Engineering topics

Poeschel, R. L.

Publications and source records attributed to Poeschel, R. L..

At least 19 records

NASA NTRS1991

HOLLOTRON switch for megawatt lightweight space inverters

The feasibility of satisfying the switching requirements for a megawatt ultralight inverter system using HOLLOTRON switch technology was determined. The existing experimental switch hardware was modified to investigate a coaxial HOLLOTRON switch configuration and the results were compared with those obtained for a modified linear HOLLOTRON configuration. It was concluded that scaling the HOLLOTRON switch to the current and voltage specifications required for a megawatt converter system is indeed feasible using a modified linear configuration. The experimental HOLLOTRON switch operated at parameters comparable to the scaled coaxial HOLLOTRON. However, the linear HOLLOTRON data verified the capability for meeting all the design objectives simultaneously including current density (greater than 2 A/sq cm), voltage (5 kV), switching frequency (20 kHz), switching time (300 ns), and forward voltage drop (less than or equal to 20 V). Scaling relations were determined and a preliminary design was completed for an engineering model linear HOLLOTRON switch to meet the megawatt converter system specifications.

Poeschel, R. L.↗

NASA NTRS1984

Ion thruster system (8-cm) cyclic endurance test

This report describes the qualification test of an Engineering-Model 5-mN-thrust 8-cm-diameter mercury ion thruster which is representative of the Ion Auxiliary Propulsion System (IAPS) thrusters. Two of these thrusters are scheduled for future flight test. The cyclic endurance test described herein was a ground-based test performed in a vacuum facility with a liquid-nitrogen-cooled cryo-surface and a frozen mercury target. The Power Electronics Unit, Beam Shield, Gimal, and Propellant Tank that were used with the thruster in the endurance test are also similar to those of the IAPS. The IAPS thruster that will undergo the longest beam-on-time during the actual space test will be subjected to 7,055 hours of beam-on-time and 2,557 cycles during the flight test. The endurance test was successfully concluded when the mercury in the IAPS Propellant Tank was consumed. At that time, 8,471 hours of beam-on-time and 599 cycles had been accumulated. Subsequent post-test-evaluation operations were performed (without breaking vacuum) which extended the test values to 652 cycles and 9,489 hours of beam-on-time. The Power Electronic Unit (PEU) and thruster were in the same vacuum chamber throughout the test. The PEU accumulated 10,268 hr of test time with high voltage applied to the operating thruster or dummy load.

Dulgeroff, C. R.↗

NASA NTRS1984

IAPS (8-cm) ion thruster cyclic endurance test

Attention is given to the cyclic endurance qualification test, performed in a vacuum facility with a liquid nitrogen-cooled cryosurface and a frozen mercury target, to which a mercury-ion thruster representative of Ion Auxiliary Propulsion System (IAPS) thrusters was subjected. At the time that the endurance test was successfully concluded, upon consumption of the IAPS propellant tank's mercury, 8,471 hours of 'beam-on time' and 599 cycles had been accumulated. The system's Power Electronics Unit accumulated 10,268 hours of test time with high voltage applied to the operating thruster or dummy load.

Dulgeroff, C. R.↗

NASA NTRS1984

Ion propulsion for communications satellites

In a recent study of potential applications for electric propulsion, it was determined that ion propulsion can provide North-South stationkeeping (NSSK) for communication satellites in geosynchronous orbit with appreciably less mass than chemical propulsion. While this finding is not new, the margin of benefit over advanced chemical propulsion technology depends strongly on the ion propulsion system specifications. Full advantage must be taken of the under-utilized stored energy available from the communication satellite's batteries. This paper describes a methodology for evaluating the benefits obtained in using ion propulsion for NSSK, both in terms of the mass reduction and its economic value.

Poeschel, R. L.↗

NASA NTRS1984

Ring-cusp ion thrusters

The high performance ion thruster technology presented is suitable for either geostationary satellite north-south stationkeeping or interplanetary spacecraft primary propulsion. The thruster employs a ring-cusp magnetic field arrangement for plasma confinement, incurring an ion production cost which at about 100 eV/ion, is approximately half the value for the state-of-the-art J-series mercury ion thruster. A comparison of the average plasma properties existing within the ion-production volumes indicates that the improved performance of the ring-cusp configuration is due to higher electron temperature, confirming the superiority of this design in confining the energetic electrons emitted by the cathode.

