potential for integrated energy recovery from torrefaction gases. The feedstock was torrefied at 250–290 °C for 1 h and the combustion characteristics and grindability of the solid products along with the composition of torrefied gas species were measured. The results showed a beneficial increase in elemental carbon increased from 47 to 63 wt% at 290 °C torrefaction, reflecting an increase in higher heating value from 17.8 to 25.6 MJ/kg. The combustion behavior of all the products appeared to show three distinct combustion zones; however, torrefaction severity leading to higher combustion temperature and time as the fixed carbon augmented with the increase of torrefaction temperature. This increase in severity also lead to more friable and grindable material, and the 290 °C condition required a factor of 2.7 less hold-up time in the mill compared to the raw bamboo, and a factor of 8.5 less energy (938 and 111 kWh/tonne respectively). Through analysis of the gas and volatile formation, a case study showed that catalytic oxidation can convert nearly 100% of the embodied chemical energy into usable thermal energy. These experimental findings were scaled to a 100,000 tonne/y capacity torrefaction plant and in the moderate case of 270 °C operating temperature, the plant has 1.25 GJ/tonne excess energy beyond what the process needs.

09 BIOMASS FUELS↗

Radiolytic Gas Production from Aluminum Coupons (Alloy 1100 and 6061) in Helium Environments—Assessing the Extended Storage of Aluminum Clad Spent Nuclear Fuel

Corrosion of aluminium alloy clad nuclear fuel, during reactor operation and under subsequent wet storage conditions, promotes the formation of aluminium hydroxide and oxyhydroxide layers. These hydrated mineral phases and the chemisorbed and physisorbed waters on their surfaces are susceptible to radiation-induced processes that yield molecular hydrogen gas (H 2 ), which has the potential to complicate the long-term storage and disposal of aluminium clad nuclear fuel through flammable and explosive gas mixture formation, alloy embrittlement, and pressurization. Here, we present a systematic study of the radiolytic formation of H 2 from aluminium alloy 1100 (AA1100) and 6061 (AA6061) coupons in “dry” (~0% relative humidity) and “wet” (50% relative humidity) helium environments. Cobalt-60 gamma irradiation of both aluminium alloy types promoted the formation of H 2 , which increased linearly up to ~2 MGy, and afforded G-values of 1.1 ± 0.1 and 2.9 ± 0.1 for “dry” and “wet” AA1100, and 2.7 ± 0.1 and 1.7 ± 0.1 for “dry” and “wet” AA6061. The negative correlation of H 2 production with relative humidity for AA6061 is in stark contrast to AA1100 and is attributed to differences in the extent of corrosion and varying amounts of adsorbed water in the two alloys, as characterized using optical profilometry, scanning electron microscopy, Raman spectroscopy, and X-ray diffraction techniques.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complete Initial Evaluation of Novel Complexants for Tc Holdback for Simplified Single Cycle Separations.

Management of technetium at the back end of nuclear fuel cycle is complicated by its unique physico-chemical character, but must be addressed to due to the environmental, storage and reprocessing challenges of this fission product. In a single-cycle scenario, the recovery and purification of uranium is particularly challenging due to the tendency of a pertechnetate anion to follow uranyl cation. This report summarizes initial studies directed towards finding the solution for technetium management. Two options for controlling technetium’s chemistry in solvent extraction scenarios were studied. Molecular recognition of pertechnetate by aqueous complexants based on guanidinium moieties was compared to redox manipulation of technetium using dihydrazide reagents. Solvent extraction, potentiometric and nuclear magnetic resonance spectroscopy studies were performed. The influence of guanidinium reagents on the liquid-liquid partitioning of technetium is less pronounced, relative to dihydrazides. Strong impact exerted by dihydrazides originates from the technetium-catalyzed decomposition of such compounds which reduces technetium to a tetravalent, non-extractable state. Although this route of technetium management is very effective the destruction of dihydrazides is undesirable. Guanidinium complexants show a more tempered influence on technetium. The effect on the liquid-liquid partitioning of pertechnetate is evident and likely guided by anion recognition due to ion-pair and hydrogen bond formation. Guanidiniums are stable in presence of technetium as evidenced by nuclear magnetic resonance studies. The steady state chemistry of guanidiniums identify this class of aqueous complexants as solid candidates for structure-function pertechnetate recognition studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Milestone 1.2.11: H 2 Production from Surrogate Non-Native Corrosion Plumes on Aluminum 6061-T6 Fuel Cladding Surrogates

