Search NASA⌕ Search

Engineering topics

Pint, Bruce

Publications and source records attributed to Pint, Bruce.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxidation Behavior of Heat-Resistant Type $\mathrm{HK}$ Steel ($\mathrm{HK30Nb}$) at 800 °C

We report the cyclic oxidation behavior of HK30Nb heat-resistant steel processed by laser powder bed fusion (LPBF) was compared to its cast counterpart during exposures in air and air + 10% H 2 O at 800 °C. The specific finer microstructure and lower Mn of the LPBF alloy resulted in lower oxidation rates in dry air and faster establishment of a continuous Cr 2 O 3 scale in air + 10% H 2 O compared to coarse-grained cast HK30Nb with higher Mn. Differences in alloy mechanical strength and therefore their ability to accommodate high temperature and oxidation-induced stresses as well as differences in thermal expansion coefficients between the alloy and the formed oxides (Cr 2 O 3 only for the LPBF and Cr 2 O 3 and MnCr 2 O 4 for the cast specimens) during temperature cycling were found to result in a greater extent of spallation for the LPBF than for the cast alloy in dry air at 800 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Compatibility of Wrought Superalloys with Supercritical CO2

Supercritical CO2 (sCO2) power cycles, particularly direct-fired cycles, have the possibility of revolutionizing clean fossil energy with peak temperatures above 700 °C and wrought precipitation strengthened alloys like Haynes 282™ for structural components. At temperatures <650 °C, it would be desirable to use less expensive alloys, however, steels are known to be susceptible to carburization. Laboratory 300 bar sCO2 autoclave results were collected on a range of alloys including less expensive Ni-based alloys like 825 compared to advanced austenitic steels like alloy 709 at 600 °C. Both alloys 825 and 709 formed thin, protective Cr-rich oxides after 1,000 h. Alloy 825 also was exposed for 1,000 h in sCO2 at 800 °C and compared to a range of Ni-based alloys. Comparing alloys 625, 825, and 282, the mass gain increased with increasing alloy Ti content under these conditions. High Al superalloys did not perform significantly better under these conditions at 800 °C.

Pint, Bruce↗
DOE OSTI2023

Evaluation of the interaction between SiC, pre-oxidized FeCrAlMo with aluminized and pre-oxidized Fe-8Cr-2W in flowing PbLi

We report dissimilar materials interactions are a major concern when liquid metals are used as a working fluid. To simulate a dual-coolant PbLi blanket, chemical vapor deposited (CVD) SiC, pre-oxidized FeCrAlMo (APMT) and pre-oxidized aluminized coating on Fe-8Cr-2 W (F82H) specimens were exposed to flowing commercial Pb-17at.%Li with a peak temperature of 650 °C in a pre-oxidized APMT thermal convection loop (TCL) for 1000 h. Similar to prior results in static PbLi, the coated F82H showed small mass changes and limited degradation of room-temperature tensile properties. After exposure, the α-Al 2 O 3 on the surface coated F82H reacted with the PbLi to form LiAlO 2 . However, no significant Al coating loss or interdiffusion was observed. Mass transfer was observed between the APMT, TCL and the SiC specimens. Fe, Cr and Ni were dissolved into the molten flowing PbLi and transported through the TCL to react with the SiC specimens. Compared to a prior experiment with a majority of bare FeCrAl specimens that were exposed in a TCL with a peak temperature of 700 °C for 1000 h, the SiC reaction was reduced to only a few microns of carbides and silicides. Oxygen dissolved in the molten PbLi sustained the formation of an Al 2 O 3 scale on the surface of the coating and induced the formation of a thin surface SiO 2 layer on the surface of the SiC.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Review of HAYNES® 282® alloy for supercritical CO2 structural applications

In this paper, HAYNES® 282® alloy (282® alloy) properties, microstructure, high temperature oxidation resistance, weldability, and American Society of Mechanical Engineers (ASME) code case highlights are reviewed. The long term performance of high temperature, high strength, creep resistant alloys is critical to the success of supercritical carbon dioxide equipment. Several modern power generation technologies require alloys that can operate continuously at or above 700oC. 282® alloy is a precipitation strengthened nickel based super alloy that meets these requirements. The results of 282® alloy research reviewed in this paper include longterm cyclic oxidation behavior in air and sCO2, independent research and validation of 100k hour creep life, and successful welding of the alloy in the age hardened condition. The latter is critical for joining of hardened components (flanges, piping, heat exchanger internal, etc.) and field repair. Several highlights from the code case for this ASMEapproved material are also presented.

