Search NASA⌕ Search

Engineering topics

Prater, R

Publications and source records attributed to Prater, R.

Contributions of Electron Cyclotron Waves to Performance in Advanced Regimes on DIII-D

High-power electron cyclotron (EC) waves are used to increase performance in several Advanced Tokamak (AT) regimes on DIII-D where there is a simultaneous need for high noninductive current and high beta. In the Quiescent High-confinement mode (QH-mode), a direct measurement of the electron cyclotron current drive (ECCD) profile is made using modulation techniques, and a trapped electron mode (TEM) dominated regime with core T{sub e}>T{sub i} is created. In the 'highq{sub min}' AT scenario, ECCD provides part of the off-axis noninductive current and helps to produce a tearing stable equilibrium. In the hybrid regime, strong central current drive from EC waves and other sources increases the noninductive current fraction to {approx_equal}100%. Surprisingly, the core safety factor remains above unity, meaning good alignment between the current drive profile and the desired plasma current profile is not necessary in this scenario.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in validating gyrokinetic turbulence models against L- and H-mode plasmas

Robust validation of predictive turbulent transport models requires quantitative comparisons to experimental measurements at multiple levels, over a range of physically relevant conditions. Toward this end, a series of carefully designed validation experiments has been performed on the DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] to obtain comprehensive multifield, multipoint, multiwavenumber fluctuation measurements and their scalings with key dimensionless parameters. The results of two representative validation studies are presented: an elongation scaling study performed in beam heated L-mode discharges and an electron heating power scan performed in quiescent H-mode (QH-mode) discharges. A 50% increase in the elongation {kappa} is observed to lead to a {approx}50% increase in energy confinement time {tau}{sub e} and accompanying decrease in fluctuation levels, qualitatively consistent with a priori theoretical predictions and nonlinear GYRO [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] simulations. However, these simulations exhibit clear quantitative differences from experiment in the predicted magnitudes and trends with radius of turbulent fluxes and fluctuation levels which cannot be fully accounted for by uncertainties due to transport stiffness. In the QH-mode study, local nonlinear GYRO simulations that neglect fast ion effects show a similar proportional response to the applied electron cyclotron heating as the experiment, but overpredict the magnitudes of transport and fluctuation levels by a factor of 10 or more. Possible sources of this overprediction, namely nonlocal effects and self-consistent fast beam ions, are identified and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electron cyclotron current drive in low collisionality limit: On parallel momentum conservation

A comprehensive treatment of the models used in ray- and beam-tracing codes to calculate the electron cyclotron current drive (ECCD) by means of the adjoint technique, based on the adjoint properties of the collision and Vlasov operators appearing in the drift-kinetic equation, is presented. Particular attention is focused on carefully solving the adjoint drift-kinetic equation (generalized Spitzer problem) with parallel momentum conservation in the like-particle collisions. The formulation of the problem is valid for an arbitrary magnetic configuration. Only the limit of low collisionality is considered here, which is of relevance for high-temperature plasmas. It is shown that the accurate solution of the adjoint drift-kinetic equation with parallel momentum conservation significantly differs (apart from the suprathermal electron portion) from that calculated in the high-speed-limit, which is most commonly used in the literature. For high-temperature plasmas with significant relativistic effects, the accuracy of the resulting numerical models is demonstrated by ray-tracing calculations and benchmark results are presented. It is found that the ECCD efficiency calculated for ITER with parallel momentum conservation significantly exceeds the predictions obtained with the high-speed-limit model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Poloidally and radially resolved parallel D{sup +} velocity measurements in the DIII-D boundary and comparison to neoclassical computations