Thick, localized, “non-native” corrosion plumes have been identified on Advanced Test Reactor fuel elements, raising concern on their impact on the radiolytic formation of molecular hydrogen gas (H 2 ) from aluminum-clad spent nuclear fuel (ASNF) under proposed extended (> 50 years) dry storage conditions. Here, we report our findings on H 2 generation from the gamma irradiation (up to 52 MGy) of surrogate “non-native” corrosion plume coupons: ambient-temperature-corroded (~350 days in water) aluminum alloy 6061 (AA6061) coupons in helium gas environments with ~0% added relative humidity. Additionally, we provide a comparison of proposed ASNF drying techniques— vacuum drying only, vacuum drying + 100 °C for 4 hr, and vacuum drying + 220 °C for 4 hr—on the yield of H 2 from these surrogate systems. The presented data indicates that similar amounts of H 2 (~2 × 10–3 µmol J–1) are formed from gamma irradiated AA6061 coupons corroded under different temperature regimes, i.e., ambient/350 days vs. 90 C/30 days. These findings validate current, complimentary modelling predictions based on high-temperature-corrosion irradiation data only. Further, the application of a heat treatment procedure (100 and 220 °C), in conjunction with vacuum drying, accelerated the rate at which a steady-state H 2 yield was attained, in comparison to vacuum only, due to the removal of H 2 precursors in the form of adsorbed waters. Interestingly, within the confidence limits of our measurements, negligible difference in total H 2 yield was found between the two investigated heat treatment procedures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Radiolytic Studies of Single-Cycle Extraction Systems

Presentation reporting the INL Center for Radiation Chemistry Research's activities supporting the development of advanced used nuclear reprocessing technologies through evaluating the radiation robustness of ligands.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Milestone 1.2.10: Steady-state H 2 “roll over” point data for aluminum alloys 1100 and 6061

Extended (> 50 years) dry storage is being evaluated by the U.S. Department of Energy (DOE) for the disposition of ~ 18 metric tons of aluminum-clad spent nuclear fuel (ASNF). Transition of the current ASNF inventory into dry storage—using the standard DOE canister—necessitates a rigorous, predictive understanding of the long-term physical and chemical factors that may influence the integrity of the proposed storage canister, including radiolytic molecular hydrogen (H 2 ) generation. Current model predictions employ initial radiolytic yields of H 2 , the values of which change as the cladding’s H 2 -precursor inventory is depleted and H 2 itself becomes progressively more involved in radiolytic and surface dissociation processes. Consequently, the absorbed radiation dose that this steady-state H 2 yield corresponds to is essential for the evaluation and improvement of model predictions. Here, we report our findings on the long-term generation of H 2 from the gamma irradiation (≤ 36 MGy) of corroded AA1100 and AA6061 coupons in helium environments at ambient temperature and ~ 50% RH. Our findings show that AA1100 systems reached steady-state by ~ 36 MGy, while higher doses were necessary for AA6061 systems. This discrepancy was attributed to the AA6061 coupons developing a thicker corrosion layer that led to the trapping of H 2 and its precursors, and potentially additional chemistries, ultimately delaying the depletion of H 2 precursors and the system’s “roll over” point. Further, current model predictions—based on previous AA1100 data—do not show steady-state attainment until above 120 MGy, which is not the case for the AA1100 data collected here. Consequently, the new alloy dependent data presented here are important for the continued improvement of predictive computer models for evaluating the feasibility of extended storage of ASNF in helium backfilled canisters.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Milestone 1.2.9: Radiolytic Gas Generation Measurements from Helium Backfilled Samples of AA1100 and AA6061 Coupons

Nearly 18 metric tons of aluminum-clad spent nuclear fuel (ASNF) is safely managed by the U.S. Department of Energy (DOE). These assemblies are currently in interim storage, with the intention of extended storage (>50 years) until final disposal. Strategies for the continued safe storage of this material are under evaluation, of which a key criterion is the extent of molecular hydrogen gas (H2) formation from the radiolysis of hydrated (oxy)hydroxide aluminum corrosion layers arising from in-reactor and wet storage conditions. Radiation-induced H2 formation has the potential to compromise cladding and storage canister integrity, in addition to promoting the formation of unfavorable gaseous environments. Consequently, understanding this radiation-induced phenomenon is essential for the development of predictive modeling capabilities to support technical considerations and the identification of radiation related challenges for the extended storage of ASNF. Here, we report radiolytic H2 yields (G-values, G(H2)) from the gamma irradiation of ‘pristine’ and pre-corroded aluminum coupons in helium (He) environments as a function of alloy composition (AA1100 and AA6061), relative humidity, and absorbed gamma dose. Measured yields were lower than corresponding values reported for argon environments, a positive result for proposed extended dry storage strategies that would employ helium as a backfill gas. Interestingly, the presented G(H2)He values are comparable to those previously measured in nitrogen environments, suggesting a He mediated H2 inhibition process, attributed here to Penning ionization.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