Search NASA⌕ Search

Engineering topics

Pollock, Tresa

Publications and source records attributed to Pollock, Tresa.

Resolving crystallographic geometrically necessary dislocations in three dimensions in a hexagonal close packed titanium alloy

Abstract Geometrically necessary dislocation (GND) content is measured from mm 3 -scaled Ti7Al three-dimensional (3D) microstructural data using a theory extended for hexagonal close packed crystals, which accounts for basal, prismatic and pyramidal ⟨ c + a ⟩ type dislocation content. The Ti7Al samples have been mechanically pre-strained to two different strain levels, and will then be strained along the same axis in uniaxial tension during simulation. Both inter- and intragranular GNDs across the microstructures have been characterized, with a large contribution of pyramidal ⟨ c + a ⟩ GNDs, consistent with the relative slip activity involved in pre-straining. The spatially resolved crystallographic GND distributions within the 3D microstructures are used to instantiate a microstructure model for forward modeling deformation simulations by a dislocation density hardening elasto-viscoplastic fast Fourier transform framework. Coarsening the voxel resolution during the initial microstructure construction procedure is shown to strongly impact both the magnitude and spatial distribution of the GNDs and in turn the forward deformation response of the pre-strained material. This study indicates that the voxel resolution desired when transferring from measured to model microstructures need not only be proportionally scaled with the microstructure but also sufficiently fine to capture the subgranular orientation gradients that may already be present in the material.

Materials Science↗

Hierarchical microstructures: a potential route to enhanced stability in structural materials for advanced nuclear reactors

The drive to increase efficiency in nuclear energy systems is leading to the need for materials that operate at higher temperatures and stress levels for extended periods, while maintaining stable microstructures to ensure their performance is not compromised. A novel route to producing materials that can perform well in such environments is the creation of hierarchical microstructures. A hierarchical microstructure is a microstructure in which features are present at multiple length scales simultaneously. In this work, a hierarchical microstructure is fabricated in a nickel-base superalloy, featuring nanometer-size gamma precipitates inside larger gamma-prime particles, which are in turn embedded in the gamma matrix phase. The hierarchical features of the microstructure lead to enhanced stability of the gamma-prime precipitates during annealing; the particle size does not follow the expected t^(1/3) growth law predicted by the classic LSW theory. Phase-field simulations are used to understand the unexpected stability of the gamma-prime precipitates.

36 - MATERIALS SCIENCE↗

In Situ X-ray Radiography and Computational Modeling to Predict Grain Morphology in $\beta$-Titanium during Simulated Additive Manufacturing

The continued development of metal additive manufacturing (AM) has expanded the engineering metallic alloys for which these processes may be applied, including beta-titanium alloys with desirable strength-to-density ratios. To understand the response of beta-titanium alloys to AM processing, solidification and microstructure evolution needs to be investigated. In particular, thermal gradients (Gs) and solidification velocities (Vs) experienced during AM are needed to link processing to microstructure development, including the columnar-to-equiaxed transition (CET). In this work, in situ synchrotron X-ray radiography of the beta-titanium alloy Ti-10V-2Fe-3Al (wt.%) (Ti-1023) during simulated laser-powder bed fusion (L-PBF) was performed at the Advanced Photon Source at Argonne National Laboratory, allowing for direct determination of Vs. Two different computational modeling tools, SYSWELD and FLOW-3D, were utilized to investigate the solidification conditions of spot and raster melt scenarios. The predicted Vs obtained from both pieces of computational software exhibited good agreement with those obtained from in situ synchrotron X-ray radiography measurements. The model that accounted for fluid flow also showed the ability to predict trends unobservable in the in situ synchrotron X-ray radiography, but are known to occur during rapid solidification. A CET model for Ti-1023 was also developed using the Kurz–Giovanola–Trivedi model, which allowed modeled Gs and Vs to be compared in the context of predicted grain morphologies. Both pieces of software were in agreement for morphology predictions of spot-melts, but drastically differed for raster predictions. The discrepancy is attributable to the difference in accounting for fluid flow, resulting in magnitude-different values of Gs for similar Vs.

36 MATERIALS SCIENCE↗

3D Characterization of the Columnar-to-Equiaxed Transition in Additively Manufactured Inconel 718

Additive manufacturing (AM) provides enormous processing flexibility, enabling novel part geometries and optimized designs. Access to a local heat source further permits the potential for local microstructure control on the scale of individual melt pools, which can enable local control of part properties. In order to design tailored processing strategies for target microstructures, models predicting the columnar-to-equiaxed transition must be extended to the high solidification velocities and complex thermal histories present in AM. Here, we combine 3D characterization with advanced modeling techniques to develop a more complete understanding of the solidification process and evolution of microstructure during electron beam melting (EBM) of Inconel 718. Full calibration of existing microstructure prediction models demonstrates the differences between AM processes and more conventional welding techniques, underlying the need for accurate determination of key parameters that can only be measured directly in 3D. The ability to combine multisensor data in a consistent 3D framework via data fusion algorithms is essential to fully leverage these advanced characterization approaches. Thermal modeling provides insight on microstructure development within isolated solidification events and demonstrates the role of Marangoni effects on controlling solidification behavior.

Polonsky, Andrew↗

New frontiers for the materials genome initiative

The Materials Genome Initiative (MGI) advanced a new paradigm for materials discovery and design, namely that the pace of new materials deployment could be accelerated through complementary efforts in theory, computation, and experiment. Along with numerous successes, new challenges are inviting researchers to refocus the efforts and approaches that were originally inspired by the MGI. In May 2017, the National Science Foundation sponsored the workshop “Advancing and Accelerating Materials Innovation Through the Synergistic Interaction among Computation, Experiment, and Theory: Opening New Frontiers” to review accomplishments that emerged from investments in science and infrastructure under the MGI, identify scientific opportunities in this new environment, examine how to effectively utilize new materials innovation infrastructure, and discuss challenges in achieving accelerated materials research through the seamless integration of experiment, computation, and theory. This article summarizes key findings from the workshop and provides perspectives that aim to guide the direction of future materials research and its translation into societal impacts.

36 MATERIALS SCIENCE↗