Search NASA⌕ Search

Engineering topics

Prasad, C. B.

Publications and source records attributed to Prasad, C. B..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Effects of cutouts on the behavior of symmetric composite laminates subjected to bending and twisting loads

Composite structures are used for a wide variety of aerospace applications. Practical structures contain cutouts and these structures are subjected to in-plane and out-of-plane loading conditions. Structurally efficient designs for composite structures require a thorough understanding of the effects of cutouts on the response of composite plates subjected to inplane or out-of-plane loadings. Most investigations of the behavior of composite plates with cutouts have considered in-plane loadings only. Out-of-plane loadings suchas bending or twisting have received very limited attention. The response of homogeneous plates (e.g., isotropic or orthotropic plates) subjected to bending or twisting moments has been studied analytically. These analyses are for infinite plates and neglect finite-plate effects. Recently, analytical and experimental studies were conducted to determine the effects of cutouts on the response of laminated composite plates subjected to bending moments. No analytical or experimental results are currently available for the effects of cutouts on the response of composite laminates subjected to twisting moments.

Prasad, C. B.↗
NASA NTRS1992

Analysis of multifastener composite joints

A new numerical procedure for determining load proportioning in multiple-hole mechanical joints in composite plates is presented. The joints are loaded in double lap fashion in tension with pins through the holes. The commercial finite-element program ABAQUS is used to predict the load proportioning among holes using two independent plane stress finite-element models, one representing the composite inner lap and one representing the two steel outer laps, interacting through rigid circular surfaces. The circular surfaces effectively represent rigid pins. Load proportioning is predicted for a number of geometries. Excellent correlation with experimental data is obtained. Experimental and computed surface strains are also found to compare well. The assumption of a radial cosine distribution of contact stress between pin and hole is shown to be substantially in error for some holes.

Griffin, O. H., Jr.↗
NASA NTRS1990

A Protection And Detection Surface (PADS) for damage tolerance

A protection and detection surface (PADS) concept was studied for application to composite primary aircraft structures. A Kevlar-epoxy woven face sheet with a Rohacell foam core was found to be the most effective PADS configuration among the configurations evaluated. The weight of the PADS configuration was estimated to be approximately 17 percent of the structural weight. The PADS configuration was bonded to graphite-epoxy base laminates, and up to a 70 percent improvement in compression-after-impact failure strains was observed.

Shuart, M. J.↗
NASA NTRS1990

Analysis and experiments for composite laminates with holes and subjected to 4-point bending

Analytical and experimental results are presented for composite laminates with a hole and subjected to four-point bending. A finite-plate analysis is used to predict moment and strain distributions for six-layer quasi-isotropic laminates and transverse-ply laminates. Experimental data are compared with the analytical results. Experimental and analytical strain results show good agreement for the quasi-isotropic laminates. Failure of the two types of composite laminates is described, and failure strain results are presented as a function of normalized hole diameter. The failure results suggest that the initial failure mechanism for laminates subjected to four-point bending are similar to the initial failure mechanisms for corresponding laminates subjected to uniaxial inplane loadings.

Shuart, M. J.↗
NASA NTRS1989

Effects of transverse shear on large deflection random response of symmetric composite laminates with mixed boundary conditions

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived considering von Karman strains and transverse shear effects. Using a single-mode Galerkin procedure, the nonlinear modal equation is obtained. The direct equivalent linearization method is employed for solution of this equation. The effects of transverse shear on large deflection vibration of laminated plates with mixed boundary support conditions under random excitation are studied. Mean-square deflections and mean-square inplane strains are obtained for symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for plates with two opposing edges simply supported and the remaining edges clamped.

Prasad, C. B.↗
NASA NTRS1989

Moment distributions around holes in symmetric composite laminates subjected to bending moments

An analytical investigation of the effects of holes on the moment distribution of symmetric composite laminates subjected to bending moments is described. A general, closed-form solution for the moment distribution of an infinite anisotropic plate is derived, and this solution is used to determine stress distributions both on the hole boundary and throughout the plate. Results are presented for several composite laminates that have holes and are subjected to either pure bending or cylindrical bending. Laminates with a circular hole or with an elliptical hole are studied. Laminate moment distributions are discussed, and ply stresses are described.

Prasad, C. B.↗
NASA NTRS1988

Large deflection random response of cross-ply laminated plates with elastically restrained edges and initial imperfections

The large deflection random response of symmetrically laminated cross-ply rectangular thin plates subjected to random excitation is studied. The out-of-plane boundary conditions are such that all the edges are rigidly supported against translation, but elastically restrained against rotation. The plate is also assumed to have a small initial imperfection. The assumed membrane boundary conditions are such that all the edges are free from normal and tangential forces in the plane of the plate. Mean-square deflections and mean-square strains are determined for a three-layered cross-ply laminate.

