Search NASA⌕ Search

Engineering topics

Plett, E. G.

Publications and source records attributed to Plett, E. G..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Combustion contribution to noise in jet engines

The relative importance of combustion as a source of noise in a flow regime representative of a subsonic jet engine exhaust was investigated. The combustion noise source characteristics were obtained from pressure and temperature fluctuation measurements in the combustor and exhaust nozzle. The similarity between the fluctuations in this source region and the far field noise were compared. In the jet exhaust velocity range between 450 and 660 ft/sec investigated in detail, the frequencies of dominant pressure and temperature fluctuations in the combustor were also the frequencies of the dominant far field noise. The overall noise levels were 14 to 20 dB higher than from a corresponding clean jet in the same velocity range. Thus it seemed clear that the unsteadiness associated with the combustion process was responsible for the dominant noise in the far field. A simple analysis to predict the far field noise due to the internal pressure fluctuations causing exit plane velocity fluctuations produced trends closely resembling the measured results, but under predicted the far field noise over the spectral range examined. The possible reason for the higher far field noise is direct transmission of acoustic waves through the nozzle, which was not accounted for in the prediction scheme.

Plett, E. G.↗
NASA NTRS1975

Combustion intensity and distribution relation to noise generation

Experiments with several different flame holder geometries were conducted to investigate the degree to which combustion roughness can be altered by altering the flame intensity and flame distribution in a ducted combustion system. The effect of admitting primary air through a plane-slotted or a slotted-swirl vane flame holder was compared and the combustion roughness and noise was contrasted with that obtained with a closed front-end perforated can. The slotted front-end burners produced much smoother burning and less noise than the closed front-end can. No advantage was apparent with swirl vs nonswirl when approximately the same inlet flow distribution was maintained. Preheated inlet air provided somewhat smoother combustion as compared with ambient temperature air. The combustion roughness with methyl alcohol was briefly compared with that of isooctane; indications are that it burns more smoothly, but more detailed studies are needed to substantiate these indications.

Plett, E. G.↗
NASA NTRS1974

Fundamental and applied research on core engine/combustion noise of aircraft engines

Some results of a study of the importance of geometrical features of the combustor to combustion roughness and resulting noise are presented. Comparison is made among a perforated can flame holder, a plane slotted flame holder and a plane slotted flame holder which introduces two counter swirling streams. The latter is found to permit the most stable, quiet combustion. Crosscorrelations between the time derivative of chamber pressure fluctuations and far field noise are found to be stronger than between the far field noise and the direct chamber pressure signal. Temperature fluctuations in the combustor nozzle are also found to have a reasonably strong crosscorrelation with far field sound.

Plett, E. G.↗
NASA NTRS1973

Noise generation by ducted combustion systems

Analysis of the interaction between a zone of nonsteady combustion and its confining duct shows that resonant type oscillations occur with resulting noise intensities far greater than from corresponding unconfined flame zones. The blading action on the flow through the compressor and turbine of an engine generates discrete frequency noise which, it is found, is enhanced by the response of the combustion zone in between. Ducted combustor experiments verify the predicted resonant type noise, the amplitude and frequency of which are strongly influenced by the duct dimensions and end impedance. A convergent exit nozzle results in stronger internal resonant noise oscillations but also generates a higher jet velocity, with the attendant jet noise which exceeds noise from inside the duct at jet Mach numbers near unity.-

Chiu, H. H.↗
NASA NTRS1973

Noise characteristics of combustion augmented high speed jets.

Noise generation by a subsonic flow discharging from a combustion chamber is examined with regard to the relative importance of combustion as a source of noise in such a flow system. Measurements of pressure fluctuations inside the combustor are compared with far-field noise measurements by direct cross-correlations. The cross-correlations and derived cross-spectral densities verify that much of the noise originates inside the combustor. A first-order fluid-mechanical perturbation model is used to predict exit plane velocity fluctuations due to internal pressure fluctuations. Far-field noise levels estimated on this basis are in good agreement with measured values. The overall noise level from the combustor/jet is found to be 10 to 20 dB higher than for an equivalent clean, cold jet at the same exit velocity.

Abdelhamid, A. N.↗
NASA NTRS1972

Jet engine exhaust noise due to rough combustion and nonsteady aerodynamic sources

Internal sources are accounted for in terms of fluctuations of mass and momentum at the nozzle exit plane. At low Mach numbers, mass flow fluctuations generated at the exit plane by acoustic resonant type fluctuations inside the engine are found to be dominant. In the subsonic Mach number range between 0.3 and 0.5, exit plane mass flow fluctuations at frequencies characteristic of turbulence become most dominant. Above Mach 0.5, the turbulent momentum fluctuations at the exit plane become dominant, and the jet contribution is not found significant at subsonic speeds.

Plett, E. G.↗