Beattie, J. R.↗

NASA NTRS1983

Evaluation of the use of on-board spacecraft energy storage for electric propulsion missions

On-board spacecraft energy storage represents an under utilized resource for some types of missions that also benefit from using relatively high specific impulse capability of electric propulsion. This resource can provide an appreciable fraction of the power required for operating the electric propulsion subsystem in some missions. The most probable mission requirement for utilization of this energy is that of geostationary satellites which have secondary batteries for operating at high power levels during eclipse. The study summarized in this report selected four examples of missions that could benefit from use of electric propulsion and on-board energy storage. Engineering analyses were performed to evaluate the mass saved and economic benefit expected when electric propulsion and on-board batteries perform some propulsion maneuvers that would conventionally be provided by chemical propulsion. For a given payload mass in geosynchronous orbit, use of electric propulsion in this manner typically provides a 10% reduction in spacecraft mass.

Poeschel, R. L.↗

NASA NTRS1983

Development of advanced inert-gas ion thrusters

Inert gas ion thruster technology offers the greatest potential for providing high specific impulse, low thrust, electric propulsion on large, Earth orbital spacecraft. The development of a thruster module that can be operated on xenon or argon propellant to produce 0.2 N of thrust at a specific impulse of 3000 sec with xenon propellant and at 6000 sec with argon propellant is described. The 30 cm diameter, laboratory model thruster is considered to be scalable to produce 0.5 N thrust. A high efficiency ring cusp discharge chamber was used to achieve an overall thruster efficiency of 77% with xenon propellant and 66% with argon propellant. Measurements were performed to identify ion production and loss processes and to define critical design criteria (at least on a preliminary basis).

Poeschel, R. L.↗

NASA NTRS1981

Retrofit and acceptance test of 30-cm ion thrusters

Six 30 cm mercury thrusters were modified to the J-series design and evaluated using standardized test procedures. The thruster performance meets the design objectives (lifetime objective requires verification), and documentation (drawings, etc.) for the design is completed and upgraded. The retrofit modifications are described and the test data for the modifications are presented and discussed.

Poeschel, R. L.↗

NASA NTRS1981

Characteristics of 30-centimeter mercury ion thrusters

The technology development of the 30-cm J-series mercury ion thruster for prime propulsion application in solar electric propulsion systems has been conducted at NASA-Lewis Research Center. This development included the fabrication and testing of the 30-cm thruster. The present J-series thruster design is the result of an intensive effort to eliminate real and potential design deficiencies that were uncovered during initial endurance, structural, and performance tests. A standardized set of test and data recording procedure was formulated to allow for the characterization of the J-series thruster. This paper briefly reviews the design of the J-series thruster and presents a compilation of recent test results that define the J-series thruster characteristics.

Maloy, J. E.↗

NASA NTRS1981

Electric propulsion - characteristics, applications, and status

A comparative review of the principles of ion thruster and chemical rocket operations is presented. The 30cm mercury ion thruster development and the specifications imposed on it by the Solar Electric propulsion System program are discussed. The 30cm thruster operating range, efficiency, wear out lifetime, and interface requirements are described.

Maloy, J. E.↗

NASA NTRS1981

Characteristics of 30-centimeter mercury ion thrusters

The technology development of the 30 centimeter J series mercury ion thruster for prime propulsion application in solar electric propulsion systems is described. Thruster design is reviewed. A standardized set of test and data recording procedures formulated to allow for the characterization of the J series thruster is described. Characteristics measured are the magnetic baffle characterization, the neutralizer characterization, perveance, the minimum eV/ion measurement, and the electrical and propellant utilization efficiency measurements. Test results are presented.

