Engineering topics
Publications and source records attributed to Presley, L. L..
Report describes $700 million wind-tunnel complex at Ames Research Center, including auxiliary support systems, test instrumentation, and special test rigs. Planned near-term facility improvement aimed at providing new test capabilities and increased productivity, as well as some potential longer-term improvements, also discussed. Aerodynamic test facilities range from subsonic wind tunnels to highenthalpy arc jets.
This paper presents results of a study of the test section configuration required to minimize or alleviate interference effects on model flow produced by the presence of test section walls in the aerodynamic testing of two dimensional transonic airfoils in a shock tube. Tests at a nominal Mach number of 0.85 and a chord Reynolds number of 2,000,000 were carried out by means of schlieren photography and pressure measurements for several symmetric airfoil profiles using shock tube test sections with unmodified straight walls, contoured walls, and slotted walls with adjacent chambers. Results were compared with corresponding results from conventional wind tunnel tests of the airfoils. Results for the straight wall tests show major airfoil flow distortions. Results from contoured wall tests and those performed using a slotted wall test section developed in this study exhibit essential agreement with wind tunnel results. The collective results show that test sections for aerodynamic testing can be designed for shock tubes that will alleviate wall interference effects.
The effects of angle of attack on supersonic mixed compression inlet performance at four different locations about a hypothetical forebody are given. A computational method to predict optimum inlet location, orientation, and centerbody control schedule for design and off-design performance is described. The effects of inlet location and a forward canard on the angle-of-attack performance of a normal shock inlet at transonic speeds were studied. Proper integration of inlet location and a forward canard can enhance the angle-of-attack performance of a normal shock inlet. Two lower lip treatments for improving the angle-of-attack performance of rectangular inlets at transonic speeds are discussed.
Performance analysis of a gas-driven shock tube shows that transonic airfoil flows with chord Reynolds numbers of the order of 100 million can be produced, with limitations being imposed by the structural integrity of the facility or the model. A study of flow development over a simple circular arc airfoil at zero angle of attack was carried out in a shock tube at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photography and airfoil pressure measurements show that steady transonic flows similar to those produced for the same airfoil in a wind tunnel can be generated within the available testing time in a shock tube with properly contoured test section walls.
A performance analysis of gas-driven shock tubes shows that transonic airfoil flows with chord Reynolds numbers in the range of 100 million can be generated behind the primary shock in a large shock tube. A study of flow over simple airfoils has been carried out at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photos and airfoil pressure measurements show that steady transonic flows similar to those observed for the airfoils in wind tunnels can be generated within the available testing time in a shock tube with either properly-contoured test section walls or a properly-designed slotted-wall test section. The study indicates that the shock tube is a useful facility for studying two-dimensional high Reynolds number transonic airfoil flows.
A method is developed for solving the laminar and turbulent compressible boundary layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent layer, shock wave interactions. Several Navier-Stokes solutions are obtained for each of the laminar boundary layer, shock wave interactions considered. Comparison of these solutions indicates a first order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow. Comparison of the present boundary layer solutions with the Navier-Stokes solutions and with data for a given Mach number indicates that as long as the separation bubble is small, the boundary layer approximation yields solutions whose accuracy is comparable to the Navier-Stokes solutions.
Several solutions for the internal flow in axisymmetric supersonic inlets at angle of attack were obtained. A shock-capturing finite-difference technique was used to obtain the solutions. Good overall agreement between the shock-capturing solutions and experimental data was obtained, except in regions of strong viscous effects or boundary-layer removal. The required centerbody translation with changes in freestream Mach number and angle of attack was obtained and agrees qualitatively with experimental data.
A method is developed for solving the laminar and turbulent compressible boundary-layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent boundary-layer, shock-wave interactions. Several Navier-Stokes solutions were obtained for each of the laminar boundary-layer, shock-wave interactions considered. Comparison of these solutions indicates a first-order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow.
Shock-capturing solutions for an axisymmetric supersonic inlet at small angles of attack are obtained. Good overall agreement between the shock-capturing solutions and experimental data is shown except in regions of strong viscous effects or boundary-layer removal. Although the results indicate a strong potential for the use of shock-capturing or finite-difference solutions for internal flows, improvement in the ability to handle the reflection of strong shockwaves having downstream Mach numbers near 1 is needed.
The shock tube as a device to fulfill current needs for testing of transonic airfoils at high Reynolds numbers is considered. Performance analysis of a gas-driven shock tube shows that transonic airfoil flows with chord Reynolds numbers in the range of 100 million can be produced. A study of flow development over a simple airfoil has been carried out in a shock tube at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photography and airfoil pressure measurements show that steady transonic flows similar to those produced for the same airfoil in a wind tunnel can be generated within the available testing time in a shock tube with properly contoured test section walls. The study indicates that the shock tube is a viable alternative as a facility for studying high Reynolds number transonic airfoil flows.
Application of two laser wavelengths passing through plasma measures electron density and temperature. Function depends on determining absorption of light at two wavelengths. Nature of reaction is explained and schematic diagram of equipment is included.
The method of characteristics for a chemically reacting gas is used in the construction of the time-dependent, one-dimensional flow field resulting from the normal reflection of an incident shock wave at the end wall of a shock tube. Nonequilibrium chemical reactions are allowed behind both the incident and reflected shock waves. All the solutions are evaluated for oxygen, but the results are generally representative of any inviscid, nonconducting, and nonradiating diatomic gas. The solutions clearly show that: (1) both the incident- and reflected-shock chemical relaxation times are important in governing the time to attain steady state thermodynamic properties; and (2) adjacent to the end wall, an excess-entropy layer develops wherein the steady state values of all the thermodynamic variables except pressure differ significantly from their corresponding Rankine-Hugoniot equilibrium values.
The absorption coefficients of 1.15- and 3.39-micrometer radiation for a homogeneous H-He plasma have been measured in a temperature and electron density range where the major absorption mechanisms are electron-ion inverse bremsstrahlung and neutral-atom photoionization. Measurements were made behind both the incident and reflected shock waves in a driven tube by recording the laser intensity transmitted along the tube diameter as a function of time. The measured values compare well with those obtained from theoretical calculations for a gas in thermodynamic equilibrium.
Free electron formation ahead of strong shock waves traveling into nitrogen-oxygen mixtures in shock tube, observing electron densities
Electron density profiles in plasma ahead of shock waves determined with electrostatic probes in shock tubes
Flow fields construction for normal shock waves with nonequilibrium chemical reactions reflected from shock tube end wall
Precursor electron densities measured in nitrogen and air ahead of shock waves, noting shock tube wall reflectivity
Flow fields construction for normal shock waves with nonequilibrium chemical reactions reflected from shock tube end wall