Search NASA⌕ Search

Engineering topics

Pries, Jason

Publications and source records attributed to Pries, Jason.

At least 37 records · Page 2

Electrification Annual Progress Report (FY2019)

During fiscal year 2019 (FY 2019), the U.S. Department of Energy (DOE) Vehicle Technologies Office (VTO) funded early stage research & development (R&D) projects that address Batteries and Electrification of the U.S. transportation sector. The VTO Electrification Sub-Program is composed of Electric Drive Technologies, and Grid Integration activities. The Electric Drive Technologies group conducts R&D projects that advance electric motors and power electronics technologies. The Grid and Charging Infrastructure group conducts R&D projects that advance grid modernization and electric vehicle charging technologies. This document presents a brief overview of the Electrification Sub-Program and progress reports for its R&D projects. Each of the progress reports provide a project overview and highlights of the technical results that were accomplished in FY 2019.

25 ENERGY STORAGE↗

20-kW Bi-directional Wireless Power Transfer System with Energy Storage System Connectivity

The severity of the economic impact caused by grid outages has been the driving factor for creating innovative solutions that increases interest for the deployment of distributed energy resources to reduce the impact of grid outages. This study presents a novel way of providing export power using bi-directional wireless power transfer (WPT) systems for ac grid side power and mobile energy storage systems (ESSs) connectivity. The proposed concept here interfaces the EV batteries to the AC grid and also can redirect the power from the stationary ESS to grid, to EV batteries, or both simultaneously; providing the capabilities of an uninterrupted power supply (UPS). Results demonstrate the performance and the functionality of the system with overall efficiencies 93% to 97%, depending on the operating mode.

Onar, Omer↗

Direct Envelope Modeling of Load-Resonant Inverter for Wireless Power Transfer Applications

This paper presents the application of direct envelope modeling technique to primary side LCC tuned resonant wireless power transfer system. The method adapted here decomposes the HF resonant inverter output to a fundamental component and two dominant sidebands. The small-signal dutycycle-to-primary-coil-current-envelope transfer function of a primary side LCC tuned WPT system is then derived as the summation of the responses to the fundamental and the sideband components. The theoretical and simulation results are in good agreement indicating the validity of the approach to be applied to WPT systems.

Galigekere, Veda Prakash↗

Computationally Efficient AC Resistance Model for Stator Winding With Rectangular Conductors

The resistance of the electric machine’s windings is an important parameter when analyzing the machine’s performance, as conduction losses in the winding are often the largest loss component. However, this resistance changes with frequency due to the skin and proximity effects, making it challenging to accurately estimate these losses. In this article, a computationally efficient, general method of calculating the ac resistance of an electric machine winding with rectangular conductors is presented. The method uses a 1-D magnetoquasi-static model of the stator slot region to develop boundary transfer relations between individual turns. These relations are then used to create an impedance matrix from which the ac resistance can be calculated. This technique is more flexible than previous solutions since it can accommodate different winding configurations such as fractional-pitch windings. It is shown that a fractional-pitch winding has a lower ac resistance than a full-pitch winding. Finally, finite-element analysis simulations and experimental results are used to validate the proposed method.

42 ENGINEERING↗

A 50-kW Three-Phase Wireless Power Transfer System Using Bipolar Windings and Series Resonant Networks for Rotating Magnetic Fields

The mass and volume of wireless power transfer (WPT) systems for charging electric vehicles are directly related to the rated power of the system. The difficulties of high-power wireless charging are exacerbated by the need to meet the same practical constraints associated with vehicle integration as lower power systems. Therefore, more advanced techniques are necessary to improve power density and specific power of wireless charging systems for high-power applications. This article presents theory and analysis of three-phase inductive WPT systems with bipolar phase windings. Magnetic coupler topologies and the theoretical and practical aspects of series three-phase resonant compensation networks are discussed. The systems under consideration are designed to utilize rotating magnetic fields to achieve a power transfer characteristic that is temporally smoother than single-phase systems. Other benefits associated with rotating magnetic field based WPT, including reduced ferrite mass, filter component requirements, and electromagnetic field emissions, are discussed. Experimental results of a prototype system are presented in both aligned and misaligned configurations. The system is demonstrated transferring 50 kW with 95% dc-to-dc efficiency over a 150-mm airgap in the aligned case. On a per-pad basis, the magnetic couplers achieve a power density of 195 kW/m 2 and a specific power of 3.65 kW/kg. Finally this article is accompanied by a video of the rotating magnetic field produced by a simulated three-phase WPT system.

