Search NASA⌕ Search

Engineering topics

Prisbrey, S T

Publications and source records attributed to Prisbrey, S T.

X-ray driven implosions at ignition relevant velocities on the National Ignition Facility

Backlit convergent ablator experiments on the National Ignition Facility [E. I. Moses et al., Phys. Plasmas 16, 041006 (2009)] are indirect drive implosions that study the inflight dynamics of an imploding capsule. Side-on, backlit radiography provides data used by the National Ignition Campaign to measure time-dependent properties of the capsule ablator including its center of mass radius, velocity, and unablated mass. Previously, Callahan [D. A. Callahan et al., Phys. Plasmas 19, 056305 (2012)] and Hicks [D. H. Hicks et al., Phys. Plasmas 19, 122702 (2012)] reported backlit convergent ablator experiments demonstrating velocities approaching those required for ignition. This paper focuses on implosion performance data in the “rocket curve” plane, velocity vs. ablator mass. These rocket curve data, along with supporting numerical simulations, show that the nominal 195 μm-thick ignition capsule would reach the ignition velocity goal V = 370 km/s with low ablator mass remaining–below the goal of M = 0.25 mg. This finding led to experiments with thicker capsule ablators. A recent symmetry capsule experiment with a 20 μm thicker capsule driven by 520 TW, 1.86 MJ laser pulse (along with a companion backlit convergent ablator experiment) appears to have demonstrated V≥350 km/s with ablator mass remaining above the ignition goal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design of experiments to observe radiation stabilized Rayleigh-Taylor instability growth at an embedded decelerating interface

Using a hohlraum produced thermal x-ray drive at the National Ignition Facility (NIF) to create pressure by material ablation, a shock exceeding 200 Mbar can be driven through a planar, solid-density target and into a lower-density foam material. The shock driven through the foam is strongly radiative, and this radiation significantly alters the dynamics of the system, including those of the Rayleigh-Taylor (RT) fluid instability at the interface between the two materials. We discuss here the design of experiments that can produce such radiative conditions. One will be able to compare the observed growth rates with an extensive body of hydrodynamic experiments performed previously. In this paper, we describe a set of 1D simulations performed to understand the mechanisms of stabilization in a strongly radiative Rayleigh-Taylor unstable system. Simulation results are used to calculate modified analytic RT growth rates which have been proposed in the literature. Calculations predict reduced RT spike growth as a result of increases in density gradient scale length and mass ablation from the unstable interface. This work has direct applicability to the observable features in upcoming NIF experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

RAYLEIGH-TAYLOR STRENGTH EXPERIMENTS OF THE PRESSURE-INDUCED alpha->epsilon->alpha' PHASE TRANSITION IN IRON

We present here the first dynamic Rayleigh-Taylor (RT) strength measurement of a material undergoing solid-solid phase transition. Iron is quasi-isentropically driven across the pressure-induced bcc ({alpha}-Fe) {yields} hcp ({var_epsilon}-Fe) phase transition and the dynamic strength of the {alpha}, {var_epsilon} and reverted {alpha}{prime} phases have been determined via proton radiography of the resulting Rayleigh-Taylor unstable interface between the iron target and high-explosive products. Simultaneous velocimetry measurements of the iron free surface yield the phase transition dynamics and, in conjunction with detailed hydrodynamic simulations, allow for determination of the strength of the distinct phases of iron. Forward analysis of the experiment via hydrodynamic simulations reveals significant strength enhancement of the dynamically-generated {var_epsilon}-Fe and reverted {alpha}{prime}-Fe, comparable in magnitude to the strength of austenitic stainless steels.

36 MATERIALS SCIENCE↗

Absolute measurements of x-ray backlighter sources at energies above 10 keV

Line emission and broadband x-ray sources with x-ray energies above 10 keV have been investigated using a range of calibrated x-ray detectors for use as x-ray backlighters in high energy density (HED) experiments. The conversion efficiency of short- and long-pulse driven Mo and Ag line-emission backlighters at 17 and 22 keV was measured to investigate the crossover region between short- and long-pulse conversion efficiency. It was found that significant 17 and 22 keV line emissions were observed using a 3 {omega}, 1 ns long-pulse drive for Mo and Ag targets and a comparison between the measured Mo x-ray spectrum and calculations using an atomic physics code suggests that the line emission is due to thermal emission from N-like Mo atoms. Electron temperatures derived from fits to the continuum region of the x-ray spectra agree well with the T{sub hot} scaling as 100x(I{lambda}{sup 2}){sup 1/3}. The continuum emissions from empty and 1 atm Kr-filled imploded CH shell targets were also measured for the use as broadband backlighters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strong stabilization of the Rayleigh-Taylor instability by material strength at megabar pressures

Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity in metal foils are presented. Stabilization of RT instability (RTI) by ablation and density gradients has been studied for decades. The regime of stabilized RTI due to material strength at high pressure is new. On the Omega Laser in the Laboratory for Laser Energetics, University of Rochester, target samples of polycrystalline vanadium are compressed and accelerated quasi-isentropically at approx1 Mbar pressures, while maintaining the samples in the solid-state. Provided strong shocks are avoided, the higher the applied peak pressure, the higher the predicted foil strength, and hence, the higher the degree of strength stabilization of RTI. Several experiments were conducted where the amount of RT growth is measured by face-on radiography. The vanadium samples are probed by a laser driven He-alpha x-ray backlighter which produced 5.2 keV radiation. Comparison of the results with constitutive models for solid state strength under these conditions show that the measured RT growth is substantially lower than predictions using existing models that work well at low pressures and long time scales. High pressure, high strain rate data can be explained by the enhanced strength due to a phonon drag mechanism, creating a high effective lattice viscosity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of a Multiscale Model of Tantalum Deformation at Megabar Pressures

A new multiscale simulation tool has been developed to model the strength of tantalum under high-pressure dynamic compression. This new model combines simulations at multiple length scales to explain macroscopic properties of materials. Previously known continuum models of material response under load have built upon a mixture of theoretical physics and experimental phenomenology. Experimental data, typically measured at static pressures, are used as a means of calibration to construct models that parameterize the material properties; e.g., yield stress, work hardening, strain-rate dependence, etc. The pressure dependence for most models enters through the shear modulus, which is used to scale the flow stress. When these models are applied to data taken far outside the calibrated regions of phase space (e.g., strain rate or pressure) they often diverge in their predicted behavior of material deformation. The new multiscale model, developed at Lawrence Livermore National Laboratory, starts with interatomic quantum mechanical potential and is based on the motion and multiplication of dislocations. The basis for the macroscale model is plastic deformation by phonon drag and thermally activated dislocation motion and strain hardening resulting from elastic interactions among dislocations. The dislocation density, {rho}, and dislocation velocity, {nu}, are connected to the plastic strain rate {var_epsilon}{sup p}, via Orowan's equation: {var_epsilon}{sup p} = {rho}b{nu}/M, where b is the Burger's vector, the shear magnitude associated with a dislocation, and M is the Taylor factor, which accounts for geometric effects in how slip systems accommodate the deformation. The evolution of the dislocation density and velocity is carried out in the continuum model by parameterized fits to smaller scale simulations, each informed by calculations on smaller length scales down to atomistic dimensions. We apply this new model for tantalum to two sets of experiments and compare the results with more traditional models. The experiments are based on the Barnes's technique in which a low density material loads against a metal surface containing a pre-imposed rippled pattern. The loaded sample is Rayleigh-Taylor unstable and the rippled amplitudes grow with time. The rate of growth differs depending on the material strength, with stronger materials growing less, even to the point of saturation. One set of experiments was conducted at the pRad facility at LANSCE at Los Alamos National Laboratory in 2007 using high-explosive (HE) driven tantalum samples. The other set of experiments was done at the Omega laser at the Laboratory for Laser Energetics at the University of Rochester, which used high-powered lasers to create plasmas to dynamically compress a rippled tantalum sample. The two techniques provide data at different pressures and strain rates: The HE technique drives the samples at around 2 x 10{sup 5} s{sup -1} strain rate and pressures near 500 kbar, while the laser technique hits strain rates around 2 x 10{sup 7} s{sup -1} and pressures close to 1.4 Mbar. The most recent laser experiments were conducted in February 2010 and they present a sample of the data in Figure 1, which shows a face-on radiograph at a time of 65 ns after the laser was turned on. From this radiograph, they measure the growth factor which is defined to be the change in amplitude of the ripples relative to their initial amplitude. Figure 2 shows the resulting growth factors along with various model fits. The error bars are typically 20-25%. Only the multiscale model predictions match the experimental measurements. The growth factors via the HE technique are determined from multiple side-on proton radiography images and thus provide a full growth curve per single experiment. A sample growth curve is shown in Figure 3, also with various model fits and error bars estimated at 25%. It should be noted that by 7.5 {micro}s the growth in this sample has exceeded the initial target thickness indicating that localizations not captured in the overall simulation have probably become dominant, i.e., the target is likely breaking up. Application of the multiscale dislocation dynamics model as implemented in the Ares hydrodynamics code shows excellent agreement with both the pRad and Omega data. They also compare the Steinberg-Lund (SL), Preston-Tonks-Wallace (PTW), and Stainberg-Guinan (SG) models with the data. The PTW and SG models provide good fits to the pRad data but over-predict the growth (underestimate the strength) on the laser platform. The SL model under-predicts the pRad data and over-predicts the Omega data. The excellent agreement of the multiscale model with the data over two orders of magnitude in strain rate and more than a factor of two in pressure lends credibility to the model. They continue to stress the model by conducting experiments at 5 Mbars and beyond at the National Ignition Facility at LLNL in the near future.

