Multiobjective Optimization of Silver-Nanowire Deposition for Flexible Transparent Conducting Electrodes
Not Available
36 MATERIALS SCIENCE↗
Engineering topics
Piper, Robert T.
Publications and source records attributed to Piper, Robert T..
Effects of Residual DMSO Adduct on Photonically Cured MAPbI 3 Solar Cells
Defects and impurities in halide perovskite solar cells can negatively impact device performance and long-term stability. In this study, we identify photonically cured methylammonium (MA) lead iodide films contain a residual adduct, MA 2 Pb 3 I 8 (dimethyl sulfoxide) 2 (MA 2 Pb 3 I 8 (DMSO) 2 ), that reduces photocurrent generation in perovskite solar cells (PSCs). This is evidenced by a decrease in the external quantum efficiency (EQE) near 400 nm. Similar EQE reductions were observed in PSCs produced using high-speed processes but have not been thoroughly examined. Through X-ray diffraction patterns and Fourier transform infrared spectroscopy, we establish the photo-inactive MA 2 Pb 3 I 8 (DMSO) 2 as the culprit for the EQE reduction. Combined experimental and simulation results reveal that the MA 2 Pb 3 I 8 (DMSO) 2 phase is located at the hole transport layer/ interface, not on the surface, resulting in lower quantum efficiency and surface photovoltage in the short wavelength region. The residual adduct is kinetically trapped due to the short processing time (20 ms) and crystallization direction but can be removed by an additional photonic pulse. Furthermore, this study highlights the need for careful examination of resulting materials beyond device efficiency when transitioning from laboratory processing to industrial high-speed methods.
14 SOLAR ENERGY↗
Silver nanowire-indium zinc oxide composite flexible transparent conducting electrodes made by spin-coating and photonic curing
Flexible transparent conducting electrodes (TCE) play a critical role in modern technologies. Eliminating the high-temperature annealing of vacuum- or solution-deposited films will increase production throughput and lower the cost of the final products. Photonic curing uses intense pulses of broadband light to induce material transformations instead of heat. In this work, we combine solution deposition and photonic curing, replacing thermal annealing, to fabricate flexible composite TCE films on plastic polyethylene terephthalate (PET) substrates. The composite TCE films are composed of spin-coated silver nanowire-indium zinc oxide layers. Further, the TCE films’ electrical, optical, and morphological properties are investigated and compared to those of commercially available PET/TCE. A sheet resistance of 15 Ω/sq and an average transmittance from 400 – 700 nm of 77% are achieved with the spin-coated and photonic-cured composite flexible TCE films.
14 SOLAR ENERGY↗
Elucidating Diiodomethane-Induced Improvement in Photonically Cured MAPbI 3 Solar Cells
Diiodomethane (CH 2 I 2 ) has been reported to improve the photonically cured perovskite solar cell (PSC) device performance by reducing pinholes. Here we show that even for pinhole-free methylammonium lead iodide (MAPbI 3 ) made by photonic curing, adding CH 2 I 2 promotes significant performance improvement. We elucidate the mechanisms behind the observed improvement. In addition to current-density versus voltage measurements, we perform a wide variety of characterization to compare the crystallinity, grain structure, optical, chemical, and electrical properties of the photonically cured samples with and without CH 2 I 2 in the MAPbI 3 layer to those of thermally annealed devices. Here, the addition of CH 2 I 2 promotes grain growth in the vertical direction, increases the I/Pb ratio in the final film, and removes the I - ionic diffusion and defect signature associated with iodine interstitials. As a result, we achieve a champion efficiency of 15.04% with MAPbI 3 conversion time of 20 ms, comparable to PSCs that have MAPbI 3 layer thermally annealed for 10 min. Understanding the mechanisms behind additive-induced improvements for non-thermal annealing processes is critical to enabling high-speed PSC manufacturing.