42 ENGINEERING↗

Variable Duty Control of Three-Phase Voltage Source Inverter for Wireless Power Transfer Systems

This paper presents duty control and analysis of the three-phase voltage source inverter (VSI) to adjust the output power for three-phase wireless power transfer (WPT) applications. Analytical results show significant reductions in the inverter dc link ripple current with the three-phase system over single-phase WPT counterparts. Simulation and experimental results for an 18 kW three-phase series-series WPT system are included to validate the duty control and analysis. Experimental results also demonstrated the output voltage can be controlled over a wide range by adjusting the inverter duty.

Su, Gui-Jia↗

Comparison of Leakage Magnetic Field from Matched and Mismatched Double-D Coil based Wireless Charging System for Electric Vehicles

In this paper, a magnetic shield design is proposed for a matched and mismatched coil based high-power wireless charging system (WCS). The high-power WCS are highly prone to exceed the safety limits of both the electric and magnetic field leakage. The leakage magnetic field from the mismatched pads are higher than the matched pads. In a mismatched system, the receiver is usually made much smaller than the transmitter, which requires higher amp-turns in the coils to transfer the same amount of power. In addition, coupling factor is lower in mismatched systems. Therefore, the electromagnetic field (EMF) emission is higher for a mismatched system, compared to matched system where both the transmitter and receiver are similar and large. This phenomenon applies for both the nonpolarized-circular and DD pads. In this paper, the leakage magnetic field is compared for the matched-DD and mismatched-DD coil-based WCS. The leakage field is evaluated through finite element analysis (FEA) and verified experimentally through an 11 kW mismatched DD system. The results show that, the leakage magnetic field is much higher for a mismatched WCS, compared to a matched WCS.

Mostak, Mostak Mohammad↗

Influence of scan pattern and geometry on the microstructure and soft-magnetic performance of additively manufactured Fe-Si

The influence of geometry and scan pattern on the microstructure evolution and magnetic performance of additively manufactured Fe-3Si components was investigated. To reduce eddy current losses, novel geometries were designed and built and the microstructure and properties of these samples were characterized. The laser scan pattern was shown to strongly influence both the as-built grain structure and strength of the crystallographic texture, resulting in measurable changes in the as-built magnetic performance. In thin wall samples, heat treatment resulted in an increase in the maximum relative magnetic permeability and decrease in power losses in most samples, consistent with grain growth. However, decreases in the spacing between thin walls to increase the stacking factor of the cross-section was shown to result in unwanted electrical shorting between walls and an increase in eddy current losses. Compared to simple parallel plate construction and a mesh structure, a novel cross-section design based on the Hilbert space filling curve was found to produce the lowest power losses. The mechanisms behind these results were explored using a combination of heat conduction and electromagnetic simulations, providing a route for future component and process optimization.

36 MATERIALS SCIENCE↗

System Design of Dynamic Wireless Power Transfer for Automated Highways

Dynamic wireless power transfer (DWPT) has been proposed as a solution to power electric vehicles (EVs)on future electrified highways. However, there has been little consideration of how the coordination of electric connected and automated vehicles (CAVs) could impact DWPT system designs in future scenarios. In this paper, a DWPT system design is optimized for a future highway where CAVs travel in coordinated groups, with each CAV in the group powered by the same DWPT section. As the distribution of smaller light-duty vehicles (LDVs) and larger heavy-duty vehicles (HDVs) in each group is varied, the DWPT system power level, transmitter length, and the equivalent receiver loads are adjusted to minimize the infrastructure requirements and energy losses of the DWPT system. The outputs from this analysis are used to determine the optimal groupings of vehicles for a given DWPT system. The analysis suggests that CAV coordination could aid the deployment of DWPT systems and reduce the overall infrastructure and energy losses of DWPT systems.

