Engineering topics

Plotkin, Kenneth J.

Publications and source records attributed to Plotkin, Kenneth J..

18 records

NASA NTRS2015

Method and System for Weakening Shock Wave Strength at Leading Edge Surfaces of Vehicle in Supersonic Atmospheric Flight

A method and system are provided to weaken shock wave strength at leading edge surfaces of a vehicle in atmospheric flight. One or more flight-related attribute sensed along a vehicle's outer mold line are used to control the injection of a non-heated, non-plasma-producing gas into a local external flowfield of the vehicle from at least one leading-edge surface location along the vehicle's outer mold line. Pressure and/or mass flow rate of the gas so-injected is adjusted in order to cause a Rankine-Hugoniot Jump Condition along the vehicle's outer mold line to be violated.

Daso, Endwell O.↗

NASA NTRS2012

SCAMP: Rapid Focused Sonic Boom Waypoint Flight Planning Methods, Execution, and Results

Successful execution of the flight phase of the Superboom Caustic Analysis and Measurement Project (SCAMP) required accurate placement of focused sonic booms on an array of prepositioned ground sensors. While the array was spread over a 10,000-ft-long area, this is a relatively small region when considering the speed of a supersonic aircraft and sonic boom ray path variability due to shifting atmospheric conditions and aircraft trajectories. Another requirement of the project was to determine the proper position for a microphone-equipped motorized glider to intercept the sonic boom caustic, adding critical timing to the constraints. Variability in several inputs to these calculations caused some shifts of the focus away from the optimal location. Reports of the sonic booms heard by persons positioned amongst the array were used to shift the focus closer to the optimal location for subsequent passes. This paper describes the methods and computations used to place the focused sonic boom on the SCAMP array and gives recommendations for their accurate placement by future quiet supersonic aircraft. For the SCAMP flights, 67% of the foci were placed on the ground array with measured positions within a few thousand feet of computed positions. Among those foci with large caustic elevation angles, 96% of foci were placed on the array, and measured positions were within a few hundred feet of computed positions. The motorized glider captured sonic booms on 59% of the passes when the instrumentation was operating properly.

Haering, Edward A., Jr.↗

NASA NTRS2012

Real-Time, Interactive Sonic Boom Display

The present invention is an improved real-time, interactive sonic boom display for aircraft. By using physical properties obtained via various sensors and databases, the invention determines, in real-time, sonic boom impacts locations and intensities for aircraft traveling at supersonic speeds. The information is provided to a pilot via a display that lists a selectable set of maneuvers available to the pilot to mitigate sonic boom issues. Upon selection of a maneuver, the information as to the result of the maneuver is displayed and the pilot may proceed with making the maneuver, or provide new data to the system in order to calculate a different maneuver.

Haering, Jr., Edward A.↗

NASA NTRS2011

Focused and Steady-State Characteristics of Shaped Sonic Boom Signatures: Prediction and Analysis

The objective of this study is to examine the effect of flight, at off-design conditions, on the propagated sonic boom pressure signatures of a small "low-boom" supersonic aircraft. The amplification, or focusing, of the low magnitude "shaped" signatures produced by maneuvers such as the accelerations from transonic to supersonic speeds, climbs, turns, pull-up and pushovers is the concern. To analyze these effects, new and/or improved theoretical tools have been developed, in addition to the use of existing methodology. Several shaped signatures are considered in the application of these tools to the study of selected maneuvers and off-design conditions. The results of these applications are reported in this paper as well as the details of the new analytical tools. Finally, the magnitude of the focused boom problem for "low boom" supersonic aircraft designs has been more accurately quantified and potential "mitigations" suggested. In general, "shaped boom" signatures, designed for cruise flight, such as asymmetric and symmetric flat-top and initial-shock ramp waveforms retain their basic shape during transition flight. Complex and asymmetric and symmetric initial shock ramp waveforms provide lower magnitude focus boom levels than N-waves or asymmetric and symmetric flat-top signatures.