Maloy, J. E.↗

NASA NTRS1981

Electric propulsion - Characteristics, applications, and status

As chemical propulsion systems were achieving their ultimate capability for planetary exploration, space scientists were developing solar electric propulsion as the propulsion system need for future missions. This paper provides a comparative review of the principles of ion thruster and chemical rocket operations and discusses the current status of the 30-cm mercury ion thruster development and the specifications imposed on the 30-cm thruster by the Solar Electric Propulsion System program. The 30-cm thruster operating range, efficiency, wear out lifetime, and interface requirements are described. Finally, the areas of 30-cm thruster technology that remain to be refined are discussed.

Maloy, J. E.↗

NASA NTRS1981

30-cm mercury ion thruster technology

The LeRC/Hughes 30-cm mercury ion thruster has been developed to a state of maturity such that is has become meaningful to formulate models for describing the performance characteristics of the major subassemblies. The thruster hollow cathode and the ion optics subassemblies have been investigated with this objective and conceptual, semiquantitative models have been formulated for relating lifetime and performance capabilities to design and operating parameters. This paper summarizes the investigations, discusses the factors considered for inclusion in the models, and describes the status of the models.

Poeschel, R. L.↗

NASA NTRS1981

Characteristics of the LeRC/Hughes J-series 30-cm engineering model thruster

As a consequence of endurance and structural tests performed on 900-series engineering model thrusters (EMT), several modifications in design were found to be necessary for achieving performance goals. The modified thruster is known as the J-series EMT. The most important of the design modifications affect the accelerator grid, gimbal mount, cathode polepiece, and wiring harness. The paper discusses the design modifications incorporated, the condition(s) they corrected, and the characteristics of the modified thruster.

Collett, C. R.↗

NASA NTRS1980

Retrofit and verification test of a 30-cm ion thruster

Twenty modifications were found to be necessary and were approved by design review. These design modifications were incorporated in the thruster documents (drawings and procedures) to define the J series thruster. Sixteen of the design revisions were implemented in a 900 series thruster by retrofit modification. A standardized set of test procedures was formulated, and the retrofit J series thruster design was verified by test. Some difficulty was observed with the modification to the ion optics assembly, but the overall effect of the design modification satisfies the design objectives. The thruster was tested over a wide range of operating parameters to demonstrate its capabilities.

Dulgeroff, C. R.↗

NASA NTRS1980

Analysis and design of ion thruster for large space systems

Design analyses showed that an ion thruster of approximately 50 cm in diameter will be required to produce a thrust of 0.5 N using xenon or argon as propellants, and operating the thruster at a specific impulse of 3530 sec or 6076 sec respectively. A multipole magnetic confinement discharge chamber was specified.

Poeschel, R. L.↗

NASA NTRS1979

Primary Electric Propulsion Technology Study

An investigation of the 30-cm engineering-model-thruster technology with emphasis placed on the development of models for understanding and predicting the operational characteristics and wear-out mechanisms of the thruster as a function of operating or design parameters is presented. The task studies include: (1) the wear mechanisms and wear rates that determine the useful lifetime of the thruster discharge chamber; (2) cathode lifetime as determined by the depletion of barium from the barium-aluminate-impregnated-porous-tungsten insert that serves as a barium reservoir; (3) accelerator-grid-system technology; (4) a verification of the high-voltage propellant-flow-electrical-isolator design developed under NASA contract NAS3-20395 for operation at 10-kV applied voltage and 10-A equivalent propellant flow with mercury and argon propellants. A model was formulated for predicting performance.

Poeschel, R. L.↗

NASA NTRS1978

Extended performance solar electric propulsion thrust system design

A thrust system design has been established for an extended performance technology, 6.4 kW, 4800 sec specific impulse ion thruster. The configuration is comprised of ten thrusters configured with a power management and control subsystem in a modular thrust system design. The system design approach is an adaptation of that previously established for the baseline technology 2.7 kW, 3000 sec specific impulse ion thruster. The power management and control subsystem design includes a combination of individual electronics for each thruster and a set of electronics with redundancy that are common to all thrusters. The thermal dissipation from all electronics is removed with a common heat pipe/radiator assembly.

Cake, J. E.↗