Foote, Andrew↗

Investigation of Powder Processing, Heat Treating, and Texturing to Improve Gas Atomized alnico Magnets for use in Electric Drive Motors

Alnico permanent magnet materials have been proposed as a rare earth free permanent magnet alternative during an ongoing search to replace rare earth permanent magnets that are used for interior permanent magnet motors, a common motor found in electric vehicles. A powder processing approach was used to study two alnico alloys (Full-Co and lower cost Co-Lean, both with enhanced coercivity) to anticipate high volume manufacturing needed to supply millions of permanent magnets to interior permanent magnet motors. In this study the two alloys were gas atomized, compression molded, and solid-state sintered to fabricate near-final shape alnico magnets. The Full-Co displayed abnormal grain growth (resulting in >1 mm size grains) during sintering while the Co-Lean did not (~20 μm – 400 μm sized grains depending on the sintering hold times). Solid state grain alignment was used to promote a <001> textured (easy axis) microstructure to enhance magnetic properties, yet both alloys did not show predicted grain alignment behavior. Comparisons of the powder processing, microstructures, and magnetic properties of the two alloys will be discussed, as well as an evaluation as to why non-theoretical processing behavior of the Full-Co and Co-Lean alnico permanent magnets is occurring. Preliminary interior permanent magnet motor designs for alnico magnets are discussed, as this is the overarching objective for powder-based alnico permanent magnets.

Rinko, Emily↗

Sensitivity Analysis of an LCC-LCC Compensated 20-kW Bidirectional Wireless Charging System for Medium-Duty Vehicles

In this paper, sensitivity analysis of an LCC-LCC compensated bidirectional wireless charging system is presented. In a wireless charging system for electric vehicle applications, the effective load impedance varies significantly with the state-of-charge (SOC)of the battery. Due to the change in system parameters, resonant frequency, and transferred power, the efficiency of the system varies significantly. Sensitivity analysis of the system characteristics reveals the optimal operating region and required control strategy to operate within that region. Sensitivity analysis is even more important for a bidirectional system with mismatched input and output voltage levels. In this paper, the sensitivity of a bidirectional 20 kW wireless charging system is investigated analytically and the results are validated experimentally. The experimental results for a geometrically matched Double-D (DD) coil-based LCC-LCC tuned bidirectional WCS with asymmetric voltage levels show that the voltage gains and input impedance of the system are highly sensitive near the resonant frequency.

Mostak, Mostak Mohammad↗

Continuum Modeling of Inductor Magnetic Hysteresis and Eddy Currents in Resonant Circuits

This paper presents a high-fidelity finite-element modeling technique for magnetic hysteresis and eddy current losses in toroid inductors. The method is based on the separation of ferromagnetic loss characteristics into two components: a quasi-static hysteresis component and a dynamic eddy current component. The Preisach model is used to describe the quasi-static magnetic hysteresis behavior of the core, providing strong guarantees on the reproducibility of the experimentally measured characteristics. This model is used to represent the magnetic field constitutive relationships within a finite-element framework combining the effects of hysteresis and eddy currents in a unified dynamic simulation. The finite-element model of the toroid is used as a high-order inductor model coupled to a resonant circuit simulation. The modeling technique is validated through experimental measurements on two different series RLC circuits. The first circuit is based on an M19 electrical steel toroid having resonant frequency near 200 Hz. The second circuit is based on a T38 ferrite toroid having a resonant frequency near 10 kHz. The models agree closely with the measured voltages, currents, and losses. The models also successfully predict discontinuities in the measured frequency responses due to the existence of bistable operating regimes.

42 ENGINEERING↗

Design of an EMF Suppressing Magnetic Shield for a 100-kW DD-Coil Wireless Charging System for Electric Vehicles

This study investigates the electromagnetic field (EMF) emissions of a 100-kW Double-D (DD) wireless charging system (WCS). A shielding technique is proposed to suppress the magnetic field emissions below the limits set by the International Commission on Non-Ionizing Radiation Protection (ICNIRP). The leakage pattern produced by the DD coil is different than unipolar (circular, rectangular, etc.) pads and traditional eddy current based aluminum shields are not effective at suppressing this leakage field. Therefore, a methodically designed magnetic shield could be more effective. This study proposes a shielding technique for DD coils using a combination of aluminum shielding and a low reluctance magnetic shield to suppress the magnetic field emissions. The shielding effectiveness is evaluated through finite element analysis (FEA) models and tested experimentally. The effectiveness of the proposed magnetic shielding and the limits of the conventional aluminum shielding are studied. A prototype 11-kW DD coil wireless charging system is used to experimentally validate the proposed shielding technique. The experimental results show that the aluminum shield increases the emissions of DD coils by 25% and the proposed magnetic shield can be employed to suppress the emission by 60%.