First measurements of the D{sup +} parallel velocity, V{sub ||}{sup D+}, in L-mode discharges in the DIII-D [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] tokamak boundary region at two poloidal locations, {theta}{approx}0 deg. and {theta}{approx}255 deg., made using Mach probes, feature a peak with velocities of up to 80 km/s at the midplane last closed flux surface (LCFS), as high as ten times the charge exchange recombination C{sup 6+} toroidal velocity, V{sub {phi}}{sup C6+}, in the same location. The V{sub ||}{sup D+} profiles are very asymmetric poloidally, by a factor of 8-10, and feature a local peak at the midplane. This peak, 1-2 cm wide, is located at or just inside the LCFS, and it suggests a large source of momentum in that location. This momentum source is quantified at {approx}0.31 N m by using a simple momentum transport model. This is the most accurate measurement of the effects of so called 'intrinsic' edge momentum source to date. The V{sub ||}{sup D+} measurements are quantitatively consistent with a purely neoclassical computational modeling of V{sub ||}{sup D+} by the code NEO[E. A. Belli and J. Candy, Plasma Phys. Controlled Fusion 50, 095010 (2008)], using V{sub {phi}}{sup C6+} as input, for {rho}{approx}0.7-0.95 at the two poloidal locations, where V{sub ||}{sup D+} measurements exist. The midplane NEO-calculated V{sub ||}{sup D+} grows larger than V{sub ||}{sup C6+} in the steeper edge gradient region and trends to agreement with the probe-measured V{sub ||}{sup D+} data near {rho}{approx}1, where the local V{sub ||}{sup D+} velocity peak exists. The measurements and computations were made in OH and L-mode discharges on an upper single null, with ion {nabla}B{sub T} drift away from the divertor. The rotating layer finding is similar in auxiliary heated discharges with and without external momentum input, except that at higher density the edge velocity weakens.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Integrated modelling of steady-state scenarios and heating and current drive mixes for ITER

Recent progress on ITER steady-state (SS) scenario modelling by the ITPA-IOS group is reviewed. Code-to-code benchmarks as the IOS group's common activities for the two SS scenarios (weak shear scenario and internal transport barrier scenario) are discussed in terms of transport, kinetic profiles, and heating and current drive (CD) sources using various transport codes. Weak magnetic shear scenarios integrate the plasma core and edge by combining a theory-based transport model (GLF23) with scaled experimental boundary profiles. The edge profiles (at normalized radius rho = 0.8-1.0) are adopted from an edge-localized mode-averaged analysis of a DIII-D ITER demonstration discharge. A fully noninductive SS scenario is achieved with fusion gain Q = 4.3, noninductive fraction f(NI) = 100%, bootstrap current fraction f(BS) = 63% and normalized beta beta(N) = 2.7 at plasma current I(p) = 8MA and toroidal field B(T) = 5.3 T using ITER day-1 heating and CD capability. Substantial uncertainties come from outside the radius of setting the boundary conditions (rho = 0.8). The present simulation assumed that beta(N)(rho) at the top of the pedestal (rho = 0.91) is about 25% above the peeling-ballooning threshold. ITER will have a challenge to achieve the boundary, considering different operating conditions (T(e)/T(i) approximate to 1 and density peaking). Overall, the experimentally scaled edge is an optimistic side of the prediction. A number of SS scenarios with different heating and CD mixes in a wide range of conditions were explored by exploiting the weak-shear steady-state solution procedure with the GLF23 transport model and the scaled experimental edge. The results are also presented in the operation space for DT neutron power versus stationary burn pulse duration with assumed poloidal flux availability at the beginning of stationary burn, indicating that the long pulse operation goal (3000s) at I(p) = 9 MA is possible. Source calculations in these simulations have been revised for electron cyclotron current drive including parallel momentum conservation effects and for neutral beam current drive with finite orbit and magnetic pitch effects.

