Search NASA⌕ Search

Engineering topics

Polizos, Georgios

Publications and source records attributed to Polizos, Georgios.

At least 19 records

Exploring the potential and impact of single-crystal active materials on dry-processed electrodes for high-performance lithium-ion batteries

Roll-to-roll powder-to-film dry processing (DP) and single-crystal (SC) active materials (AMs) with many advantages are two hot topics of lithium-ion batteries (LIBs). However, DP of SC AMs for LIBs is rarely reported. Consequently, the impact of SC AMs on dry-processed LIBs is not well understood. Herein, for the first time, via a set of experimental and theoretical studies of the conventional polycrystalline-AM- and SC-AM-based DPed electrodes (DPEs), this work not only reports a high-performance dry SC-AM cathode for LIB manufacturing, but also establishes some fundamental understanding of SC-based dry-processed electrodes, including their morphology, structure, mechanical strength, electronic conductivity and LIB electrochemical behavior. Further, the results suggest that DP of SC AMs is promising, which can dramatically improve the electrochemical kinetics at electrode level and particle level. Specifically, for the rate capability and long-term cyclability in full cells, SC DPEs exhibit a discharge specific capacity of 152.1 mAh g -1 at 1C and a capacity retention rate of 79.9 % at C/3 over 500 cycles, which are superior to those of PC DPEs (135.6 mAh g -1 and 68.3 %) at the same conditions and are further confirmed by the simulation data from the theoretical modelling study. Therefore, this comprehensive work marks a significant milestone for DP strategy and SC AMs, enlightening future research and development of LIB manufacturing.

25 ENERGY STORAGE↗

Comprehensive evaluation of commercially scalable atomic-layer-deposited alumina coating impact on full cell battery performance across varied test conditions

Atomic Layer Deposition (ALD) has emerged as a strategic enhancement method for lithium-ion battery (LIB) materials offering potential benefits and durability benefits for industrial battery production. However, the translation from laboratory achievements to commercial-scale applications has been limited. Here, this study aims to bridge this gap by comprehensively evaluating the effects of commercially scalable Al 2 O 3 ALD coatings using full pouch cell performance as a means to assess the ALD impact. We utilized large-scale slot-die coating techniques to ensure consistent electrode quality and tested four configurations of pouch cells to analyze the individual effects of ALD coating on anode and cathode electroactive materials. Our extensive testing matrix included long-term cycling, fast discharge, fast charge, leakage current, and high voltage tests. While at lower C-rates (<~1C), the influence of Al 2 O 3 coatings on cell performance is not significant. Fast charging conditions reveal that the anode ALD coating significantly enhances performance via a passivating effect, while on the cathode, it is detrimental, potentially due to increased resistance of the thin interfacial layer formed during the ALD processing. Leakage current and high-voltage tests show that the application of ALD coatings on either anode or cathode effectively minimizes side reactions at the electrode-electrolyte interface. Additionally, ALD coatings significantly mitigate concentrated and localized lithium plating on the anodes. These insights provide a valuable understanding of the potential of ALD technologies in LIB manufacturing to tailor cell performance, paving the way for safer, more efficient, and cost-effective battery solutions.

25 ENERGY STORAGE↗

Mechanical and Electrochemical Implications of Drying Temperature on Lithium‐Ion Battery Electrodes

Abstract Lithium‐ion battery (LIB) electrodes are typically produced with n‐methyl‐2‐pyrrolidone, a toxic solvent that is a known carcinogen and reproductive hazard. Accordingly, aqueous processing has been an expanding area of research interest in the field of LIB manufacturing. Although aqueous processing has been widely successful in anode processing, serious challenges remain in processing the cathode. In this work, the drying mechanics of cathode processed with both solvents is investigated though implementation of a chemical‐engineering‐based model to better understand the utilization of heat provided by experimentally determining the heat and mass transfer coefficients. Electrochemical performance is also evaluated to determine the impact of drying temperature on cycling performance. Binder distribution is determined via various methods to confirm differences in binder homogeneity as a function of both solvent and drying temperature. Identified is the large difference in the efficiency in which the heat is used as well as an ideal drying temperature for both aqueous and non‐aqueous processed cathodes. Also identified is the increased sensitivity to processing temperature for aqueous processed electrodes compared to non‐aqueous processed counterparts, pointing to the possibility of tuned drying regimes which would capitalize on the potential cost savings of aqueous processing for cathodes.

25 ENERGY STORAGE↗

ARJUNA: An Electrochemical Interface Mapping Probe for Solid-State Batteries

Solid-state batteries (SSBs) are promising candidates for next-generation energy storage, although their performance can be compromised by interfacial heterogeneity within the electrolyte. Furthermore, ensuring the quality of large form-factors electrolyte film is crucial for establishing a robust manufacturing platform for solid-state batteries. Herein, we report on the use of ARJUNA, an electrochemical interface mapping system, to characterize heterogeneities at solid electrolyte interfaces and to serve as a quality control system for SSB manufacturing. In addition to spatial mapping, the proposed system can also probe the interface behavior as a function of pressure and temperature. We present the operating principle, design, instrumentation, and evaluation of the system alongside a typical hybrid solid electrolyte produced using two common manufacturing processes. This report showcases the capability of ARJUNA to probe the heterogeneity and quality of processed solid electrolyte films.

