Effects of acoustic treatment on the interior noise of a twin-engine propeller airplane
Explore the source record for details and available documents.
Beyer, T. B.↗
Engineering topics
Pope, L. D.
Publications and source records attributed to Pope, L. D..
Propeller aircraft interior noise model: User's manual for computer program
A computer program entitled PAIN (Propeller Aircraft Interior Noise) has been developed to permit calculation of the sound levels in the cabin of a propeller-driven airplane. The fuselage is modeled as a cylinder with a structurally integral floor, the cabin sidewall and floor being stiffened by ring frames, stringers and floor beams of arbitrary configurations. The cabin interior is covered with acoustic treatment and trim. The propeller noise consists of a series of tones at harmonics of the blade passage frequency. Input data required by the program include the mechanical and acoustical properties of the fuselage structure and sidewall trim. Also, the precise propeller noise signature must be defined on a grid that lies in the fuselage skin. The propeller data are generated with a propeller noise prediction program such as the NASA Langley ANOPP program. The program PAIN permits the calculation of the space-average interior sound levels for the first ten harmonics of a propeller rotating alongside the fuselage. User instructions for PAIN are given in the report. Development of the analytical model is presented in NASA CR 3813.
Wilby, E. G.↗
Effects of acoustic treatment on the interior noise levels of a twin-engine propeller aircraft - Experimental flight results and theoretical predictions
In-flight noise level measurements were made within two cabin configurations of a general aviation business aircraft. The Fairchild Merlin IVC twin-engine aircraft was tested with bare walls and fiberglass insulation and in an executive trim configuration. Narrow-band and octave format data were subjected to analyses which permitted identification of the blade passage harmonics (BPH). Cabin noise level reductions (insertion losses) due to added insulation varied with position in the cabin, the BPH number, cabin pressure, and engine torque. The measurements were closely predicted using the propeller aircraft interior noise (PAIN) mode.
Beyer, T. B.↗
Propeller aircraft interior noise model utilization study and validation
Utilization and validation of a computer program designed for aircraft interior noise prediction is considered. The program, entitled PAIN (an acronym for Propeller Aircraft Interior Noise), permits (in theory) predictions of sound levels inside propeller driven aircraft arising from sidewall transmission. The objective of the work reported was to determine the practicality of making predictions for various airplanes and the extent of the program's capabilities. The ultimate purpose was to discern the quality of predictions for tonal levels inside an aircraft occurring at the propeller blade passage frequency and its harmonics. The effort involved three tasks: (1) program validation through comparisons of predictions with scale-model test results; (2) development of utilization schemes for large (full scale) fuselages; and (3) validation through comparisons of predictions with measurements taken in flight tests on a turboprop aircraft. Findings should enable future users of the program to efficiently undertake and correctly interpret predictions.
Pope, L. D.↗
Propeller aircraft interior noise model
An analytical model was developed to predict the interior noise of propeller-driven aircraft. The fuselage model is that of a cylinder with a structurally-integral floor. The cabin sidewall is stiffened by stringers and ring frames, and the floor by longitudinal beams. The cabin interior is covered with a sidewall treatments consisting of layers of porous material and an impervious trim septum. Representation of the propeller pressure field is utilized as input data in the form of the propeller noise signature at a series of locations on a grid over the fuselage structure. Results obtained from the analytical model are compared with test data measured by NASA in a scale model cylindrical fuselage excited by a model propeller.
Pope, L. D.↗
Aircraft interior noise models - Sidewall trim, stiffened structures, and cabin acoustics with floor partition
As part of the continuing development of an aircraft interior noise prediction model, in which a discrete modal representation and power flow analysis are used, theoretical results are considered for inclusion of sidewall trim, stiffened structures, and cabin acoustics with floor partition. For validation purposes, predictions of the noise reductions for three test articles (a bare ring-stringer stiffened cylinder, an unstiffened cylinder with floor and insulation, and a ring-stringer stiffened cylinder with floor and sidewall trim) are compared with measurements.
Pope, L. D.↗
Analytical and experimental evaluations of Space Shuttle TPS tile vibration response
Analytical studies and laboratory experiments have been performed to evaluate the vibration response of the Space Shuttle Thermal Protection System (TPS) tiles due to the intense rocket generated acoustic noise during lift-off. The TPS tiles are mounted over the exterior of the Space Shuttle Orbiter structure through Strain Isolation Pads (SIP) which protect the tiles from thermal induced shear loads at their interface. The analytical predictions indicate that the response of a typical tile is governed by the structural vibration inputs through the SIP under the tile at frequencies below 250 Hz, and by the direct acoustic excitation over the exterior surface of the tile at frequencies above 250 Hz. An evaluation of the laboratory test data for this same tile, in which conditioned (partial) coherent output spectral analysis procedures were used, leads to exactly the same conclusion. The results demonstrate the power of conditioned spectral analysis procedures in identifying vibration response mechanisms when two or more of the inputs are highly correlated.