Murakami, Masanori↗

Solenoid-free startup experiments in DIII-D

A series of DIII-D experiments was performed to investigate the potential for initiating plasma current using only poloidal field coils located outside the DIII-D central solenoid, i.e. 'solenoid-free'. Plasma current to 166 kA was achieved using 2-3MW of electron cyclotron (EC) heating and was limited by coil and power supply constraints. Flux conversion to plasma current was similar to standard DIII-D startup with some degradation at higher plasma current associated with stray fields and vertical stability issues. In preliminary solenoid-free experiments, neutral beam (NB) current drive (CD) levels were small and attributed to reduced CD efficiency associated with low electron temperature produced by the low current, low confinement plasma. Lack of plasma radial position control also contributed to a reduction of NBCD. Similarly, ECCD was small owing to low plasma temperature and outside EC launch which is required in the solenoid-free scenario. Synergistic experiments were carried out using standard solenoid initiated plasmas in order to study noninductive CD in limited, Lmode plasmas, typical of that generated by solenoid-free startup. While substantial noninductive current can be driven, self-sustaining levels of noninductive current have not yet been achieved with our present six-source co-injection NB system combined with EC and fast wave systems. At low plasma current and high levels of localized EC heating, substantial MHD is generated and this was seen to severely limit plasma performance. Although further optimization is possible in the limited plasma regime, full noninductive, steady-state operation may require diverted plasma with H-mode quality confinement. Discharges obtained during the solenoid-free campaign are compared with results of previous DIII-D campaigns aimed at achieving a steady state, noninductive CD solution.

FACILITY↗

Experiment and Modeling of ITER Demonstration Discharges in the DIII-D Tokamak

DIII-D is providing experimental evaluation of 4 leading ITER operational scenarios: the baseline scenario in ELMing H-mode, the advanced inductive scenario, the hybrid scenario, and the steady state scenario. The anticipated ITER shape, aspect ratio and value of I/{alpha}B were reproduced, with the size reduced by a factor of 3.7, while matching key performance targets for {beta}{sub N} and H{sub 98}. Since 2008, substantial experimental progress was made to improve the match to other expected ITER parameters for the baseline scenario. A lower density baseline discharge was developed with improved stationarity and density control to match the expected ITER edge pedestal collisionality ({nu}*{sub e} {approx} 0.1). Target values for {beta}{sub N} and H{sub 98} were maintained at lower collisionality (lower density) operation without loss in fusion performance but with significant change in ELM characteristics. The effects of lower plasma rotation were investigated by adding counter-neutral beam power, resulting in only a modest reduction in confinement. Robust preemptive stabilization of 2/1 NTMs was demonstrated for the first time using ECCD under ITER-like conditions. Data from these experiments were used extensively to test and develop theory and modeling for realistic ITER projection and for further development of its optimum scenarios in DIII-D. Theory-based modeling of core transport (TGLF) with an edge pedestal boundary condition provided by the EPED1 model reproduces T{sub e} and T{sub i} profiles reasonably well for the 4 ITER scenarios developed in DIII-D. Modeling of the baseline scenario for low and high rotation discharges indicates that a modest performance increase of {approx} 15% is needed to compensate for the expected lower rotation of ITER. Modeling of the steady-state scenario reproduces a strong dependence of confinement, stability, and noninductive fraction (f{sub NI}) on q{sub 95}, as found in the experimental I{sub p} scan, indicating that optimization of the q profile is critical to simultaneously achieving the f{sub NI} = 1 and Q = 5 goals. Extended integrated modeling is being developed to improve capability for ITER projection by including the experimental observations of density peaking, ELM characteristics, NTM suppression and coupled core-edge-SOL transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simultaneous measurement of core electron temperature and density fluctuations during electron cyclotron heating on DIII-D

New measurements show that long-wavelength (k{sub t}hetarho{sub s}<0.5) electron temperature fluctuations can play an important role in determining electron thermal transport in low-confinement mode (L-mode) tokamak plasmas. In neutral beam-heated L-mode tokamak plasmas, electron thermal transport and the amplitude of long-wavelength electron temperature fluctuations both increase in cases where local electron cyclotron heating (ECH) is used to modify the plasma profiles. In contrast, the amplitude of simultaneously measured long-wavelength density fluctuations does not significantly increase. Linear stability analysis indicates that the ratio of the trapped electron mode (TEM) to ion temperature gradient (ITG) mode growth rates increases in the cases with ECH. The increased importance of the TEM drive relative to the ITG mode drive in the cases with ECH may be associated with the increases in electron thermal transport and electron temperature fluctuations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Applications of Electron Cyclotron Waves in the DIII-D Tokamak