Maglieri, Domenic J.↗

NASA NTRS2011

N plus 3 Advanced Concept Studies for Supersonic Commercial Transport Aircraft Entering Service in the 2030-2035 Period

Boeing, with Pratt & Whitney, General Electric, Rolls-Royce, M4 Engineering, Wyle Laboratories and Georgia Institute of Technology, conducted a study of supersonic commercial aircraft concepts and enabling technologies for the year 2030-2035 timeframe. The work defined the market and environmental/regulatory conditions that could evolve by the 2030/35 time period, from which vehicle performance goals were derived. Relevant vehicle concepts and technologies are identified that are anticipated to meet these performance and environmental goals. A series of multidisciplinary analyses trade studies considering vehicle sizing, mission performance and environmental conformity determined the appropriate concepts. Combinations of enabling technologies and the required technology performance levels needed to meet the desired goals were identified. Several high priority technologies are described in detail, including roadmaps with risk assessments that outline objectives, key technology challenges, detailed tasks and schedules and demonstrations that need to be performed. A representative configuration is provided for reference purposes, along with associated performance estimates based on these key technologies.

Welge, H. Robert↗

NASA NTRS2006

Analysis of Acoustic Modeling and Sound Propagation in Aircraft Noise Prediction

An analysis has been performed of measured and predicted aircraft noise levels around Denver International Airport. A detailed examination was made of 90 straight-out departures that yielded good measurements on multiple monitors. Predictions were made with INM 5, INM 6 and the simulation model NMSIM. Predictions were consistently lower than measurements, less so for the simulation model than for the integrated models. Lateral directivity ("installation effect") patterns were seen which are consistent with other recent measurements. Atmospheric absorption was determined to be a significant factor in the underprediction. Calculations of atmospheric attenuation were made over a full year of upper air data at seven locations across the United States. It was found that temperature/humidity effects could cause variations of up to +/-4 dB, depending on season, for the sites examined. It was concluded that local temperature and humidity should be accounted for in aircraft noise modeling.

Plotkin, Kenneth J.↗

NASA NTRS2005

Measured Effects of Turbulence on the Loudness and Waveforms of Conventional and Shaped Minimized Sonic Booms

Turbulence has two distinctive effects on sonic booms: there is distortion in the form of random perturbations that appear behind the shock waves, and shock rise times are increased randomly. A first scattering theory by S.C. Crow in the late 1960s quantified the random distortions, and Crow's theory was shown to agree with available flight test data. A variety of theories for the shock thickness have been presented, all supporting the role of turbulence in increasing rise time above that of a basic molecular-relaxation structure. The net effect of these phenomena on the loudness of shaped minimized booms is of significant interest. Initial analysis suggests that there would be no change to average loudness, but this had not been experimentally investigated. The January 2004 flight test of the Shaped Sonic Boom Demonstrator (SSBD), together with a reference unmodified F-5E, included a 12500- foot linear ground sensor array with 28 digitally recorded sensor sites. This data set provides an opportunity to re-test Crow's theory for the post-shock perturbations, and to examine the net effect of turbulence on the loudness of shaped sonic booms.

Plotkin, Kenneth J.↗

NASA NTRS2005

Flight Demonstration Of Low Overpressure N-Wave Sonic Booms And Evanescent Waves

The recent flight demonstration of shaped sonic booms shows the potential for quiet overland supersonic flight, which could revolutionize air transport. To successfully design quiet supersonic aircraft, the upper limit of an acceptable noise level must be determined through quantitative recording and subjective human response measurements. Past efforts have concentrated on the use of sonic boom simulators to assess human response, but simulators often cannot reproduce a realistic sonic boom sound. Until now, molecular relaxation effects on low overpressure rise time had never been compared with flight data. Supersonic flight slower than the cutoff Mach number, which generates evanescent waves, also prevents loud sonic booms from impacting the ground. The loudness of these evanescent waves can be computed, but flight measurement validation is needed. A novel flight demonstration technique that generates low overpressure N-waves using conventional military aircraft is outlined, in addition to initial quantitative flight data. As part of this demonstration, evanescent waves also will be recorded.

