Engineering topics

Popovici, Alexandru

Publications and source records attributed to Popovici, Alexandru.

8 records

NASA NTRS2020

Adaptive Hexapod Simulator Motion Based on Aircraft Stability

This paper determined the feasibility of an adaptive hexapod simulator motion algorithm based on aircraft roll stability. An experiment was conducted that used a transport aircraft model in the Vertical Motion Simulator at NASA Ames Research Center. Eighteen general aviation pilots flew a heading-capture task and a stall task consecutively under four motion configurations: baseline hexapod, adaptive hexapod, optimized hexapod, and full motion. The adaptive motion was more similar to the baseline hexapod motion in the heading-capture task when the aircraft was more stable, and more similar to the optimized hexapod motion in the stall task when the aircraft was more unstable. Pilot motion ratings and task performance in the heading-capture task under the adaptive hexapod motion were more similar to baseline hexapod motion compared to optimized hexapod motion. However, motion ratings and task performance in the stall task under the adaptive motion were not significantly more similar to the optimized hexapod motion compared to baseline hexapod motion. Motion ratings and overall task performance under optimized hexapod motion as opposed to baseline hexapod motion were always more similar to the full motion condition. This paper showed that adaptive motion based on aircraft stability is feasible and can be implemented in a straightforward way. More research is required to test the adaptive motion algorithm in different tasks.

Zaal, Peter M. T.↗

NASA NTRS2018

Time-Varying Manual Control Identification in a Stall Recovery Task Under Different Simulator Motion Conditions

This paper adds data to help the development of simulator motion cueing guidelines for stall recovery training by identifying time-varying manual control behavior in a stall recovery task under different simulator motion conditions. A study was conducted with seventeen general aviation pilots in the NASA Ames Vertical Motion Simulator. Pilots had to follow a flight director through four stages of a high-altitude stall task. A time-varying identification method was used to quantify how pilot manual control parameters change throughout different stages of the task in both roll and pitch. Four motion configurations were used: no motion, generic hexapod motion, enhanced hexapod motion and full motion. Pilot performance was highest for the enhanced hexapod and full motion configurations in both roll and pitch, and the lowest without motion. In the roll axis, the pilot position gain did not significantly change throughout the stall task, but was the lowest for the condition with no motion. The pilot roll velocity gain was significantly different between motion conditions, the largest difference being found close to the stall point. The enhanced hexapod motion condition had the highest pilot roll velocity gain. In the pitch axis, the pilot position gain was significantly different between time segments but not between motion conditions. The pilot pitch velocity gain was highest for the full motion condition and increased close to the stall point, but did not change significantly for the other motion conditions. Overall, pilot control behavior under enhanced hexapod motion was most similar to that under full aircraft motion. This indicates that motion cueing for stall recovery training on hexapod simulators might be improved by using the principles behind the enhanced hexapod motion configuration.

manual control↗

NASA NTRS2018

Time-Varying Manual Control Identification in a Stall Recovery Task under Different Simulator Motion Conditions

This paper adds data to help develop simulator motion guidelines for stall recovery training by identifying time-varying manual control behavior in a stall recovery task under different simulator motion conditions. A study was conducted in the NASA Ames Vertical Motion Simulator, where seventeen general aviation pilots performed a stall recovery task. Pilots had to follow a flight director through four stages of the stall recovery task. A time-varying identification method was used to quantify how pilots weigh position and velocity information throughout different stages of the task, in both roll and pitch. Four motion configurations were used: no motion, generic hexapod motion, enhanced hexapod motion and full motion. Pilot performance was highest for the enhanced hexapod and full motion conditions in both roll and pitch, and the lowest for the condition with no motion. The time-varying identification method revealed that, in the roll axis, pilot position gain did not significantly change between time segments, but was the lowest for the condition with no motion. The pilot velocity gain was significantly different between motion conditions, the largest difference being found at the beginning of the stall. The enhanced hexapod motion condition had the highest pilot velocity gain. In the pitch axis, the pilot position gain was significantly different between time segments but not between motion conditions. The pitch pilot velocity gain was highest for the full motion condition and increased at the beginning of the stall, but did not change significantly for the other motion conditions. Overall, pilot control behavior under enhanced hexapod motion was more similar to that under full aircraft motion compared to standard hexapod motion. This indicates that motion cueing on hexapod simulators might be improved for stall recovery training by using the enhanced hexapod motion developed in previous experiments.

stall recovery↗

NASA NTRS2018

Managing Complex Airplane System Failures Through a Structured Assessment of Airplane Capabilities

