Search NASA⌕ Search

Engineering topics

Pitts, J. I.

Publications and source records attributed to Pitts, J. I..

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Surface grid generation for wing-fuselage bodies

In the application of finite-difference methods to obtain numerical solutions of viscous compressible fluid flow about wing-fuselage bodies, it is advantageous to transform the governing equations to an idealized boundary-fitted coordinate system. The advantages are reduced computational complexity and added accuracy in the application of boundary conditions. The solution process requires that a grid be superimposed on the physical solution domain which corresponds to a uniform grid on a rectangular computational domain (uniform rectangular parallel-epiped). Grid generation is the determination of a one to one relationship between grid points in the physical domain and grid points in the computational domain. A technique for computing wing-fuselage surface grids using the Harris geometry and software for smooth-surface representation is described. Grid spacing control concepts which govern the relationship between the wing-fuselage surface and the computational grid are also presented.

Smith, R. E.↗
NASA NTRS1979

The solution of the three-dimensional viscous-compressible Navier-Stokes equations on a vector computer

The development of a vectorized computer code for the solution of the three-dimensional viscous-compressible Navier-Stokes equations is described. The code is applied on the CDC STAR-100 vector computer which is capable of achieving high result rates when a high degree of parallelism is present in the computations. The computational technique is an explicit time-split MacCormack predictor-corrector algorithm. Since a large volume of data is processed and virtual memory utilized, a data management scheme based on interleaving is used. The program has been applied to obtain the solution of the laminar supersonic flow about a family of three-dimensional corners. The equations of motion are expressed in a generalized form relative to a uniform rectangular computational domain. The metric coefficient and boundary conditions must be supplied for the corresponding physical domain. For calculations with 30,000 grid points, a computational rate of 0.00015 seconds per grid point per time step is observed.

Smith, R. E.↗
NASA NTRS1978

A vectorization of the Jameson-Caughey NYU transonic swept-wing computer program FLO-22-V1 for the STAR-100 computer

The computer program FLO-22 for analyzing inviscid transonic flow past 3-D swept-wing configurations was modified to use vector operations and run on the STAR-100 computer. The vectorized version described herein was called FLO-22-V1. Vector operations were incorporated into Successive Line Over-Relaxation in the transformed horizontal direction. Vector relational operations and control vectors were used to implement upwind differencing at supersonic points. A high speed of computation and extended grid domain were characteristics of FLO-22-V1. The new program was not the optimal vectorization of Successive Line Over-Relaxation applied to transonic flow; however, it proved that vector operations can readily be implemented to increase the computation rate of the algorithm.

Smith, R. E.↗
NASA NTRS1973

Application of phase-change technique to thin sections with heating on both surfaces

A numerical digital computer program was developed to calculate the heat-transfer coefficients for both sides of a one-dimensional finite slab subject to the boundary conditions ascribed to the phase-change coating heat-transfer technique. In a typical tunnel test situation where a thin wing was exposed to heating on both sides, the data reduction procedures for a semi-infinite slab gave heat-transfer coefficients as much as 375 percent too high on the side with the lowest heating. The results from the one-dimensional finite-slab procedure are presented in the form of correction factors to the solution for a semi-infinite slab in terms of parameters normally used with the phase-change heat-transfer technique. These correlations are not restricted to slab thickness or thermophysical properties and are easily used to obtain accurate data on thin model sections.

Hunt, J. L.↗
NASA NTRS1971

Thin wing corrections for phase-change heat-transfer data.

Since no methods are available for determining the magnitude of the errors incurred when the semiinfinite slab assumption is violated, a computer program was developed to calculate the heat-transfer coefficients to both sides of a finite, one-dimensional slab subject to the boundary conditions ascribed to the phase-change coating technique. The results have been correlated in the form of correction factors to the semiinfinite slab solutions in terms of parameters normally used with the technique.

Hunt, J. L.↗