Haering, Edward A., Jr.↗

NASA NTRS2000

Examination of the Lateral Attenuation of Aircraft Noise

Measurements of the lateral attenuation of noise from aircraft operations at Denver International Airport were made at distances up to 2000 feet and elevation angles up to 27 degrees. Attenuation Calculated from modem ground impedance theory agrees well with average measured attenuation. The large variability between measured and predicted levels observed at small elevation angles is demonstrated to be due to refraction by wind and temperature gradients.

Plotkin, Kenneth J.↗

NASA NTRS2000

Validation of Aircraft Noise Prediction Models at Low Levels of Exposure

Aircraft noise measurements were made at Denver International Airport for a period of four weeks. Detailed operational information was provided by airline operators which enabled noise levels to be predicted using the FAA's Integrated Noise Model. Several thrust prediction techniques were evaluated. Measured sound exposure levels for departure operations were found to be 4 to 10 dB higher than predicted, depending on the thrust prediction technique employed. Differences between measured and predicted levels are shown to be related to atmospheric conditions present at the aircraft altitude.

Page, Juliet A.↗

NASA NTRS2000

Validation of Aircraft Noise Prediction Models at Low Levels of Exposure

Page, Juliet A.↗

NASA NTRS1996

Theoretical Basis for Finite Difference Extrapolation of Sonic Boom Signatures

Calculation of sonic boom signatures for aircraft has traditionally followed the methods of Whitham' and Walkden. The wave disturbance generated by the vehicle is obtained by area rule linearized supersonic flow methods, which yield a locally axisymmetric asymptotic solution. This solution is acoustic in nature, i.e., first order in disturbance quantities, and corresponds to ray acoustics. Cumulative nonlinear distortion of the signature is incorporated by using this solution to adjust propagation speed to first order, thus yielding a solution second order in disturbance quantities. The effects of atmospheric gradients are treated by Blokhintzov's method of geometrical acoustics. Both nonlinear signature evolution and ray tracing are applied as if the pressure field very close to the vehicle were actually that given by the source term (the 'F-function') of the asymptotic linearized flow solution. The viewpoint is thus that the flow solution exists at a small radius near the vehicle, and may be treated as an input to an extrapolation procedure consisting of ray tracing and nonlinear aging. The F-function is often regarded as a representation of a near-field pressure signature, and it is common for computational implementations to treat it interchangeably with the pressure signature. There is a 'matching radius' between the source function and the subsequent propagation extrapolation. This viewpoint has been supported by wind tunnel tests of simple models, and very typically yields correct results for actual flight vehicles. The assumption that the F-function and near-field signature are interchangeable is generally not correct. The flowfield of a vehicle which is not axisymmetric contains crossflow components which are very significant at small radii and less so at larger distances. From an acoustical viewpoint, the crossflow is equivalent to source diffraction portions of the wave field. Use of the F-function as a near field signature effectively assumes that the diminution of the crossflow/diffraction component may be applied all at once at the matching radius noted above. This approximation, though not rigorously validated, is responsible for the usual correct far-field results. On the other hand, if an actual near-field signature (either from wind tunnel or CFD data) is used at a starting point rather than one based on th effective source distribution, the predicted far-field signature is generally wrong.

