Search NASA⌕ Search

Engineering topics

Pittman, James L.

Publications and source records attributed to Pittman, James L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Overview of the Turbine Based Combined Cycle Discipline

The NASA Fundamental Aeronautics Hypersonics project is focused on technologies for combined cycle, airbreathing propulsions systems to enable reusable launch systems for access to space. Turbine Based Combined Cycle (TBCC) propulsion systems offer specific impulse (Isp) improvements over rocket-based propulsion systems in the subsonic takeoff and return mission segments and offer improved safety. The potential to realize more aircraft-like operations with expanded launch site capability and reduced system maintenance are additional benefits. The most critical TBCC enabling technologies as identified in the National Aeronautics Institute (NAI) study were: 1) mode transition from the low speed propulsion system to the high speed propulsion system, 2) high Mach turbine engine development, 3) transonic aero-propulsion performance, 4) low-Mach-number dual-mode scramjet operation, 5) innovative 3-D flowpath concepts and 6) innovative turbine based combined cycle integration. To address several of these key TBCC challenges, NASA s Hypersonics project (TBCC Discipline) initiated an experimental mode transition task that includes an analytic research endeavor to assess the state-of-the-art of propulsion system performance and design codes. This initiative includes inlet fluid and turbine performance codes and engineering-level algorithms. This effort has been focused on the Combined Cycle Engine Large-Scale Inlet Mode Transition Experiment (CCE LIMX) which is a fully integrated TBCC propulsion system with flow path sizing consistent with previous NASA and DoD proposed Hypersonic experimental flight test plans. This experiment is being tested in the NASA-GRC 10 x 10 Supersonic Wind Tunnel (SWT) Facility. The goal of this activity is to address key hypersonic combined-cycle-engine issues: (1) dual integrated inlet operability and performance issues unstart constraints, distortion constraints, bleed requirements, controls, and operability margins, (2) mode-transition constraints imposed by the turbine and the ramjet/scramjet flow paths (imposed variable geometry requirements), (3) turbine engine transients (and associated time scales) during transition, (4) high-altitude turbine engine re-light, and (5) the operating constraints of a Mach 3-7 combustor (specific to the TBCC). The model will be tested in several test phases to develop a unique TBCC database to assess and validate design and analysis tools and address operability, integration, and interaction issues for this class of advanced propulsion systems. The test article and all support equipment is complete and available at the facility. The test article installation and facility build-up in preparation for the inlet performance and operability characterization is near completion and testing is planned to commence in FY11.

Thomas, Scott R.↗
NASA NTRS1993

Shock-dependent, thrust wings for supersonic flow

A new wing concept which lowers the inviscid drag of a wing in supersonic flow is described. The thrust-wing concept uses a secondary shock that occurs to the rear of the maximum thickness location to produce a significant aerodynamic thrust force from the rearward portion of the wing, thus reducing the inviscid drag. The evaluation of the thrust-wing concept is conducted on a delta-wing planform of differing sweep angles and thicknesses at Mach 1.60 over a wide range of lifting conditions.

Pittman, James L.↗
NASA NTRS1992

Supersonic full-potential methods for missile body analysis

Accounts are presented of representative applications to missile bodies of arbitrary shape of methods based on the steady form of the full potential equation. The NCOREL and SIMP full-potential codes are compared, and their results are evaluated for the cases of an arrow wing and a wing-body configuration. Attention is given to the effect of cross-sectional and longitudinal geometries. Comparisons of surface pressure and longitudinal force and moment data for circular and elliptic bodies have shown that the full-potential methods yielded excellent results in attached-flow conditions. Results are presented for a conical star body, waveriders, the Shuttle Orbiter, and a highly swept wing-body cruising at Mach 4.

Pittman, James L.↗
NASA NTRS1990

A computational study of incipient leading-edge separation on a 65-deg delta wing at M = 1.60

A computational study on a 65-deg delta wing at a freestream Mach number of 1.60 has been conducted by obtaining conical Reynolds-averaged Navier-Stokes solutions on a parametric series of geometries which varied in leading-edge radius and/or circular-arc camber. The computational results showed that increasing leading-edge radius or camber can delay the onset of leading-edge separation on the leeside of a delta wing at a specific angle of attack. Reynolds number was varied from 1 x 10 to the 6th to 5 x 10 to the 6th for a turbulent boundary-layer and was shown to have a minor effect on the effectiveness of leading-edge radius and/or camber in delaying the onset of leading-edge separation. Both laminar and turbulent boundary-layer models were investigated at a Reynolds number of 1 x 10 to the 6th, and the predicted flow pattern was found to change from attached flow for the turbulent boundary-layer model to separated flow for the laminar boundary-layer model. Based upon these results, three wind-tunnel models have been designed to be tested in the Langley Unitary Plan Wind Tunnel.

