Engineering topics

Pittman, J. L.

Publications and source records attributed to Pittman, J. L..

22 records · Page 2

NASA NTRS1978

An aerodynamic analysis of several hypersonic research airplane concepts from M = 0.2 to 6.0

Several conceptual hypersonic research airplanes, designed within the constraints of a B-52 launch aircraft, have been studied experimentally and analytically at Mach numbers from 0.2 to 6.0. Vehicles built to these criteria for Mach 6 cruise were shown to be feasible, if careful attention was paid to the low speed lift, drag, and high angle of attack stability to assure successful landings and transonic pitch angle maneuvers. The integrated scramjet engine drag was high at subsonic speeds and appears to be constant with Reynolds number. The variable geometry airfoil used previously to improve directional stability was shown to be equally adaptable to the improvement of longitudinal stability. The vortex lattice theory gave good subsonic predictions of lift, drag due to lift, and pitching moments. Wind tunnel tests must be relied on for the drag at zero lift, trim, static margins and lateral-directional stability. The Gentry Hypersonic Arbitrary Body Program gave good predictions of the trends of lift, drag, and pitching moments with angle of attack at Mach numbers above 3, but the level of the values were not consistently predicted. No currently available theory or program gave accurate predictions of directional stability or dihedral effects at hypersonic speeds.

Penland, J. A.↗

NASA NTRS1977

Aerodynamic characteristics at Mach numbers from 0.33 to 1.20 of a wing-body design concept for a hypersonic research airplane

An experimental investigation of the static aerodynamic characteristics of a model of one design concept for the proposed National Hypersonic Flight Research Facility was conducted in the Langley 8 foot transonic pressure tunnel. The experiment consisted of configuration buildup from the basic body by adding a wing, center vertical tail, and a three module or six module scramjet engine. The freestream test Mach numbers were 0.33, 0.80, 0.90, 0.95, 0.98, 1.10, and 1.20 at Reynolds numbers per meter ranging from 4.8 x 1 million to 10.4 x 1 million. The test angle of attack range was approximately -4 deg to 22 deg at constant angles of sideslip of 0 deg and 4 deg; the angle of sideslip ranged from about -6 deg to 6 deg at constant angles of attack of 0 deg and 17 deg. The elevons were deflected 0 deg, -10 deg, and -20 deg with rudder deflections of 0 deg and 15.6 deg.

Dillon, J. L.↗

NASA NTRS1977

Vortex lattice prediction of subsonic aerodynamics of hypersonic vehicle concepts

The vortex lattice method introduced by Lamar and Gloss (1975) was applied to the prediction of subsonic aerodynamic characteristics of hypersonic body-wing configurations. The reliability of the method was assessed through comparison of the calculated and observed aerodynamic performances of two National Hypersonic Flight Research Facility craft at Mach 0.2. The investigation indicated that a vortex lattice model involving 120 or more panel elements can give good results for the lift and induced drag coefficients of the craft, as well as for the pitching moment at angles of attack below 10 to 15 deg. Automated processes for calculating the local slopes of mean-camber surfaces may also render the method suitable for use in preliminary design phases.

Pittman, J. L.↗

NASA NTRS1977

Effect of an integrated scramjet installation on the subsonic performance of an aircraft designed to Mach 6 cruise

Various factors contributing to the high drag caused by the installation of a six-module scramjet engine were determined from wind tunnel tests at Mach numbers from 0.2 to 0.7. Methods for alleviating this drag were also explored. The external exhaust nozzle, required for good cruise performance, was a major contributor. Of the drag produced by the engine modules, a significant fraction was attributable to wall divergence in the combustor. Good drag simulation could be achieved by using a single fuel injection strut having approximately the same cross-sectional area as the three used on the full-scale engine. External exhaust nozzle fences had a small but beneficial effect on maximum L/D and a flap which diverted the flow away from the inlet was effective in decreasing drag but only at low angles of attack.

Johnston, P. J.↗