Search NASA⌕ Search

Engineering topics

Prince, Andrew

Publications and source records attributed to Prince, Andrew.

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Boiling-Water Reactor Testing Capability in the Advanced Test Reactor

I-Loop is an irradiation facility that is currently being installed at the Advanced Test Reactor. It is a two-loop test facility capable of performing Light Water Reactor (LWR) irradiations in prototypic coolant conditions. The two loops are being installed to be capable of both Boiling Water Reactor (BWR) and Pressurized Water Reactor (PWR) pressure, temperature, and chemistry environments. Each loop is nominally dedicated as a BWR or PWR for simplicity of operations. In-reactor water loop testing that an I-Loop provides is key to the deployment of new accident tolerant fuel technologies and other advanced LWR fuel concepts. Currently, pressurized water loops are the only testing facilities available to test BWR fuel concepts. Their test environments are non-prototypic at higher pressure/temperature and at single-phase fluid flow conditions. This void in the LWR test bed capabilities is one that the I-Loop is uniquely situated to provide. This report discusses the mechanical design, thermal hydraulic calculations, and neutronic calculations of a proposed standard experiment of accident tolerant BWR fuel concepts. Mechanical design examines the geometry and features of the main components. Thermal hydraulic calculations examine the modeling and results of the two-phase flow options available. Lastly, neutronic calculations examine the Monte Carlo analysis of enrichment, heat rates, and flux spectrum.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2019

A Design for a Two-Stage Solid Mars Ascent Vehicle

A solid propulsion system design is being considered for a conceptual Mars Ascent Vehicle (MAV) as part of a potential robotic Mars Sample Return campaign. A Preliminary Architecture Assessment for a MAV is being conducted at Marshall Space Flight Center. Experts from all relevant areas are involved in a rapid design and analysis cycle to define a MAV vehicle utilizing solid propulsion. The design presented here is the solid motor propulsion concept result of the study. Whereas solid motors have been used on Mars missions in the past during descent, none have been required to reside on the surface for a period of time prior to functioning. This difference will expose the MAV to relatively extreme temperatures. Other challenges exist in designing a solid propulsion system for MAV including performance interactions with other vehicle inert masses and minimizing orbit dispersions. These considerations were examined and a preliminary CAD model of the motors was created. Along with additional pertinent inputs from other disciplines, a solid propulsion vehicle concept for the MAV is described.

Prince, Andrew↗
NASA NTRS2019

Qualification of a Hybrid Propulsion System for the Mars Ascent Vehicle

Technology for a hybrid based propulsion system is being developed to support a potential Mars Sample Return campaign. A Mars Ascent Vehicle (MAV) concept for launching samples off of Mars, and delivering them to orbit for further transport to Earth may utilize hybrid propulsion due to the predicted favorable low temperature characteristics and high performance of this option. However, the hybrid option is still undergoing technology development to demonstrate these capabilities. Once development of a capable hybrid propulsion system is proven, further work will be required. This will include environmental testing relative to the mission, and integration with the vehicle reaction control systems and payload. Qualification of such a system will be a significant effort. It will require specialized procurements for the propellants and environments involved, and further testing of the more specialized designs. This paper details an estimate of the tasks required to complete development efforts from Technical Readiness Level 5 (TRL5) through qualification. A success based program was formulated to reach the required performance metrics sufficient for a standard Preliminary Design Review (PDR). Using task level inputs from team members cost and schedule were conceived for continued progress to Critical Design Review (CDR), then through Qualification.

Prince, Andrew↗
NASA NTRS2019

Development Concepts for Mars Ascent Vehicle (MAV) Solid and Hybrid Vehicle Systems

The Advanced Concepts Office (ACO) at Marshall Space Flight Center (MSFC) has conducted ongoing studies and trades into options for both hybrid and solid vehicle systems for potential Mars Ascent Vehicle (MAV) concepts for the Jet Propulsion Laboratory (JPL). Two MAV propulsion options are being studied for use in a potential Mars Sample Retrieval (MSR) campaign. The following paper describes the current concepts for hybrid and solid propulsion vehicles for MAV as part of a potential MSR campaign, and provides an overview of the ongoing studies and trades for both hybrid and solid vehicle system concepts. Concepts and options under consideration for vehicle subsystems include reaction control system (RCS), separation, and structures will be described in terms of technology readiness level (TRL), benefit to the vehicle design, and associated risk. A hybrid propulsion system, which uses a solid fuel core and liquid oxidizer, is currently being developed by JPL with support from MSFC. This type of hybrid propulsion vehicle would allow the MAV to be more flexible at the cost of higher complexity, in contrast to the solid propulsion vehicle that is simpler, but allows less flexibility. The solid propulsion vehicle study performed by MSFC in 2018 further refined the solid propulsion system sizing as well as added definition to vehicle subsystem concepts, including the RCS, structures and configuration, interstage and separation, aerodynamics, and power/avionics. The studies were performed using an iterative concept design methodology, engaging subject matter experts from across MSFC’s propulsion and vehicle systems disciplines as well as seeking trajectory feedback from analysts at JPL.