Mcmillin, S. Naomi↗
NASA NTRS1989

A Mach 6 external nozzle experiment with Argon-Freon exhaust simulation

A scramjet exhaust simulation technique for hypersonic wind tunnel testing has been developed. Mixtures of Argon and Freon correctly match the inviscid simulation parameters of Mach number, static-pressure ratio, and the ratio of specific heats at the combustor exit location; this simulation is accomplished at significantly reduced temperatures and without combustion. An investigation of nozzle parametrics in a Mach 6 freestream showed that the external nozzle ramp angle, the cowl trailing-edge angle, an external nozzle flow fence and the nozzle static-pressure ratio significantly affected the external nozzle thrust and pitching moment as measured by the integration of surface-pressure data. A comparison of Argon-Freon and air exhaust simulation showed that the external nozzle thrust and pitching moment were in error by roughly a factor of 2 using air due to the incorrect match of the ratio of specific heats. An assessment of two-dimensional Euler and Navier-Stokes codes for predicting external nozzle aerodynamic characteristics was made by comparing computed and experimental results.

Pittman, James L.↗
NASA NTRS1989

An Euler analysis of a High-Speed Civil Transport (HSCT) concept at Mach 3

A marching Euler solver, GEM3D, was used to predict the Mach 3 flow field for the wing and body of a High-Speed Civil Transport concept. The analysis focused on a typical cruise lift coefficient of 0.1 at alpha = 3 deg. The Euler solution indicated that embedded shocks formed on the upper surface of the inboard wing panel and at the leading-edge of the outboard wing panel, due to its supersonic leading edge condition. According to a simple static-pressure criterion, the embedded wing upper-surface shocks were sufficiently strong to separate a turbulent boundary layer. Comparison of aerodynamic coefficients from the Euler solver with those from linear theory shows that the linear theory estimates of lift and drag are optimistic, which would lead to optimistic estimates of cruise range.

Pittman, James L.↗
NASA NTRS1989

Adaptive computations of multispecies mixing between scramjet nozzle flows and hypersonic freestream

The objective of this paper is to compute the expansion of a supersonic flow through an internal-external nozzle and its viscous mixing with the hypersonic flow of air. The supersonic jet may be that of a multispecies gas other than air. Calculations are performed for one case where both flows are those of air, and another case where a mixture of freon-12 and argon is discharged supersonically to mix with the hypersonic airflow. Comparisons are made between these two cases with respect to gas compositions, and fixed versus flow-adaptive grids. All the computational results are compared successfully with the wind-tunnel tests results.

Baysa, Oktay↗
NASA NTRS1989

An Euler analysis of leading-edge vortex flows on a forebody-strake at supersonic speeds

The flowfield, surface pressure, and integrated forces and moments for a fighter-type forebody with sharp leading-edge strakes have been obtained by numerical solution of the Euler equations. The method is found to correctly predict the leading-edge vortices and embedded shocks which arise at higher angles of attack. Results are presented for the effects of crossflow grid density, artificial viscosity, angle of attack, streamwise station, and camber on the flow characteristics.

Rose, O. J.↗
NASA NTRS1988

A full-potential theory analysis of the supersonic aerodynamics of a 60-deg delta wing-body configuration

Experimental spanwise pressure distributions for a 60-deg delta wing/body of approximate fineness ratio 7.6 have been obtained and compared to predictions using full-potential theory. Analysis was performed at Mach 1.6 for angles of attack in the range 0.8 to 10 deg, and for Mach numbers ranging from 1.4 to 1.8 at lift coefficients 0.3 and 0.4. The intent of the study was to examine an attached flow approach for maneuver wing design in the presence of a fuselage. For the Mach number, angle-of-attack conditions considered, the full-potential theory accurately modeled the pressure distributions provided the flow remained attached. By combining the full-potential theory results with an empirical shock-induced separation criterion, it was found that the onset of shock-induced separation can be predicted. The investigation showed that, if an attached-flow approach is used with an empirical method of indicating shock-induced separation, the full-potential method is capable of being used as an effective tool for designing maneuver wings.

Rose, O. C.↗
NASA NTRS1988

Computational validation of a parabolized Navier-Stokes solver on a sharp-nose cone at hypersonic speeds

Perfect gas computational results from a newly-developed upwind, parabolized Navier-Stokes (PNS) solver are compared with an existing set of experimental laminar results for a 10-deg half-angle circular cone at freestream Mach number of 7.95. Comparisons were performed with surface pressure and heat transfer data, as well as with flowfield pitot measurements. The PNS code predicted the surface quantities accurately up through 20-deg angle-of-attack, including crossflow separation, and correctly defined the location of the bow shock and the edge of the boundary layer. The importance of cell Reynolds number, grid density, and thermal boundary conditions to the accurate prediction of the flowfield are examined through numerical emamples.

Huebner, Lawrence D.↗
NASA NTRS1987

Experimental flowfield visualization of a high alpha wing at Mach 1.62

Experimental oil-flow and tuft patterns and vapor-screen flow-visualization data were obtained on a cambered wing model at Mach = 1.62 for an angle-of attack range of 0-14 deg. These data were used as flow diagnostic tools along with surface-pressure and force data and full-potential theory calculations. A large separation bubble was found on the lower wing surface at low angle of attack. The high-angle-of-attack flowfield was characterized by a large attached-flow leading-edge expansion followed by a crossflow shock. At alpha = 14 deg the crossflow shock apparently induced discrete regions of streamwise separated flow, which were clearly indicated in the vapor-screen and oil-flow photographs.

Pittman, James L.↗