Engineering topics

Powell, R. W.

Publications and source records attributed to Powell, R. W..

At least 37 records · Page 2

NASA NTRS1984

Effect of aerodynamic and angle-of-attack uncertainties on the blended entry flight control system of the Space Shuttle from Mach 10 to 2.5

A six-degree-of-freedom simulation analysis has been performed for the Space Shuttle Orbiter during entry from Mach 10 to 2.5 with realistic off-nominal conditions using the entry flight control system specified in May 1978. The off-nominal conditions included the following: (1) aerodynamic uncertainties, (2) an error in deriving the angle of attack from onboard instrumentation, (3) the failure of two of the four reaction control-system thrusters on each side, and (4) a lateral center-of-gravity offset. With combinations of the above off-nominal conditions, the control system performed satisfactorily with a few exceptions. The cases that did not exhibit satisfactory performance displayed the following main weaknesses. Marginal performance was exhibited at hypersonic speeds with a sensed angle-of-attack error of 4 deg. At supersonic speeds the system tended to be oscillatory, and the system diverged for several cases because of the inability to hold lateral trim. Several system modifications were suggested to help solve these problems and to maximize safety on the first flight: alter the elevon-trim and speed-brake schedules, delay switching to rudder trim until the rudder effectiveness is adequate, and reduce the overall rudder loop gain. These and other modifications were incorporated in a flight-control-system redesign in May 1979.

Stone, H. W.↗

NASA NTRS1984

Performance assessment of aero-assisted orbital transfer vehicles

Aero-assisted orbital transfer vehicles are analyzed. The aerodynamic characteristics over the flight profile and three- and six-degree-of-freedom performance analyses were determined. The important results, to date, are: (1) the aerodynamic preliminary analysis system, an interactive computer program, used to predict the aerodynamics (performance, stability, and control) for these vehicles; (2) the performance capability, e.g., maximum inclination change, maximum heating rate, and maximum sensed acceleration, can be determined using continuum aerodynamics only; (3) guidance schemes can be developed that allow for errors in atmospheric density prediction, mispredicted trim angle of attack, and off-nominal atmospheric interface conditions, even for vehicles with a low lift-to-drag ratio; and (4) multiple pass trajectories can be used to reduce the maximum heating rate.

Powell, R. W.↗

NASA NTRS1984

Performance evaluation of the atmospheric phase of aeromaneuvering orbital transfer vehicles

Studies are underway to design reusable orbital transfer vehicles that would be used to transfer payloads from low-earth orbit to higher orbits and return. One promising concept is to use an atmospheric pass on the return leg to reduce the amount of fuel for the mission. This paper discusses a six-degree-of-freedom simulation analysis for two configurations, a low-lift-to-drag ratio configuration and a medium-lift-to-drag ratio configuration using both a predictive guidance technique and an adaptive guidance technique. Both guidance schemes were evaluated using the 1962 standard atmosphere and three atmospheres that had been derived from three entries of the Space Shuttle. The predictive technique requires less reaction control system activity for both configurations, but because of the limited number of updates and because each update used the 1962 standard atmosphere, the adaptive technique produces more accurate exit conditions.

Powell, R. W.↗

NASA NTRS1984

Evaluation of the aerodynamic control of the Space Shuttle orbiter and tip-fin controllers

A feasibility study to assess the benefits/penalties of installing tip-fin controllers on the Space Shuttle orbiter has been conducted. The results from the aerodynamic and stability and control assessment of this study are presented. These results show that using tip-fin controllers with the centerline vertical tail removed provides adequate control for entry. The orbiter basic maneuvering capability is maintained, and symmetrical deflection of the controllers provides adequate speedbrake authority for energy management. Gust analyses of the orbiter with the tip-fin controller configuration have demonstrated no compromise of existing cross-wind landing capability. Six-degree-of-freedom simulations have shown the tip-fin controllers can provide adequate control for entry with no degradation in vehicle capability.

Powell, R. W.↗

NASA NTRS1983

Ascent performance and abort analysis for a Future Space Transportation System

The Future Space Transportation System (FSTS) study was conducted by the NASA Langley Research Center to identify the technology requirements for concepts that will replace the Space Shuttle in the post 2000 time frame. The configuration chosen for the study is a two-stage, fully reusable, vertical liftoff, and horizontal landing system with a 150,000 lb. payload capability. The two stages are burned in parallel with the booster providing all the propellant until staging, which results in a large lateral c.g. movement. Nominally, the booster stages at Mach 3 and glides back to the launch site. Because of the large lateral c.g. travel, a scheme to trim the vehicle until staging occurred was developed that used both gimballing and throttling of the engines. Preliminary booster aerodynamics were determined, and the booster glideback trajectory was analyzed with and without winds. Finally, a preliminary abort analysis was conducted for each stage.