This report describes an analysis of current transport aircraft system-management displays and the initial development of a set of display concepts for providing information about aircraft system status. The new display concepts are motivated by a shift away from the current approach to aircraft system alerting that reports the status of physical components, and towards displaying the implications for mission capability. Specifically, the proposed display concepts describe transport airplane component failures in terms of operational consequences of aircraft system degradations. The research activity described in this report is an effort to examine the utility of different representations of complex systems and operating environments to support real-time decision making during off-nominal situations. A specific focus is to develop display concepts that provide more highly integrated information to allow pilots to more easily reason about the operational consequences of the off-nominal situations. The work can also serve as a foundational element to autonomy-supported decision making since we are developing ideas for integrating information from the airplane and the operational environment to support decision making.

operational decision making↗

NASA NTRS2017

Effects of Retinal Eccentricity on Human Manual Control

This study investigated the effects of viewing a primary flight display at different retinal eccentricities on human manual control behavior and performance. Ten participants performed a pitch tracking task while looking at a simplified primary flight display at different horizontal and vertical retinal eccentricities, and with two different controlled dynamics. Tracking performance declined at higher eccentricity angles and participants behaved more nonlinearly. The visual error rate gain increased with eccentricity for single-integrator-like controlled dynamics, but decreased for double-integrator-like dynamics. Participants' visual time delay was up to 100 ms higher at the highest horizontal eccentricity compared to foveal viewing. Overall, vertical eccentricity had a larger impact than horizontal eccentricity on most of the human manual control parameters and performance. Results might be useful in the design of displays and procedures for critical flight conditions such as in an aerodynamic stall.

system identification↗

NASA NTRS2017

Dual Extended Kalman Filter for the Identification of Time-Varying Human Manual Control Behavior

A Dual Extended Kalman Filter was implemented for the identification of time-varying human manual control behavior. Two filters that run concurrently were used, a state filter that estimates the equalization dynamics, and a parameter filter that estimates the neuromuscular parameters and time delay. Time-varying parameters were modeled as a random walk. The filter successfully estimated time-varying human control behavior in both simulated and experimental data. Simple guidelines are proposed for the tuning of the process and measurement covariance matrices and the initial parameter estimates. The tuning was performed on simulation data, and when applied on experimental data, only an increase in measurement process noise power was required in order for the filter to converge and estimate all parameters. A sensitivity analysis to initial parameter estimates showed that the filter is more sensitive to poor initial choices of neuromuscular parameters than equalization parameters, and bad choices for initial parameters can result in divergence, slow convergence, or parameter estimates that do not have a real physical interpretation. The promising results when applied to experimental data, together with its simple tuning and low dimension of the state-space, make the use of the Dual Extended Kalman Filter a viable option for identifying time-varying human control parameters in manual tracking tasks, which could be used in real-time human state monitoring and adaptive human-vehicle haptic interfaces.

manual control↗

NASA NTRS2017

Effects of Eye Measures on Human Controller Remnant and Control Behavior

The aim of the current research was to investigate the possible relation between changes in eye activity parameters, variations in human remnant at the perceptual level and changes in human operator model parameters. Fourteen subjects performed a pitch tracking task, in which the display brightness was varied by changing the background color around a simplified primary flight display, in order to create a controlled, quasilinear change in the pupil diameter through the pupillary light reflex. Pupil diameter, blink, eye opening, and opening and closing amplitudes and speeds were recorded using an eye tracker. Participants controlled single integrator-like and double integrator-like dynamics. The variation in pupil diameter did not introduce significant differences in neither remnant characteristics nor the human operator model parameters. An interesting effect occurred in the human controller’s time delay for the single integrator task, where the time delay was significantly higher for the darkest brightness compared to the other levels of brightness. This effect was not observed for the double integrator dynamics. Data suggested that the more difficult controlled dynamics induced a squinting effect, visible in smaller eye opening, and smaller eye opening and closing amplitudes. These results suggest that performance, and control behavior are invariant to the display brightness. Moreover, monitoring changes in the eye activity could represent a method of predicting variations in human remnant characteristics and human controller model parameters, introduced by task difficulty.

Eye tracking↗

NASA NTRS2015

Effects of False Tilt Cues on the Training of Manual Roll Control Skills

This paper describes a transfer-of-training study performed in the NASA Ames Vertica lMotion Simulator. The purpose of the study was to investigate the effect of false tilt cues on training and transfer of training of manual roll control skills. Of specific interest were the skills needed to control unstable roll dynamics of a mid-size transport aircraft close to the stall point. Nineteen general aviation pilots trained on a roll control task with one of three motion conditions: no motion, roll motion only, or reduced coordinated roll motion. All pilots transferred to full coordinated roll motion in the transfer session. A novel multimodal pilot model identification technique was successfully applied to characterize how pilots' use of visual and motion cues changed over the course of training and after transfer. Pilots who trained with uncoordinated roll motion had significantly higher performance during training and after transfer, even though they experienced the false tilt cues. Furthermore, pilot control behavior significantly changed during the two sessions, as indicated by increasing visual and motion gains, and decreasing lead time constants. Pilots training without motion showed higher learning rates after transfer to the full coordinated roll motion case.

simulators↗