Tossey, Brett↗
DOE OSTI2022

Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Oxidation Lifetime Modeling of 625 and 120 Foils After Long-term Exposure in Flowing Air + 10% ${\hbox {H}_2\hbox {O}}$ at 700 and 800 $^\circ$C

A model describing oxidation kinetics considering simultaneous oxidation and volatilization of external oxide scales was integrated with a CALPHAD-based coupled thermodynamic and kinetic approach to predict the oxidation-induced lifetime of foils of alloys 625 and 120. Long-term exposures in flowing air +10% H 2 O at 700 and 800 °C under two flow velocities were used to validate the modeling results. The time to a critical Cr concentration of 10 wt% at the oxide/alloy interface, t 10 , was shown to correlate with the breakdown of the Cr 2 O 3 scale for the studied experimental conditions. Finally, the modeling approach was extended to consider time-dependent oxidation and volatilization rate constants to develop a more appropriate lifetime criterion for microturbine recuperator foils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Performance of alloy 600 in flowing commercial Cl salt at 600°-750°C

For the next generation of concentrating solar power (CSP) plants, K-Mg-Na chloride salts are being explored as a potential higher temperature thermal storage medium. However, there are concerns about compatibility of structural alloys with the salt. To move beyond simple static pot compatibility experiments while a pumped salt loop is being constructed, thermal convection loops were constructed from ~16wt.%Cr Ni-based alloy 600 and operated for 100-1000 h with peak temperatures of 700° and 750°C. These experiments indicated that alloy 600 was compatible up to 700°C with purified (i.e. low O2-) or dried (low H2O) industrial-sourced Mg-K-Na chloride salt with <10 µm/yr loss. Mass transfer was observed from the hot leg to the cold leg in each experiment and more surface deposits were observed with the dried salt. Post-exposure room temperature tensile tests showed minimal degradation of alloy 600 under these conditions.

Pint, Bruce↗
DOE OSTI2022

Compatibility Of Steels At 450°-650°C In Supercritical CO2 With O2 And H2O Additions

Direct-fired supercritical CO2 (sCO2) power cycles are being commercialized to revolutionize fossil energy as a low-emission power source. However, the cycle will increase O2 and H2O in the sCO2 and the implications of these additions have not been fully studied, particularly for lower cost steels that are needed in the lower temperature segments of the plant. Representative 9 and 12%Cr ferritic-martensitic (FM) steels and conventional and advanced austenitic steels were evaluated at 450-650°C to determine the maximum use temperatures in sCO2 with 1%O2 and 0.1%H2O at 300 bar. Compared to research grade (low impurity) sCO2 in indirect-fired cycles, the mass gains and scale thickness were not significantly changed for FM steels: both formed thick duplex Fe-rich scales. For stainless steels, higher mass gains were observed in all cases with increased Fe-rich oxide nodule formation. After 1000h at 650°C, the measured bulk C content was high for all of the steels with the addition of impurities suggesting a lower maximum operating temperature for steels. The post-exposure impact of the environment on room temperature tensile properties also will be discussed.

Pint, Bruce↗
DOE OSTI2022

Effects of applied stress and grain size on creep-rupture lifetime prediction for Haynes 282 alloy

A multiple-heat set of tensile and creep-rupture data generated from a single laboratory was used to establish and evaluate predictive equations for the average creep-limited lifetime of an aged wrought Haynes 282 alloy using two different time- and temperature-compensated parametric models (those of Larson and Miller and Wilshire et al.). The range of temperatures and stresses used to produce the creep-rupture data used in the analyses revealed that two distinct regimes, above and below the proportional limit, were necessary for more accurate predictions of creep lifetimes over the range of conditions studied. Furthermore, a 2x difference in grain size amongst the three heats revealed a breakdown in the relationship between ultimate tensile strength and creep-rupture time, thus impacting the predictive ability of the Wilshire model. Finally, lifetime predictions based on the formulations from the respective models were compared to other available Haynes 282 datasets and found to reasonably replicate the experimental trends established in other studies.

36 MATERIALS SCIENCE↗