McCollum, Lisa Tunstill↗
NASA NTRS2019

Mars Ascent Vehicle (MAV) Solid Motor Technology Plans

Recent trades have taken place on solid propulsion options to support a potential Mars Sample Retrieval Campaign. Mass and dimensional requirements for a Mars Ascent Vehicle (MAV) are being assessed. One MAV vehicle concept would utilize a solid propulsion system. Key challenges to designing a solid propulsion system for MAV include low temperatures beyond common tactical and space requirements, performance, planetary protection, mass limits, and thrust vector control system. Two solutions are addressed, a modified commercial commercially available system, and an optimum new concept.

Prince, Andrew↗
NASA NTRS2019

Development Concepts for Mars Ascent Vehicle (MAV) Solid and Hybrid Vehicle Systems

Mars Ascent Vehicle (MAV) Study Introduction: Previous Studies -Solid, liquid and hybrid rocket propulsion feasibility studies since 2011 -Focus on hybrid rocket propulsion since 2016; Reassessing Propulsion Systems for Risk Reduction - Liquid propulsion vehicle found to not be feasible; Challenges -An autonomous return mission has never been done -Mars surface environments -Platform packaging limitations -Performance and trajectory requirements; Study Team -MSFC’s Advanced Concepts Office (ACO) -MSFC propulsion and vehicle design engineering expertise -JPL MAV team.

McCollum, Lisa Tunstill↗
NASA NTRS2018

Low Temperature Hybrid Mars Ascent Vehicle Concept Development and Planning at MSFC

Return of samples from Mars has been a goal of NASA's for decades. The current Mars Sample Return mission concepts have a multiple launch rocket from the earth, where one mission delivers a caching rover to collect and package the Martian soil samples. Another rocket sends the Mars Ascent Vehicle that takes those samples to orbit. Another rocket sends an orbiter, that also meets up with the samples in orbit, and brings them back to earth. Our tasks have been focused on the Mars Ascent Vehicle. To leave the Martian surface, it requires a two burn trajectory, one to get off the planet and another to circularize the orbit. Recent studies have led to the investigation of a hybrid rocket solution. That technology has been under development for several years. This paper will discuss some of the work going on at MSFC to understand how to process the fuel, some test firings done to characterize some design features and some planning done to scope out what it would take to qualify a hybrid rocket motor for this application.

Story, George↗
NASA NTRS2018

Update on Technology Development Plan for a Low Temperature Hybrid Mars Ascent Vehicle Concept

Technology development to mature a hybrid rocket option for a potential Mars Ascent Vehicle has been underway at the Jet Propulsion Laboratory and Marshall Space Flight Center. A conceptual design was completed in 2016 and has been used to determine the motor size for risk reduction development. The task plan for the FY17 testing, actually completed in mid FY18, is discussed. The major achievement of this effort was successful full scale hotfire testing with a representative ambient Earth storable propellant combination: SP7/MON3. A near term plan, through July 2019 is briefly discussed.

Prince, Andrew↗
NASA NTRS2018

Low Temperature Hybrid Mars Ascent Vehicle Concept Development at MSFC

A hybrid propulsion system is being developed as an option for the Mars Ascent Vehicle. There are several potential advantages to this system including low temperature survivability and higher performance. Both attributes could allow a hybrid system to be a single stage to orbit vehicle, with two firings of the motor. There are some processing and manufacturing issues with the fuel and the motor that must be understood in order for the advantages of a hybrid propulsion system to be realized. This paper discusses recent progress in the manufacturing of the hybrid fuel grains and subscale test firings conducted to characterize design features at MSFC.

Story, George T.↗
NASA NTRS1999

Alternatives to Silicon Rubber Thermal Barrier in RSRM Nozzle Joints

Thiokol Propulsion encountered a situation where gas path can form in the Filler material in joints between the phenolic in the Space Shuttle Reusable Solid Rocket Motor nozzle. An investigation determined that the method for injecting the filler material into the joint created a pressurized pocket of air that forced its way to the surface while the filler was curing. The path that the air took remained open some situations leaving a path for hot gas to get deep into the joint. The condition that created the gas path has been corrected by modifications to the manufacturing process, but a design solution that would reduce processing time is being pursued. A strip of open cell installed deep into the joint, can serve as a barrier to the Filler material. Testing indicates that the foam eliminates the pressure pocket, and does not prevent detection of leakage of the o-ring seals during leak test. Open cell foam does not have thermal resistance capability and mechanical structure, which would be required in the event of a gas path. A replacement to open cell foam is now being considered. Braided carbon fiber rope has the permeability characteristics of foam and it has thermal resistance characteristics as well. Braided carbon fiber rope (BCFR) has been tested in simulated joints in subscale rocket motor. Results of the testing indicate that braided carbon fiber rope can significantly reduce gas temperature by as much es 3000 F in a nozzle joint configuration. BCFR can be installed as a barrier to stop the joint filler material or it can used as the thermal barrier alone.

Totman, Peter D.↗