Electron cyclotron heating (ECH) and electron cyclotron current drive (ECCD) have progressed from being the subject of experiments to being a prime tool for carrying out experiments on other topics. ECH has different characteristics than neutral beam heating: ECH heats only the electrons, heats very locally and controllably, does not inject momentum or particles, and may be arranged to drive highly localized currents or to just heat. These differences make ECH useful in a very wide range of experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advanced techniques for neoclassical tearing mode control in DIII-D

Two techniques were developed at DIII-D [J. L. Luxon, Nucl. Fusion 42, 64 (2002)] to tackle ITER-specific aspects of neoclassical tearing mode (NTM) control, namely, (1) the relatively small size of the rotating islands, smaller than the electron cyclotron current drive (ECCD) deposition region, and (2) the increased tendency of the islands, compared to present devices, to lock to the wall or to the residual error field, in a position not necessarily accessible to ECCD. Modulated ECCD is known to suppress small islands more efficiently, when ''broad,'' than continuous ECCD. At DIII-D, a NTM of poloidal/toroidal mode numbers m/n=3/2 was completely stabilized by a new technique where oblique electron cyclotron emission acted at the same time as an indicator of good alignment between ECCD and the island, and as a waveform generator, for modulation in synch and in phase with the island O-point. In another experiment, after locking in an unfavorable position, a 2/1 island was steered by externally generated magnetic perturbations, brought in the view of the gyrotrons and partly stabilized by ECCD in the island O-point. Magnetic perturbations were also used to sustain and control the mode rotation, which has the potential for an easier ECCD modulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Validation of on- and off-axis neutral beam current drive against experiment in DIII-D

Neutral beam current drive (NBCD) experiments in DIII-D using vertically shifted plasmas to move the current drive away from the axis have clearly demonstrated robust off-axis NBCD. Time-dependent measurements of magnetic field pitch angles by the motional Stark effect diagnostic are used to obtain the evolution of the poloidal magnetic flux, which indicates a broad off-axis NBCD profile with a peak at about half the plasma minor radius. In most cases, the measured off-axis NBCD profile is consistent with calculations using an orbit-following Monte Carlo code for the beam ion slowing down including finite-orbit effects provided there is no large-scale magnetohydrodynamic activity such as Alfven eigenmodes modes or sawteeth. An alternative analysis method shows good agreement between the measured pitch angles and those from simulations using transport-equilibrium codes. Two-dimensional image of Doppler-shifted fast ion D{sub {alpha}} light emitted by neutralized energetic ions shows clear evidence for a hollow profile of beam ion density, consistent with classical beam ion slowing down. The magnitude of off-axis NBCD is sensitive to the alignment of the beam injection relative to the helical pitch of the magnetic field lines. If the signs of toroidal magnetic field and plasma current yield the proper helicity, both measurement and calculation indicate that the efficiency is as good as on-axis NBCD because the increased fraction of trapped electrons reduces the electron shielding of the injected ion current, in contrast with electron current drive schemes where the trapping of electrons degrades the efficiency. The measured off-axis NBCD increases approximately linearly with the injection power, although a modest amount of fast ion diffusion is needed to explain an observed difference in the NBCD profile between the measurement and the calculation at high injection power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma Shape Optimization for Steady-State Tokamak Development in DIII-D

For a more detailed account of the results summarized here and for references, see C.T. Holcomb et al., Phys. Plasmas 16, 056116 (2009). Advanced tokamak research on DIII-D is focused on developing a high fusion gain, steady-state scenario that would eliminate or greatly reduce the demands on an inductive transformer in future machines. Steady-state operation requires the inductively driven current density (j{sub Ind}) be zero everywhere. Most of the total current I{sub p} is typically from self-driven bootstrap current, with the remainder driven by external noninductive sources, such as neutral beam and radiofrequency current drive. This paper describes an extension of the fully noninductive condition (f{sub NI} {approx} 100%) to {approx}0.7 current relaxation times that was achieved by a combination of more available ECCD and new scientific insights. The insights are an optimization of performance through variation of the plasma shape parameter known as squareness ({zeta}) and an optimization of divertor magnetic balance. These optimizations simultaneously improve stability, confinement, and density control. These are each essential for achieving fully noninductive operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