36 MATERIALS SCIENCE↗

Strong stabilization of the Rayleigh-Taylor instability by material strength at Mbar pressures

Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity are presented. Using a laser created ramped drive, vanadium samples are compressed and accelerated quasi-isentropically at {approx}1 Mbar pressures, while maintaining the sample in the solid-state. Comparisons with simulations and theory indicate that the high pressure, high strain rate conditions trigger a phonon drag mechanism, resulting in the observed high effective lattice viscosity and strong stabilization of the RT instability.

42 ENGINEERING↗

Solid-state Rayleigh-Taylor experiments in vanadium at Mbar pressures at the Omega laser

We present experiments on the Rayleigh-Taylor (RT) instability in the plastic flow regime of solid-state vanadium (V) foils at {approx}1 Mbar pressures and strain rates of 10{sup 6}-10{sup 8} s{sup -1}, using a laser based, ramped-pressure acceleration technique. High pressure material strength causes strong stabilization of the RT instability at short wavelengths. Comparisons with 2D simulations utilizing models of high pressure strength show that the V strength increases by a factor of 3.5 at peak pressure, compared to its ambient strength. An effective lattice viscosity of {approx}400 poise would have a similar effect.

42 ENGINEERING↗

Rayleigh-Taylor stabilization by material strength at Mbar pressures

Studies of solid-state material dynamics at high pressures ({approx}1 Mbar) and ultrahigh strain rates (>10{sup 6} s{sup -1}) are performed using a unique laser based, quasi-isentropic high-pressure acceleration platform. Vanadium foils with pre-imposed sinusoidal ripples are accelerated in the solid state with this ramped high pressure drive. This causes Rayleigh-Taylor (RT) instability growth at the interface, where the rate of growth is sensitive to the solid-state material properties. The RT growth history is measured by face-on radiography using synchronized laser-driven x-ray backlighters at the Omega Laser. The experimental results are compared with 2D hydrodynamics simulations utilizing constitutive models of high pressure material strength. We find that the vanadium strength increases by a factor of 3.5-4 at peak pressure, compared to its ambient (undriven) strength. Both pressure hardening and strain rate hardening are the suggested cause for this increase in strength. An analysis treating strength as an effective lattice viscosity finds that a viscosity of {approx}400 poise is required to reproduce our RT data.

42 ENGINEERING↗

Measurements of preheat and shock melting in Be ablators during the first few nanoseconds of a National Ignition Facility ignition drive using the Omega laser

A scaled Hohlraum platform was used to experimentally measure preheat in ablator materials during the first few nanoseconds of a radiation drive proposed for ignition experiments at the National Ignition Facility [J. A. Paisner et al., Laser Focus World 30, 75 (1994)]. The platform design approximates the radiation environment of the pole of the capsule by matching both the laser spot intensity and illuminated Hohlraum wall fraction in scaled halfraums driven by the OMEGA laser system [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. Back surface motion measured via VISAR reflecting from the rear surface of the sample was used to measure sample motion prior to shock breakout. The experiments show that the first {approx}20 {mu}m of a Be ablator will be melted by radiation preheat, with subsequent material melted by the initial shock, in agreement with simulations. The experiments also show no evidence of anomalous heating of buried high-Z doped layers in the ablator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Progress towards materials science above 1000 GPa (10 Mbar) on the NIF laser

Solid state dynamics experiments at extreme pressures, P > 1000 GPa (10 Mbar), and ultrahigh strain rates (1.e6-1.e8 1/s) are being developed for the National Ignition Facility (NIF) laser. These experiments will open up exploration of new regimes of materials science at an order of magnitude higher pressures than have been possible to date. Such extreme, solid state conditions can be accessed with a ramped pressure drive. The experimental, computational, and theoretical techniques are being developed and tested on the Omega laser. Velocity interferometer measurements (VISAR) establish the high pressure conditions generated by the ramped drive. Constitutive models for solid state strength under these conditions are tested by comparing simulations with experiments measuring perturbation growth from the Rayleigh-Taylor instability in solid state samples of vanadium. Radiography techniques using synchronized bursts of x-rays have been developed to diagnose this perturbation growth. Experiments on Omega demonstrating these techniques at peak pressures of {approx}1 Mbar will be discussed. The time resolved observation of foil cracking and void formation show the need for tamped samples and a planar drive.

42 ENGINEERING↗

Diamond at 800 GPa

A new compression technique, which enables the study of solids into the TPa regime, is described and used to ramp (or quasi-isentropically) compress diamond to a peak pressure of 1400 GPa. Diamond stress versus density data are reported to 800 GPa and suggest that the diamond phase is stable and has significant material strength up to at least this stress level. Data presented here are the highest ramp compression pressures by more than a factor of 5 and the highest-pressure solid equation-of-state data ever reported.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