Search NASA⌕ Search

Engineering topics

Prestemon, S O

Publications and source records attributed to Prestemon, S O.

Introduction of Nonlinear Properties Into Hierachical Models of Nb3Sn Strands

The development of computational models representing Rutherford cable formation and deformation is necessary to investigate the strain state in the superconducting filaments in Nb{sub 3}Sn magnets. The wide variety of length scales within accelerator magnets suggests usage of a hierarchical structure within the model. As part of an ongoing investigation at LBNL, a three-dimensional simplified nonlinear multiscale model is developed as a way to extend previous linear elastic versions. The inclusion of plasticity models into the problem formulation allows an improved representation of strand behavior compared to the linear elastic model. This formulation is applied to a single Nb{sub 3}Sn strand to find its effective properties as well as the strain state in the conductor under loading.

43 PARTICLE ACCELERATORS↗

Numerical Investigation of the Quench Behavior of Bi2Sr2CaCu2Ox Wire

The quench behavior of Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub x} (Bi2212) wire is investigated through numerical simulations. This work is part of the U.S. Very High Field Superconducting Magnet Collaboration (VHFSMC). Numerical simulations are carried out using a one-dimensional computational model of thermal transport in Bi2212 composite wires. A quench is simulated by introducing heat in a section of the wire, and the voltage and temperature are monitored as function of time and position. The quench energy, normal zone propagation velocity, and spatial distribution of temperature are calculated for varying transport current and applied magnetic field. The relevance of these simulations in defining criteria for experimental measurements is discussed.

43 PARTICLE ACCELERATORS↗

A Superconducting transformer system for high current cable testing

This article describes the development of a direct-current (dc) superconducting transformer system for the high current test of superconducting cables. The transformer consists of a core-free 10 464 turn primary solenoid which is enclosed by a 6.5 turn secondary. The transformer is designed to deliver a 50 kA dc secondary current at a dc primary current of about 50 A. The secondary current is measured inductively using two toroidal-wound Rogowski coils. The Rogowski coil signal is digitally integrated, resulting in a voltage signal that is proportional to the secondary current. This voltage signal is used to control the secondary current using a feedback loop which automatically compensates for resistive losses in the splices to the superconducting cable samples that are connected to the secondary. The system has been commissioned up to 28 kA secondary current. The reproducibility in the secondary current measurement is better than 0.05% for the relevant current range up to 25 kA. The drift in the secondary current, which results from drift in the digital integrator, is estimated to be below 0.5 A/min. The system's performance is further demonstrated through a voltage-current measurement on a superconducting cable sample at 11 T background magnetic field. The superconducting transformer system enables fast, high resolution, economic, and safe tests of the critical current of superconducting cable samples.

43 PARTICLE ACCELERATORS↗

Mechanical design and analysis of an eight-pole superconducting vector magnet for soft x-ray magnetic dichroism measurements

An eight-pole superconducting magnet is being developed for soft x-ray magnetic dichroism (XMD) experiments at the Advanced Light Source, Lawrence Berkley National Laboratory (LBNL). Eight conical Nb{sub 3}Sn coils with Holmium poles are arranged in octahedral symmetry to form four dipole pairs that provide magnetic fields of up to 5 T in any direction relative to the incoming x-ray beam. The dimensions of the magnet yoke as well as pole taper, diameter, and length were optimized for maximum peak field in the magnet center using the software package TOSCA. The structural analysis of the magnet is performed using ANSYS with the coil properties derived using a numerical homogenization scheme. It is found that the use of orthotropic material properties for the coil has an important influence in the design of the magnet.

42 ENGINEERING↗