25 ENERGY STORAGE↗

Nanoscale Ion Transport Enhances Conductivity in Solid Polymer-Ceramic Lithium Electrolytes

The predictive design of flexible and solvent-free polymer electrolytes for solid-state batteries requires an understanding of the fundamental principles governing the ion transport. In this work, we establish a correlation among the composite structures, polymer segmental dynamics, and lithium ion (Li + ) transport in a ceramic-polymer composite. Elucidating this structure–property relationship will allow tailoring of the Li + conductivity by optimizing the macroscopic electrochemical stability of the electrolyte. The ion dissociation from the slow polymer segmental dynamics was found to be enhanced by controlling the morphology and functionality of the polymer/ceramic interface. The chemical structure of the Li + salt in the composite electrolyte was correlated with the size of the ionic cluster domains, the conductivity mechanism, and the electrochemical stability of the electrolyte. Polyethylene oxide (PEO) filled with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) or lithium bis(fluorosulfonyl) imide (LiFSI) salts was used as a matrix. A garnet electrolyte, aluminum substituted lithium lanthanum zirconium oxide (Al-LLZO) with a planar geometry, was used for the ceramic nanoparticle moieties. Further, the dynamics of the strongly bound and highly mobile Li + were investigated using dielectric relaxation spectroscopy. The incorporation of the Al-LLZO platelets increased the number density of more mobile Li + . The structure of the nanoscale ion-agglomeration was investigated by small-angle X-ray scattering, while molecular dynamics (MD) simulation studies were conducted to obtain the fundamental mechanism of the decorrelation of the Li + in the LiTFSI and LiFSI salts from the long PEO chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗

A lightweight and metal-free current collector for battery anode applications

The requirement for high energy density batteries is driving the development of high-capacity electrode materials while reducing the amount of inactive battery components such as separators, binders, and current collectors. Though current collectors are an inactive component, they are still required for successful working of a battery cell. Conventional current collectors include aluminum foil for cathode and copper foil for anode. Copper foil is quite heavy (8.7 mg/cm 2 ) for 10μm thickness. Therefore, there is a need for a lightweight current collector for anode applications. In this work, a metal-free current collector comprised of aligned carbon fiber (CFs) layer filled with carbon nanotubes (CNTs) mixed in polymer (P) is developed to be used as a current collector for anodes. Further, anodes coated on the CF-CNT-P showed lower charge transfer resistance and improved rate capability compared with the anodes fabricated on conventional copper foil-based current collectors. The CF-CNT-P are lighter (≈1.5 mg/cm 2 ) than the commonly used copper foil (8.7 mg/cm 2 ), which will increase the gravimetric energy density.

25 ENERGY STORAGE↗

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗

High-throughput and high-performance lithium-ion batteries via dry processing

A scalable powder-to-electrode dry processing strategy mainly based on powder dry mixing and rolling/calendering is rationally designed. The dry processed electrodes show lower tortuosity compared to that of conventional slurry-based electrodes. The dry-processed high-loading graphite anodes (6.6 mAh cm -2 ) and LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes (6.0 mAh cm -2 ) exhibit promising electrochemical performance in half-cells and full-cells. The full-cells with both electrodes from dry processing demonstrates superb rate performance to their counterpart with conventional slurry-based electrodes and delivers of capacity retentions of 74.1 % and 63.6 % over 400 and 800 cycles, respectively. Notably, the initial Coulombic efficiency of the dry processed graphite anodes is low ascribed to polytetrafluoroethylene binder. Finally, the results suggest that dry processing is promising for future lithium-ion battery manufacturing and also pinpoint the needs of modification for the polytetrafluoroethylene binder in the graphite anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhancing the Electrochemical Performance of Aqueous Processed Li-Ion Cathodes with Silicon Oxide Coatings

Lithium-ion battery cathode materials suffer from bulk and interfacial degradation issues, which negatively affect their electrochemical performance. Oxide coatings can mitigate some of these problems and improve electrochemical performance. However, current coating strategies have low throughput, are expensive, and have limited applicability. In this article, we describe a low-cost and scalable strategy for applying oxide coatings on cathode materials. Here, we report synergistic effects of these oxide coatings on the performance of aqueously processed cathodes in cells. The SiO 2 coating strategy developed herein improved mechanical, chemical, and electrochemical performance of aqueously processed Ni-, Mn- and Co-based cathodes. This strategy can be used on a variety of cathodes to improve the performance of aqueously processed Li-ion cells.