14 SOLAR ENERGY↗
How Optical and Electrical Properties of ITO Coated Willow Glass Affect Photonic Curing Outcome for Upscaling Perovskite Solar Cell Manufacturing
Indium tin oxide (ITO) coated Willow® glass is an excellent substrate for roll-to-roll manufacturing of perovskite solar cells (PSCs) but can have large variability in its optical and electrical properties. Photonic curing uses intense light pulses instead of heat to process materials and can facilitate faster processing speeds in roll-to-roll manufacturing to upscale the production of PSCs. Since the entire film stack can absorb light and contributes to the photonic curing outcome, the substrate materials’ properties play an integral role. Furthermore, we present the effect of ITO transmittance on the photonic curing of nickel nitrate sol-gel precursors into nickel oxide and consequently the performance of PSCs fabricated with only photonic curing and no thermal annealing. Unexpectedly, ITO samples processed by photonic curing show improved optical and electrical properties.
14 SOLAR ENERGY↗
Photonic Curing of Nickel Oxide Transport Layer and Perovskite Active Layer for Flexible Perovskite Solar Cells: A Path Towards High-Throughput Manufacturing
High-throughput roll-to-roll (R2R) manufacturing of perovskite solar cells (PSCs) is currently limited by thermal processes that take tens of minutes each, translating to impractically long annealing tools at high web speeds. In addition, PSCs are usually made with metal oxide transport layer materials that require high temperatures for thermal annealing. Here, we demonstrate the fabrication of PSCs using photonic curing, instead of thermal annealing, to convert NiO x directly from sol-gel precursors for hole transport layers and to crystallize methylammonium lead iodide (MAPbI 3 ) active layers on flexible Willow ® Glass substrates. Photonic curing uses short, intense pulses of light to process materials at a high speed, hence it is compatible with R2R manufacturing. We achieved power conversion efficiencies (PCEs) of 11.7% in forward-scan and 10.9% in reverse-scan for PSCs made with photonic cured NiO x and MAPbI 3 films. Furthermore, both NiO x and MAPbI 3 films could be processed with a single photonic curing pulse, with a web speed of 5.7 m/min, and still produce PCEs comparable to thermally annealed control samples. Based on the single-pulse photonic curing condition for each film, we project a web speed of 26 m/min, laying a pathway to high-throughput production of perovskite solar modules.
14 SOLAR ENERGY↗
Effects of Photonic Curing Processing Conditions on MAPbI 3 Film Properties and Solar Cell Performance
Thermal annealing is the most used postdeposition materials processing method in laboratory research, but due to its slow speed and high energy cost, it is not compatible with the upscaling and commercialization of perovskite solar cell (PSC) manufacturing. Here, we adapt photonic curing (PC), which uses millisecond light pulses to deliver energy to the sample, to replace thermal annealing for crystallization of methylammonium lead iodide (MAPbI 3 ) films and rapid fabrication of PSCs. We study how PC conditions affect the outcome of MAPbI 3 conversion from the precursor to the crystalline perovskite phase by evaluating the films’ optical, crystalline, and morphological properties, as well as PSC performance. The results are understood using simulated film temperature profiles. We show that MAPbI 3 is readily converted under a wide range of PC conditions. While previous reports all used short pulses (<3 ms), we find that longer pulses produce more dense films and higher-performing PSCs. We achieve a champion power conversion efficiency in a PC-processed MAPbI 3 PSC of 11.26% under forward scan and 10.34% under reverse scan, with the processing time for the MAPbI 3 layer reduced by 30,000-fold, from 10 min to 20 ms. Using a 6 in. lamp, spatial uniformity tests show a cross-web efficiency variation of 5%. Our results indicate that using longer pulse lengths, >10 ms, is the best PC strategy for perovskite conversion, and PC is a promising annealing method for large-area, high-throughput PSC manufacturing.
14 SOLAR ENERGY↗
Photonic Curing Enabling High-Speed Processing for Perovskite Solar Cells
The thermal annealing step is the bottleneck to high-throughput manufacturing of perovskite solar cells. In this work, we investigate photonic curing to replace thermal annealing for the sol gel NiO hole transport layer. Using solar cell device current density-voltage performance as a metric, we compare the effects of thermal annealing and photonic curing on the conversion of sol gel NiO films deposited on top of indium tin oxide coated Willow® glass substrates. The significant reduction in processing time validates photonic curing as the enabling tool for high-speed manufacturing.
Xu, Weijie↗