Search NASA⌕ Search

Engineering topics

Pourboghrat, Farhang

Publications and source records attributed to Pourboghrat, Farhang.

At least 19 records

Convergent laser beam shapes: Unveiling the dynamics of Laser-induced elastic waves in composite materials

Overcoming the low signal-to-noise ratio (SNR) in laser ultrasonic testing of composite materials remains a significant challenge. Current efforts focus on enhancing SNR by inserting more energy into the material through temporal and/or spatial modulation of the laser beam. However, potential SNR improvements through wave convergence and wave energy manipulation have been overlooked. This paper addresses this gap by demonstrating the convergence of different wave types to a designated point and by showing the feasibility of directing absorbed laser energy into a specific wave type through spatial modulation of the laser beam. To achieve this, mathematical expressions for the convergent laser beams are derived. Various laser beam profiles are then introduced to the thermoelastic equations and solved using the finite element method. The sample under investigation is a transversely isotropic unidirectional carbon fiber reinforced plastic, characterized by anisotropic thermal expansion coefficients and thermal conductivities. Results reveal pronounced convergence of the intended wave type at the center due to laser beam shaping. This study showcases the ability to direct absorbed laser energy toward a specific wave type through spatial modulation of the laser beam and highlights the role of material anisotropy in energy focusing.

composite materials↗

Design, performance, and cost savings of using GF-PC additively manufactured tooling for stamping of HSS 590 sheet metal

Conventional sheet metal forming tooling in the automotive industry is made up of hardened steel and used for mass-production. Prototype tooling made of metal is durable, but it is only used for a small number of parts despite its high cost, contributing heavily to the vehicle development cost. Additive Manufacturing (AM) offers a low-cost alternative for fabricating tooling suitable for low-volume production. Here, this study investigates the feasibility of using AM polymer composite tooling for the stamping of 1.5mm thickness HSS 590 steel sheets through a two-pronged approach – experimental and numerical analysis. Sheet metal stamping experiments were conducted with glass fiber reinforced polycarbonate (GF-PC) AM polymer tooling and their performance was evaluated based on various metrics such as tool deformation and part accuracy. Finite element simulations of the stamping process were performed, which accurately captured the tool deformations seen in experiments with the use of anisotropic material models. The effective use of simulations in optimizing process parameters to achieve the desired final part geometry is also demonstrated. The GF-PC AM polymer composite tooling was found to be well suited for low volume production applications with potential cost savings.

36 MATERIALS SCIENCE↗

Prediction of softening kinetics and recrystallization texture in non-isothermally annealed bulged tubes using CPFEM and CA models

A hierarchically coupled cellular automata (CA) model, crystal plasticity finite element method (CPFEM), and thermal finite element (FE) model is developed to predict the softening kinetics of the bulged steel tube during non-isothermal annealing. Through the developed model, the kinetics of softening mechanisms including static recovery (SRV) and static recrystallization (SRX), as well as the recrystallization texture are predicted. Later, the Johnson-Mehl-Avrami-Kohnogorov (JMAK) model based on the predicted SRX data is developed to interpret the recrystallization behavior of the material. To perform this study, diverse experimental tests including tube hydroforming (THF), annealing, uniaxial tensile test, hardness test, as well as microstructure observations through optical microscopy and Electron Backscatter Diffraction (EBSD) tests on steel tube are performed. The obtained experimental data are utilized to calibrate and verify the implemented CPFEM model for simulation of THF process, thermal FE model for prediction of the local temperature over annealing time, and CA algorithm for modeling of the softening kinetics and texture evolution throughout the annealing process. The study shows that the predicted deformation characteristics, softening kinetics, recrystallization texture and temperature profile during non-isothermal annealing are in good agreement with experimental data. During the annealing process, a total of four stages for the kinetics of softening mechanisms is observed: No softening; SRV only; SRV dominant; and SRX dominant. During the progress of SRX, the behavior of recrystallization is abruptly changed, confirming that two different mechanisms are controlling the kinetics of transformation.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of the AA7075 Tube Fabricated using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) experimental setup and tooling were adopted for extruding thin-walled AA7075 aluminum tube from as-cast non-homogenized billet material in a single run. The mechanical and microstructural characterizations were performed on the extrudate in the as-extruded condition without subsequent heat treating. It was shown that the ShAPE process developed a significantly refined microstructure with uniform and almost equiaxed grain structure on both hoop and axial cross-sections of the extrudate as well as through the thickness of the material. The pole figures and inverse pole figures of the EBSD data showed an strong shear texture development, and it was found out that axial shear is the dominant deformation mechanism in the regions near the inner surface of the tube, while combined axial and torsional shears are the two dominant modes of deformation near the outer surface of the extrudate. As for the mechanical properties, there was an increase of 150% and 73% in the yield and ultimate strengths of the tube produced using ShAPE process, respectively, and a 18% decrease in maximum uniform plastic elongation compared to the conventionally extruded AA7075-O tube.