Mohammad, Mostak↗

Modeling, Design, and Experimental Verification of a WPT Level-3 Wireless Charger with Compact Secondary Coupler

This study introduces a wireless power transfer (WPT) Level-3 rated charger with >11 kW nominal output. The proposed system is interoperable for WPT Level-1, 2, and 3 charger applications of which power levels and airgap separations are defined in SAE J2954. The system designed for this study is capable of operating at Z 1 (100-150 mm), Z 2 (140-210 mm) and Z 3 (170-250 mm) vehicle assembly ground clearance range classes with a very compact vehicle-side (secondary) coupler. The couplers are characterized for the maximum output power (P out ) and the coupling coefficient (k) with different airgaps. System frequency response and the sensitivity analysis are presented. Experimental results are shown for 190.5 mm and 216 mm airgap separations. These results demonstrate that the proposed system with a very compact secondary can be operated at these ground clearance classes with high efficiency at WPT level-3 charging levels.

Onar, Omer↗

Secondary Active Rectifier Control Scheme for a Wireless Power Transfer System with Double-Sided LCC Compensation Topology

This paper proposes a secondary control method using an active rectifier for a double-sided LCC tuned wireless power transfer system (WPT) to reduce the communication requirements of the system. As the active rectifier regulates the output power with a constant primary coil current, the secondary circulating time interval is adjusted while maintaining a unity power factor. First, circuit modelling and sensitivity analyses for the voltage gain, input impedance, coil current rating and power transfer are investigated with a design example of 20kW WPT. Subsequently, the control scheme is developed by considering the four operation modes with the phase difference as the control variable. To prove the effectiveness of the proposed control method, a simulation model is built, and the results demonstrate good dynamic performance with high accuracy for voltage regulation. Compared with the conventional secondary control, it improves the performance of the system along with a well-developed converter gain by maintaining the equivalent load resistive and reduced circulating time intervals, which further improves the system efficiency. The proposed system also eliminates the need for an additional de/de converter on the secondary side.

Zou, Shenli↗

Comparison of 22 kHz and 85 kHz 50 kW Wireless Charging System Using Si and SiC Switches for Electric Vehicle

Fast charging in transportation application requires high-power (>50 kW) operation. The overall size of wireless charging systems (WCS) must increase to meet the high-power requirement. As a result, high power systems produce more electromagnetic field (EMF) emissions. Although higher operating frequencies (85 kHz) reduce the size of inductors and capacitors, system losses tend to increase. High-power systems are traditionally investigated for 10 kHz to 22 kHz operation to reduce the switching loss in the converter, and conductive and magnetic losses in the power pad. The use of SiC MOSFETs reduces conduction and switching losses in the converter even at higher frequencies. In this paper, a comprehensive loss comparison of 50 kW wireless charging system is conducted for 85 kHz and 22 kHz operation of Si MOSFET and SiC MOSFET converters. Detailed performance indexes are compared analytically as a function of frequency and verified using FEA and PLECS. This comprehensive system level study shows that magnetic losses can be reduced significantly, and that EMF emission can be reduced by 50% by moving from 22 kHz to 85 kHz. Moreover, the system requires 50% less copper and allows a significant reduction in the size of the primary and secondary filter capacitor at 85 kHz. The results show that the system efficiency at 85 kHz can be increased by 21% compared to 22 kHz operation by using a SiC MOSFET converter.

Shahidul haque, Moinul↗

Coil Power Density Optimization and Trade-off Study for a 100kW Electric Vehicle IPT Wireless Charging System

This paper presents a trade–off study examining the impacts of modifying resonant frequency and coil current density on coil power density for a 100kW electric vehicle charging system. We find that power density can be increased significantly by moving to higher operating frequency and current density with marginal impact to overall coil–to–coil transfer efficiency. A detailed prototype model of a 150 kVA rated coil set is presented along with loss estimates from magnetic field simulations and initial test results up to 50kW.

Pries, Jason↗

Design and Implementation of an optimized 100 kW stationary wireless charging system for EV battery recharging

This paper presents the design, analyses and implementation of an optimized single stage high power wireless charging system capable of transferring 100 kW at an operating frequency of 22 kHz and a coil-to-coil distance of 5 inches.The detailed design and implementation of the power electronics including the high frequency inverter and rectifier and wireless power transfer coils along with the resonant stage are described. FEA simulation results of the coils and the resonant network analysis are validated by using a Venable frequency response analyzer. Experimental results corresponding to 50 kW operation are presented to validate the design process.

Galigekere, Veda Prakash↗