Naftel, J. C.↗

NASA NTRS1983

Booster and orbiter configurations

In the recent Future Space Transportation System (FSFS) study, a mission model was selected and a baseline vehicle which best met model requirements was shaped. This baseline was then analyzed for flight performance, structural and subsystem weight, and operation. Figures related to a payload of 150,000 lb in a 20-ft-diam by 90-ft-long envelope became the baseline. The existence of both space-based orbital transfer vehicles (OTVs) and a space station was assumed, taking into account a transfer of the payload from the launch vehicle to OTVs at the space station for final delivery to geosynchronous orbit (GEO). A computer-aided engineering system called Aerospace Vehicle Interactive Design (AVID) was employed in connection with baseline vehicle development. It was found that approximately three-fifth of the payload weight would be cryogenic propellants for OTVs. Attention is given to problems regarding the packaging of cryogenic tankage, a payload shroud, and studies of staging for two different booster propulsion units.

Wilhite, A. W.↗

NASA NTRS1983

Space Shuttle third flight /STS-3/ entry RCS analysis

Flight data obtained from three Space Transportation System orbiter entries (STS-1, 2, and 3) are processed and analyzed to determine the roll interactions caused by the firing of the entry reaction control system (RCS). Comparisons between the flight-derived parameters and the predicted derivatives without interaction effects are made. The flight-derived RCS Plume flow-field interaction effects are independently deduced by direct integration of the incremental changes in the wing upper surface pressures induced by RCS side thruster firings. The separately obtained interaction effects are compared to the predicted values and the differences are discussed.

Scallion, W. I.↗

NASA NTRS1981

Application of a tip-fin controller to the Shuttle Orbiter for improved yaw control

Aerodynamic and flight control analyses have shown that the application of the tip-fin controller and removal of the centerline vertical tail does not produce improved flyability of the Shuttle Orbiter in the supersonic speed regime. Preliminary design studies show that removal of the centerline vertical tail and the installation of tip-fin controllers could result in savings up to 900 kg. It is also shown that the reaction control system could be deactivated much sooner than it is possible with the present nominal orbiter configuration.

Powell, R. W.↗

NASA NTRS1980

Development of the reentry flight dynamics simulator for evaluation of space shuttle orbiter entry systems

A nonlinear, six degree of freedom, digital computer simulation of a vehicle which has constant mass properties and whose attitudes are controlled by both aerodynamic surfaces and reaction control system thrusters was developed. A rotating, oblate Earth model was used to describe the gravitational forces which affect long duration Earth entry trajectories. The program is executed in a nonreal time mode or connected to a simulation cockpit to conduct piloted and autopilot studies. The program guidance and control software used by the space shuttle orbiter for its descent from approximately 121.9 km to touchdown on the runway.

Rowell, L. F.↗

NASA NTRS1980

Analysis of space shuttle orbiter entry dynamics from Mach 10 to Mach 2.5 with the November 1976 flight control system

A six-degree-of-freedom simulation analysis was performed for the space shuttle orbiter entry from Mach 10 to Mach 2.5 with realistic off-nominal conditions using the flight control system referred to as the November 1976 Integrated Digital Autopilot. The off-nominal conditions included: (1) aerodynamic uncertainties in extrapolating from wind tunnel of flight characteristics, (2) error in deriving angle of attack from onboard instrumentation, (3) failure of two of the four reaction control-system thrusters on each side (design specification), and (4) lateral center-of-gravity offset. Many combinations of these off-nominal conditions resulted in a loss of the orbiter. Control-system modifications were identified to prevent this possibility.

Powell, R. W.↗

NASA NTRS1979

The results of studies to determine the impact of far-aft center-of-gravity locations on the design of a single-stage-to-orbit vehicle system

Aft center-of-gravity locations dictated by the large number of rocket engines required has been a continuing problem of single-stage-to-orbit vehicles. Recent work at Langley has demonstrated that these aft center-of-gravity problems become more pronounced for the proposed heavy-lift mission, creating some unique design problems for both the SSTO and staged vehicle systems. During the course of this study, an effort was made to bring together automated vehicle design, wind-tunnel tests, and flight control analyses to assess the impact of longitudinal and lateral-directional instability, and control philosophy on entry vehicle design technology.