Prasad, C. B.↗
NASA NTRS1987

Multiple-mode large deflection random response of beams with nonlinear damping subjected to acoustic excitation

Multiple-mode nonlinear analysis is carried out for beams subjected to acoustic excitation. Effects of both nonlinear damping and large-deflection are included in the analysis in an attempt to explain the experimental phenomena of aircraft panels excited at high sound pressure levels; that is the broadening of the strain response peaks and the increase of modal frequency. An amplitude dependent nonlinear damping model is used in the anlaysis to study the effects and interactions of multiple modes, nonlinear stiffness and nonlinear damping on the random response of beams. Mean square maximum deflection, mean square maximum strain, and spectral density function of maximum strain for simple supported and clamped beams are obtained. It is shown analytically that nonlinear damping contributes significantly to the broadening of the response peak and to the mean square deflection and strain.

Prasad, C. B.↗
NASA NTRS1987

Influence of large deflection and transverse shear on random response of rectangular symmetric composite laminates to acoustic loads

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived accounting for von Karman strains. The effect of transverse shear is included in the formulation and the rotatory inertia effect is ignored. Using a single-mode Galerkin procedure the nonlinear modal equation is obtained. Direct equivalent linearization is employed. The response of acoustic excitation on moderately thick composite panels is studied. Further, the effects of transverse shear on large deflection vibration of laminates under random excitation are studied. Mean-square deflection and mean-square inplane stresses are obtained for some symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for simply supported plate. The analogous equations for a clamped case are given in the appendix.

Mei, Chuh↗
NASA NTRS1987

Effects of large deflection and transverse shear on response of rectangular symmetric composite laminates subjected to acoustic excitation

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived accounting for von Karman strains. The effect of transverse shear is included in the formulation. Using a single-mode Galerkin procedure, the nonlinear modal equation is obtained. The direct equivalent linearization method is employed for solution of this equation. The response to acoustic excitation of moderately thick composite panels is studied. Further, the effects of transverse shear on large deflection vibration of laminates under random excitation are studied. Mean-square deflections and mean-square inplane stresses are obtained for symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for simply supported plates. The analogous equations for a clamped case are also obtained.

Mei, Chuh↗
NASA NTRS1987

Determination of calibration constants for the hole-drilling residual stress measurement technique applied to orthotropic composites. I - Theoretical considerations

The hole-drilling technique for the measurement of residual stresses using electrical resistance strain gages has been widely used for isotropic materials and has been adopted by the ASTM as a standard method. For thin isotropic plates, with a hole drilled through the thickness, the idealized hole-drilling calibration constants are obtained by making use of the well-known Kirsch's solution. In this paper, an analogous attempt is made to theoretically determine the three idealized hole-drilling calibration constants for thin orthotropic materials by employing Savin's (1961) complex stress function approach.

Prasad, C. B.↗
NASA NTRS1987

Determination of calibration constants for the hole-drilling residual stress measurement technique applied to orthotropic composites. II - Experimental evaluations

The first step in the extension of the semidestructive hole-drilling technique for residual stress measurement to orthotropic composite materials is the determination of the three calibration constants. Attention is presently given to an experimental determination of these calibration constants for a highly orthotropic, unidirectionally-reinforced graphite fiber-reinforced polyimide composite. A comparison of the measured values with theoretically obtained ones shows agreement to be good, in view of the many possible sources of experimental variation.

Prasad, C. B.↗
NASA NTRS1986

Response of symmetric rectangular composite laminates with nonlinear damping subjected to acoustic loading

Effects of both nonlinear damping and large-deflection are included in the analysis in an attempt to explain the experimental phenomena of aircraft panels excited at high sound pressure levels; that is the broadening and flattening out of the strain response peaks and the increasing of the response frequency. A nonlinear damping model is considered in the analysis using a single-mode approach. Root-mean-square (RMS) maximum deflection, RMS strains, spectral density functions of strain, and equivalent linear frequency are obtained for clamped and simply supported rectangular symmetric laminated composite plates. It is demonstrated that nonlinear damping is the one which causes the broadening of the response peaks, and it has great influence on RMS panel deflection, RMS strains, and frequency.

Mei, C.↗
NASA NTRS1986

Effects of nonlinear damping on random response of beams to acoustic loading

Effects of both nonlinear damping and large-deflection are included in the theoretical analysis in an attempt to explain the experimental phenomena of aircraft panels excited at high sound pressure levels; that is the broadening of the strain response peak and the increase of the modal frequency. Two nonlinear damping models are considered in the analysis using a single-mode approach. Mean square maximum deflection, mean square maximum strain, and spectral density function of maximum strain for simply supported and clamped beams are obtained. It is demonstrated that nonlinear damping contributes significantly to the broadening of the response peak and to the mean square maximum deflection and strain.

Mei, C.↗