25 ENERGY STORAGE↗

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗

Review—Electrospun Inorganic Solid-State Electrolyte Fibers for Battery Applications

Inorganic solid-state electrolytes (SSEs), especially Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for all solid-state batteries. Generally, SSEs are synthesized by solid-state reactions at high temperatures. The high temperature required to synthesize useful polymorphs (e.g., cubic phase, in the case of LLZO) increases their production cost. To lower the synthesis temperature, several approaches, including doping and crystallite size control via sol-gel processes, have been explored. Recently, electrospinning was used to synthesize the inorganic SSE fibers to control the crystallite size and lower the calcination temperature. Several publications followed that investigated the properties of fibers and demonstrated the use of these fibers in inorganic-polymer composite SSEs. This paper presents a concise discussion of electrospinning, the parameters that control fiber morphology, the synthesis of inorganic SSE fibers, the effect of sintering conditions on the fiber morphology and composition, and the recent use of these fibers in making composite SSEs and other battery applications. Additionally, most of the discussion focuses on LLZO, but this paper also discusses applications of other types of electrospun inorganic electrolyte fibers, the challenges of using these fibers, and possible future directions in this research field.

25 ENERGY STORAGE↗

Reduced Graphene Oxide Aerogels with Functionalization-Mediated Disordered Stacking for Sodium-Ion Batteries

Surface modified reduced graphene oxide (rGO) aerogels were synthesized using the hydrothermal method. Ethylene diamine (EDA) and α-cyclodextrin (CD) were used to functionalize the surface of the graphene oxide layers. The oxygen reduction and surface modification occurred in-situ during the hydrothermal self-assembly process. The chemical functionality and structure of the resulting ethylene diamine modified (rGO-EDA) and cyclodextrin modified (rGO-CD) aerogels as well as of the pristine unmodified rGO aerogel were studied using XPS, SEM, XRD, and SANS techniques. The overall surface composition showed a significant decrease in the oxygen content for all synthesized aerogels. The surface modified aerogels were characterized by a disordered stacking of the assembled rGO layers. The surface functionalities resulted in a broad distribution of the interlayer spacing and introduced structural heterogeneities. Such disordered structures can enable a better adsorption mechanism of the sodium ions. Coin cells based on the synthesized aerogels and sodium metal were assembled and tested at several charge and discharge rates. The correlation between the surface functionality of the rGO, the induced structural heterogeneities due to the disordered stacking, and the electrochemical performance of sodium-ion batteries were investigated. Operando XRD measurements were carried out during the battery cycling to investigate the adsorption or intercalation nature of the sodiation mechanism.

25 ENERGY STORAGE↗

Nanostructured ligament and fiber Al–doped Li 7 La 3 Zr 2 O 12 scaffolds to mediate cathode-electrolyte interface chemistry

In this study, scaffold structures of electrospun aluminum–substituted lithium lanthanum zirconate Li 7 La 3 Zr 2 O 12 (Al-LLZO) were synthesized and used as an additive in a LiNi 0.6 Mn 0.2 Co 0.2 O 2 composite cathode. The scaffolds were crystalized in the cubic phase after calcination at 700 °C. The Al-LLZO scaffold morphology was dependent on the precursor formulation (aqueous and dimethylformamide. The aqueous precursors resulted in scaffolds of densely coalesced ligaments, whereas the dimethylformamide precursors resulted in high–aspect ratio nanofiber scaffolds. The long-term cycling stability and rate performance of the cells were found to depend on the Al-LLZO scaffold morphology. The uniformly dispersed Al-LLZO fibers resulted in a more stable cathode electrolyte interface formation through the reduced decomposition of the LiPF 6 salt during cycling, resulting in a better high-rate and long-term cycling performance.

25 ENERGY STORAGE↗

Solution-derived monolithic thin films with low adhesion surface

Nanostructured thin films were synthesized using a silica-based sol-gel method. The morphology of the films was tailored by controlling the hydrolysis and crosslinking mechanisms of the tetraethyl orthosilicate precursor. Silica nanoparticle self-assembled structures and linear silica chains were crosslinked and formed monolithic nanostructured films. The self-assembly mechanism was investigated using coarse-grained molecular dynamic simulation. Three nanostructured configurations were synthesized and studied to optimize the surface features of the films and minimize the adhesion of sand particles. Surface microscopy imaging and adhesion force measurements using atomic force microscopy with an attached silica particle on the cantilever tip were performed to correlate the adhesion force and the surface structure. The solar specular reflectance of coated solar mirror samples was measured across the solar spectrum before and after the soiling test of the samples. The mechanical properties of the thin films were evaluated using nanoindentation measurements on coated substrates. Here, the solution-derived thin film coatings can provide anti-soiling protection of solar glass in desert environments and increase the efficiency of photovoltaic and concentrated solar power installations.

42 ENGINEERING↗