Piersol, A. G.↗
Development and validation of preliminary analytical models for aircraft interior noise prediction
Predictions are made of the transmission of sound into an unpressurized and unstiffened cylinder under random and harmonic excitations, in order to validate the preliminary version of an airplane interior noise prediction model which is based on an analysis of the power flow type. The predictions are compared to experimental results, and statistically significant differences between predictions and measurements are found to be primarily due to input data deficiencies. Because the model requires only the value of a simple integral for determining interior spatial coupling, and resonance frequencies to determine frequency coupling, the known dynamics of the fuselage can be utilized without difficulty.
Pope, L. D.↗
Analytical prediction of the interior noise for cylindrical models of aircraft fuselages for prescribed exterior noise fields. Phase 2: Models for sidewall trim, stiffened structures and cabin acoustics with floor partition
An airplane interior noise prediction model is developed to determine the important parameters associated with sound transmission into the interiors of airplanes, and to identify apropriate noise control methods. Models for stiffened structures, and cabin acoustics with floor partition are developed. Validation studies are undertaken using three test articles: a ring stringer stiffened cylinder, an unstiffened cylinder with floor partition, and ring stringer stiffened cylinder with floor partition and sidewall trim. The noise reductions of the three test articles are computed using the heoretical models and compared to measured values. A statistical analysis of the comparison data indicates that there is no bias in the predictions although a substantial random error exists so that a discrepancy of more than five or six dB can be expected for about one out of three predictions.
Pope, L. D.↗
Analytical prediction of the interior noise for cylindrical models of aircraft fuselages for prescribed exterior noise fields. Phase 1: Development and validation of preliminary analytical models
The basic theoretical work required to understand sound transmission into an enclosed space (that is, one closed by the transmitting structure) is developed for random pressure fields and for harmonic (tonal) excitation. The analysis is used to predict the noise reducton of unpressurized unstiffened cylinder, and also the interior response of the cylinder given a tonal (plane wave) excitation. Predictions and measurements are compared and the transmission is analyzed. In addition, results for tonal (harmonic) mechanical excitation are considered.
Pope, L. D.↗
The development of a method for predicting the noise exposure of payloads in the space shuttle orbiter vehicle
The development of an analytical model for the prediction of sound levels in the payload bay of the space shuttle orbiter vehicle is outlined. Formulation of the analytical model and its validation by means of model scale and full scale tests are included. It is shown that the approach used in the development effort has resulted in a prediction procedure which can be expected to give reliable estimates of payload bay sound levels, even when a payload is present. Furthermore, the analytical model has the capability of being readily modified to include other excitations such as turbulent boundary layers and propeller near-field pressures, and to other aerospace vehicles.
Wilby, J. F.↗
Prediction of the acoustic environment in the Space Shuttle payload bay
An analytical model has been developed to predict space-averaged sound levels in the payload bay of the Space Shuttle when the bay is empty or when a payload is present. The model utilizes the power flow concept and takes into account net power flow from the exterior, flow between subvolumes surrounding a payload, and power dissipation in the subvolumes. The characteristics of the model are described and its application to the Spacelab Configuration 1 payload is presented to illustrate the type of results obtained.
Wilby, J. F.↗
Band-limited power flow into enclosures
Equations for the band-limited power flow to a cavity in the low-frequency regime are derived. The total power to cavity is obtained by summing separate calculations of the power from structural modes resonant in the band and power from structural modes resonant below the band. High-frequency relations compatible with the usual statistical energy analysis and generalized to include other excitations in addition to diffuse fields are also provided.
Pope, L. D.↗
Shock transmission in coupled beams and rib stiffened structures
Shock transmission in a simple coupled beam structure and in a ring-stringer stiffened cylinder is investigated experimentally and analytically using wave transmission and statistical energy analysis concepts. The use of the response spectrum to characterize the excitation provided to a simple beam by a force pulse is studied. Analysis of the transmission of a dilatation wave in a periodically stiffened plate indicates that the stiffeners are fairly transparent to the wave, but some of the dilatational energy is scattered into bending at each support.
Pope, L. D.↗