Engineering topics

Proctor, M. P.

Publications and source records attributed to Proctor, M. P..

9 records

NASA NTRS2002

Two- and Three-Dimensional Numerical Experiments Representing Two Limiting Cases of an In-Line Pair of Finger Seal Components

The work presented here concerns the numerical development and simulation of the flow, pressure patterns and motion of a pair of fingers arranged behind each other and axially aligned in-line. The fingers represent the basic elemental component of a Finger Seal (FS) and form a tight seal around the rotor. Yet their flexibility allows compliance with rotor motion and in a passive-adaptive mode complies also with the hydrodynamic forces induced by the flowing fluid. While the paper does not treat the actual staggered configuration of a finger seal, the inline arrangement represents a first step towards that final goal. The numerical 2-D (axial-radial) and 3-D results presented herein were obtained using a commercial package (CFD-ACE+). Both models use an integrated numerical approach, which couples the hydrodynamic fluid model (Navier-Stokes based) to the solid mechanics code that models the compliance of the fingers.

Braun, M. J.↗

NASA NTRS1992

Development of advanced seals for space propulsion turbomachinery

Current activities in seals for space propulsion turbomachinery that the NASA Lewis Research Center sponsors are surveyed. The overall objective is to provide the designer and researcher with the concepts and the data to control seal dynamics and leakage. Included in the program are low-leakage seals, such as the brush seal, the 'ceramic rope' seal, low-leakage seals for liquid oxygen turbopumps, face seals for two phase flow, and swirl brakes for stability. Two major efforts are summarized: a seal dynamics in rotating machinery and an effort in seal code development.

Hendricks, R. C.↗

NASA NTRS1991

Some preliminary results of brush seal/rotor interference effects on leakage at zero and low rpm using a tapered-plug rotor

Some preliminary brush seal leakage results for ambient-temperature air are presented. Data for four nominal brush-rotor radial clearances of -0.09, -0.048, -0.008, and 0.035 mm were taken by using a tapered plug rotor at 0 and 400 rpm with rotor runout of 0.127 mm peak to peak. The brush seal nominal bore diameter was 38 mm with 0.05-mm bristles at 200 bristles/mm of circumference and a 0.61-mm fence height. Leakages were greater than predicted, but agreement was reasonable. Leakage rates were not significantly altered by hysteresis or inlet flow variations. Visualization studies showed that the bristles followed the 400-rpm excitation, and loading studies indicated that bristles slid relative to one another.

Hendricks, R. C.↗

NASA NTRS1991

Some preliminary results of brush seal/rotor interference effects on leakage at zero and low RPM using a tapered-plug rotor

Some preliminary brush seal leakage results for ambient temperature air are presented. Data for four nominal brush rotor radial clearances of -0.09, -0.048, -0.008, and 0.035 mm were taken by using a tapered plug rotor at 0 and 400 rpm with rotor runout of 0.127 mm peak to peak. The brush seal nominal bore diameter was 38 mm with 0.05 mm bristles at 200 bristles/mm of circumference and a 0.61 mm fence height. Leakages were greater than predicted, but agreement was reasonable. Leakage rates were not significantly altered by hysteresis or inlet flow variations. Visualization studies showed that the bristles followed the 400 rpm excitation, and loading studies indicated that bristles slid relative to one another.

Hendricks, R. C.↗

NASA NTRS1985

Transient technique for measuring heat transfer coefficients on stator airfoils in a jet engine environment

A transient technique was used to measure heat transfer coefficients on stator airfoils in a high-temperature annular cascade at real engine conditions. The transient response of thin film thermocouples on the airfoil surface to step changes in the gas stream temperature was used to determine these coefficients. In addition, gardon gages and paired thermocouples were also utilized to measure heat flux on the airfoil pressure surface at steady state conditions. The tests were conducted at exit gas stream Reynolds numbers of one-half to 1.9 million based on true chord. The results from the transient technique show good comparison with the steady-state results in both trend and magnitude. In addition, comparison is made with the STAN5 boundary layer code and shows good comparison with the trends. However, the magnitude of the experimental data is consistently higher than the analysis.

Gladden, H. J.↗

NASA NTRS1985

Combustor flame flashback

A stainless steel, two-dimensional (rectangular), center-dump, premixed-prevaporized combustor with quartz window sidewalls for visual access was designed, built, and used to study flashback. A parametric study revealed that the flashback equivalence ratio decreased slightly as the inlet air temperature increased. It also indicated that the average premixer velocity and premixer wall temperature were not governing parameters of flashback. The steady-state velocity balance concept as the flashback mechanism was not supported. From visual observation several stages of burning were identified. High speed photography verified upstream flame propagation with the leading edge of the flame front near the premixer wall. Combustion instabilities (spontaneous pressure oscillations) were discovered during combustion at the dump plane and during flashback. The pressure oscillation frequency ranged from 40 to 80 Hz. The peak-to-peak amplitude (up to 1.4 psi) increased as the fuel/air equivalence ratio was increased attaining a maximum value just before flashback. The amplitude suddenly decreased when the flame stabilized in the premixer. The pressure oscillations were large enough to cause a local flow reversal. A simple test using ceramic fiber tufts indicated flow reversals existed at the premixer exit during flickering. It is suspected that flashback occurs through the premixer wall boundary layer flow reversal caused by combustion instability. A theoretical analysis of periodic flow in the premixing channel has been made. The theory supports the flow reversal mechanism.

Proctor, M. P.↗

NASA NTRS1985

Transient technique for measuring heat transfer coefficients on stator airfoils in a jet engine environment

Gladden, H. J.↗

NASA NTRS1985

Flame flashback in a premixed dump combustor

A stainless steel, rectangular center-dump, premixed-prevaporized combustor was used at the NASA Lewis Research Center to study flashback in controlled conditions simulating gas turbine combustor operations under steady-state and transient conditions. The combustor allowed visual access to the combustion area, and was operated at inlet air temperatures from 600 to 850 K, premixer wall temperatures from 450 to 900 K, and average premixer velocity from 40 to 80 ft/s. A parametric study revealed a slight decrease in the flashback equivalence ratio as the inlet air temperatures increased. It also indicated that the premixer wall temperature and premixer velocity are not governing parameters of flashback. It is suggested that flashback occurs through the premixer wall boundary layer flow reversal caused by combustion instability.

Proctor, M. P.↗

NASA NTRS1984

Combustor flame flashback

Flashback, a problem that occurs in premixed-prevaporized combustors, is the upstream propagation of the flame from the combustor into the premixing tubes. Not only does flashback change the combustion process from premixed burning to diffusion burning, thus creating more pollutants, but it also inflicts considerable damage to the fuel injector, premixing tube and other equipment upstream. The conditions at which flashback occurs in steady burning and the mechanism that causes flashback in both steady and transient flow are studied. The equivalence ratio at which flashback occurs is being measured for inlet temperatures of 600-950 K, premixer wall temperatures of 450-1050 K and premixer velocities of 40-80 ft/s. These data are presented.

Proctor, M. P.↗