Shear Assisted Processing and Extrusion, Friction ↗

The Effect of Process History on Grain Boundaries and Dislocation Substructures on Functional Properties of Nb for SRF Cavities: Plastic Formability and Microstructural Evolution. Final report

While much progress has been made in improving the performance of cavities in the past decade, reproducible performance remains elusive. This renewal of “The cost of grain boundaries on the performance of superconducting cavities” examines in further depth the interactions between forming and annealing processes and functional performance at the scale of dislocation substructure and grain boundaries. There are five tasks identified in the renewal, which are: Characterization / analysis of current cavity technology: Effect of deformation, heat treatment, surface treatments, and residual damage on cavity function (Lee and Bieler) Characterization of dislocation mechanisms in single and bicrystals (Bieler) Quantifying effects of impurities and deformation mechanisms in Nb using density functional theory calculations (Solanki) Crystal plasticity constitutive model development (Pourboghrat and Eisenlohr) Modeling and measuring thermal conductivity in thin layers (Wright)

36 MATERIALS SCIENCE↗

An Evolutionary Yield Function Model Based on Plastic Work and Non-Associated Flow Rule

A constitutive law was developed based on the evolutionary yield function to account for the evolution of anisotropy induced by the plastic deformation. For the effective description of anisotropy, the yield stress function and plastic potential were separately defined based on the non-associated flow rule. In particular, for the description of the equivalent status, the accumulated plastic work was employed as an alternative to the accumulated plastic strain. Numerical formulations based on the plastic work were also derived in case the hardening rule, as well as the evolution of the plastic potential and yield stress function, were defined in terms of the plastic work. The developed constitutive law was characterized using the mechanical properties of the multi-phase BAO QP980 steel and niobium sheets at room temperature. From the uniaxial tension tests and the balanced biaxial tension test, separate sets of anisotropic coefficients for each of the plastic potential and yield stress functions were obtained as a function of the plastic work. By comparing with non-evolving yield functions, the importance of the developed constitutive law to properly describe the evolution of the plastic potential and yield function were validated.

Park, Taejoon↗

Deformation mechanisms, defects, heat treatment, and thermal conductivity in large grain niobium

The physical and mechanical metallurgy underlying fabrication of large grain cavities for superconducting radio frequency accelerators is summarized, based on research of 1) grain orientations in ingots, 2) a metallurgical assessment of processing a large grain single cell cavity and a tube, 3) assessment of slip behavior of single crystal tensile samples extracted from a high purity ingot slice before and after annealing at 800 °C / 2 h, 4) development of crystal plasticity models based upon the single crystal experiments, and 5) assessment of how thermal conductivity is affected by strain, heat treatment, and exposure to hydrogen. Because of the large grains, the plastic anisotropy of deformation is exaggerated, and heterogeneous strains and localized defects are present to a much greater degree than expected in polycrystalline material, making it highly desirable to computationally anticipate potential forming problems before manufacturing cavities.

36 MATERIALS SCIENCE↗