Freeman, D. C., Jr.↗

NASA NTRS1978

Effects of atmospheric structure on radiative heating for Jupiter entry probe

New estimates of the radiative heat load to a Jupiter entry probe have been obtained for revised models of Jupiter's atmosphere based on the latest data from Pioneer 10 and 11 missions and earth-based experiments. The new estimates of the radiative heat load are compared with results obtained for the previous atmospheric models. The changes in Jupiter's atmospheric models cause a substantial reduction in the radiative heat load for the atmosphere denoted as 'cool', but only moderate reductions for the atmospheres denoted as 'nominal' and 'warm'. Results are also presented showing the effects of inertial entry angle for off-equatorial entries in the revised model atmospheres.

Sutton, K.↗

NASA NTRS1978

The effect of normal atmospheric variability on Space Shuttle Orbiter entry performance

The Space Shuttle Orbiter is controlled during entry by a combination of aerodynamic surfaces composed of elevons, a body flap, and a rudder that flares as a speedbrake, and a reaction control system that uses 16 small rocket thrusters. To determine the effects of realistic atmospheric density variations on reentry, a series of Monte Carlo trajectories were generated for each season. The performance parameters analyzed include maximum hinge moments experienced by the aerodynamic control surfaces, the maximum deflections experienced by the aerodynamic control surfaces, a range of angle-of-sideslip values, maximum dynamic pressure, maximum stagnation point heat rate, and state conditions at touchdown. The results of the investigation indicate that the Orbiter guidance and control systems could tolerate atmospheric variability without failures in the control system hardware.

Powell, R. W.↗

NASA NTRS1977

Entry dynamics of space shuttle orbiter with lateral-directional stability and control uncertainties at supersonic and hypersonic speeds

A six-degree-of-freedom simulation analysis was conducted to examine the effects of the lateral-directional static aerodynamic stability and control uncertainties on the performance of the automatic (no manual inputs) entry-guidance and control systems of the space shuttle orbiter. To establish the acceptable boundaries of the uncertainties, the static aerodynamic characteristics were varied either by applying a multiplier to the aerodynamic parameter or by adding an increment. Control-system modifications were identified that decrease the sensitivity to off-nominal aerodynamics. With these modifications, the acceptable aerodynamic boundaries were determined.

Stone, H. W.↗

NASA NTRS1977

Entry dynamics of space shuttle orbiter with longitudinal stability and control uncertainties at supersonic and hypersonic speeds

A six-degree-of-freedom simulation analysis was conducted to examine the effects of longitudinal static aerodynamic stability and control uncertainties on the performance of the space shuttle orbiter automatic (no manual inputs) entry guidance and control systems. To establish the acceptable boundaries, the static aerodynamic characteristics were varied either by applying a multiplier to the aerodynamic parameter or by adding an increment. With either of two previously identified control system modifications included, the acceptable longitudinal aerodynamic boundaries were determined.

Stone, H. W.↗

NASA NTRS1977

Aileron roll hysteresis effects on entry of space shuttle orbiter

Six-degree-of-freedom simulations of the space shuttle orbiter entry with control hysteresis were conducted on the NASA Langley Research Center interactive simulator known as the automatic reentry flight dynamics simulator. These simulations revealed that the vehicle can tolerate control hysteresis producing a + or - 50 percent change in the nominal aileron roll characteristics and an offset in the nominal characteristics equivalent to a + or - 5 deg aileron deflection with little increase in the reaction control system's fuel consumption.

Powell, R. W.↗

NASA NTRS1977

A real-time digital computer program for the simulation of automatic spacecraft reentries

The automatic reentry flight dynamics simulator, a nonlinear, six-degree-of-freedom simulation, digital computer program, has been developed. The program includes a rotating, oblate earth model for accurate navigation calculations and contains adjustable gains on the aerodynamic stability and control parameters. This program uses a real-time simulation system and is designed to examine entries of vehicles which have constant mass properties whose attitudes are controlled by both aerodynamic surfaces and reaction control thrusters, and which have automatic guidance and control systems. The program has been used to study the space shuttle orbiter entry. This report includes descriptions of the equations of motion used, the control and guidance schemes that were implemented, the program flow and operation, and the hardware involved.

Kaylor, J. T.↗

NASA NTRS1976

An investigation of the effects of mass loss, shape change and real gas aerodynamics on a Jovian atmospheric reconstruction experiment

A survey of the effects of mass loss, shape change and real-gas aerodynamics on a Jovian atmospheric reconstruction experiment is carried out. Techniques used to reconstruct atmospheric profiles from entry probe measurements are discussed and some of the parameters which affect their accuracy are identified. Trajectory analyses and real-gas, radiatively-coupled flow field analyses (which include the effects of mass loss and shape change) are carried out for several candidate probe configurations. From these analyses, uncertainties in the atmospheric reconstruction procedure are estimated. Finally, the prospects for reducing these uncertainties by optimizing probe configuration and by instrumentation of the probe heat shield to measure actual shape change are considered.

Walberg, G. D.↗