Plotkin, Kenneth J.↗

NASA NTRS1996

Validation of Aircraft Noise Models at Lower Levels of Exposure

Noise levels around airports and airbases in the United States arc computed via the FAA's Integrated Noise Model (INM) or the Air Force's NOISEMAP (NMAP) program. These models were originally developed for use in the vicinity of airports, at distances which encompass a day night average sound level in decibels (Ldn) of 65 dB or higher. There is increasing interest in aircraft noise at larger distances from the airport. including en-route noise. To evaluate the applicability of INM and NMAP at larger distances, a measurement program was conducted at a major air carrier airport with monitoring sites located in areas exposed to an Ldn of 55 dB and higher. Automated Radar Terminal System (ARTS) radar tracking data were obtained to provide actual flight parameters and positive identification of aircraft. Flight operations were grouped according to aircraft type. stage length, straight versus curved flight tracks, and arrival versus departure. Sound exposure levels (SEL) were computed at monitoring locations, using the INM, and compared with measured values. While individual overflight SEL data was characterized by a high variance, analysis performed on an energy-averaging basis indicates that INM and similar models can be applied to regions exposed to an Ldn of 55 dB with no loss of reliability.

Page, Juliet A.↗

NASA NTRS1994

USAF single-event sonic boom prediction model: PCBoom3

The Air Force has developed PCBoom3, a general-purpose, single-event sonic boom prediction model. The model operates on an IBM PC or compatible, under DOS or Windows. It is accessed via an integrated environment which controls building of input cases, running boom calculations, displaying contours and signatures, and managing all associated data. The primary boom calculation is via a variation of FOBOOM, the focus-boom extension of Thomas's program. Aircraft input is either via a user-provided F-function, or simple N-wave F-functions tabulated for about 20 current aircraft. A fast boom calculation, based on Plotkin's SBORT algorithms, is included for simple N-wave F-functions in a windless atmosphere and flight altitudes up to 60,000 feet. After a run is complete, the user can access an index identifying significant events (focal zones, beginning of footprint, etc.), then plot boom amplitude contours and signatures or spectra at any point in the footprint. The primary uses of this program are expected to be operational planning and boom incident investigation. However, because of the commonality between FOBOOM and the MDBOOM program currently being used for low boom configuration design, this program is of interest to the HSCT community, especially as supersonic route planning activity increases. The Air Force recently conducted a flight test program to evaluate the focal zone capabilities of PCBoom3. Initial results of that program validate the prediction of focal zone geometry, amplitudes, and waveforms.

Plotkin, Kenneth J.↗

NASA NTRS1994

On the aging of sonic booms

This paper presents view-graphs and notes on sonic boom aging. Topic covered include sonic boom propagation, George's minimized F-function, final minimum shock boom, amplitude and age parameters, off-track aging, scaling flight test experiments, the potential for thin shocks, and results of a Boomfile flight test that showed significant waveform distortion.

Plotkin, Kenneth J.↗

NASA NTRS1992

The effect of turbulence on the loudness of minimized sonic boom signatures

An important issue for shaped minimized sonic booms is whether turbulence-induced distortions will adversely affect the benefits gained by shaping. This question was considerably simplified by two recent results. The first is the finding that the loudness of sonic booms is well quantified by loudness. The second is that loudness of a shaped boom is dominated by the shock waves. The issue is now the effect of turbulence on weak (1 psf or less) sonic booms. Since it is clear that molecular relaxation effects have a significant effect on shock structure and loudness, turbulence effects must be examined in conjunction with relaxation-thickened shocks. This analysis must be directed toward loudness calculations and include all pertinent mechanisms.

Plotkin, Kenneth J.↗

NASA NTRS1992

The effect of turbulence and molecular relaxation on sonic boom signatures

Our objectives are to assess the effect of turbulence and molecular absorption (which is now known to be a key factor in sonic boom shock structure) on shaped sonic booms. Today I will discuss the combination of physical mechanisms for idealized turbulence. In parallel, we are reviewing models for mixed layer turbulence, and these physical effects will eventually be generalized.

Plotkin, Kenneth J.↗

NASA NTRS1991

Sonic Boom

A status of the knowledge of sonic booms is provided, with emphasis on their generation, propagation and prediction. For completeness, however, material related to the potential for sonic boom alleviation and the response to sonic booms is also included. The material is presented in the following sections: (1) nature of sonic booms; (2) review and status of theory; (3) measurements and predictions; (4) sonic boom minimization; and (5) responses to sonic booms.

Maglieri, Domenic J.↗