Defects in Hydrothermally Synthesized LiFePO[subscript 4] and LiFe[subscript 1-x]Mn[subscript x]PO[subscript 4] Cathode Materials
Abstract not provided
Engineering topics
Publications and source records attributed to Proffen, Thomas.
Abstract not provided
Kaolinite intercalated with potassium acetate is of great interest in the areas of environmental remediation and industrial application; however, its exact atomic structure and the changes which occur when heated have remained largely elusive. Here, neutron pair distribution function analysis is used to investigate the local structural characteristics of this complex material, revealing that hydrated potassium acetate exists as a single layer in the interlamellar spacing of kaolinite. Furthermore, the potassium ions within the intercalated complex are most likely associated with the resonance structure of the acetate molecules, and upon heating (and decomposition of the carbon containing molecules), these ions become strongly associated with the negative charge located on the oxygen atoms in the alumina layers of dehydroxylated kaolinite. Several possible orientations of hydrated potassium acetate within the interlamellar spacing of kaolinite have been proposed and investigated using density functional modeling, revealing the complex nature of this material. Nevertheless, this investigation has shown that the dehydroxylated form of the intercalated compound contains highly strained alumina and available alkali (potassium), making it a viable alternative to traditional aluminosilicates.
The decomposition of hexacarbonyltungsten, W(CO){sub 6}, has been studied. The decomposition was induced by heating W(CO){sub 6} in an autoclave at 523 K and pressures up to 1.8 MPa, and by laser heating in a diamond anvil cell at pressures between 5 and 18 GPa. The products have been characterized using synchrotron X-ray diffraction, pair distribution function analysis, Raman spectroscopy and scanning electron microscopy. Decomposition in the autoclave at the lower pressures resulted in the formation of a metastable tungsten carbide, W{sub 2}C, with an average particle size of 1-2 nm, and an unidentified nanocrystalline tungsten oxide and nanocrystalline graphite with average particle sizes of 1-2 and 11 nm, respectively. The existence of nanocrystalline graphite was deduced from micro-Raman spectra and the graphite particle size was extracted from the intensities of the Raman modes. The high-pressure decomposition products obtained in the diamond anvil cell are the monoclinic tungsten oxide phase WO{sub 2} and the high-pressure phase W{sub 3}O{sub 8}(I). The approximate average size of the graphite particles formed here was 6-8 nm. The bulk modulus of W(CO){sub 6} is B{sub 0} {approx_equal} 13 GPa.
Understanding the atomic-level changes that occur as kaolinite is converted (thermally dehydroxylated) to metakaolin is critical to the optimization of this large-scale industrial process. Metakaolin is X-ray amorphous; therefore, conventional crystallographic techniques do not reveal the changes in local structure during its formation. Local structure-based experimental techniques are useful in understanding the atomic structure but do not provide the thermodynamic information which is necessary to ensure plausibility of refined structures. Here, kaolinite dehydroxylation is modeled using density functional theory, and a stepwise methodology, where several water molecules are removed from the structure, geometry optimization is carried out, and then the process is repeated. Hence, the structure remains in an energetically and thermodynamically feasible state while transitioning from kaolinite to metakaolin. The structures generated during the dehydroxylation process are validated by comparison with X-ray and neutron pair distribution function data. Thus, this study illustrates one possible route by which dehydroxylation of kaolinite can take place, revealing a chemically, energetically, and experimentally plausible structure of metakaolin. This methodology of density functional modeling of the stepwise changes in a material is not limited in application to kaolinite or other aluminosilicates and provides an accurate representation of the local structural changes occurring in materials used in industrially important processes.
Differently weighted experimental scattering data have been used to extract partial or differential structure factors or pair distribution functions in studying many materials. However, this is not done routinely partly because of the lack of user-friendly software. This paper presents MIXSCAT, a new member of the DISCUS program package. MIXSCAT allows one to combine neutron and X-ray pair distribution functions and extract their respective differential functions.
Very little experimental work has conclusively explored the structural transformation between the amorphous and metastable crystalline phases of phase change chalcogenides. A recent flurry of theoretical work has supported likely mechanisms for the phase transition process in Ge-Sb-Te (GST) compositions and invigorated efforts at probing local atomic arrangements experimentally. The pair distribution function (PDF) formalism of total scattering data provides directly both local structure correlations at low real-space dimensions, and intermediate range order at higher length scales, a distinct advantage for following the relevant phase transition in phase change materials (PCM). A challenge facing the field is the difficulty in distinguishing separate peak contributions to pair correlation functions in amorphous and highly disordered samples. For example, various types of local order have been reported for Ge{sub x}Te{sub 1-x} phases, including both random mixtures and discrete structural units, and both 4-fold and 6-fold coordination around Ge. We describe our efforts in advancing capabilities for extracting and refining differential or partial pair distribution function data sets by combining neutron and x-ray total scattering, with extensions to isotopic substitution and anomalous x-ray scattering. Our results combining neutron and x-ray scattering for the Ge{sub x}Te{sub 1-x} series, for example, clearly distinguish Ge-Te and Te-Te contributions in nearest neighbor correlations. Presenting an additional challenge, phase change materials with fast switching speeds (those arguably of greatest technological interest) have stable bulk crystalline phases and do not readily form glasses until reduced to small dimensions. Thin film samples are inherently difficult to probe with conventional crystallographic methods. We demonstrate successful synchrotron x-ray total scattering experiments for PCM thin films with thicknesses between 100 nm and 1 um and describe how chemical short-range order and local bonding environments vary in amorphous, metastable and crystalline GeSb{sub 2}Te{sub 4} films. Total scattering methods for powders and thin films allow for a direct comparison of PCM properties (crystallization temperature, optical contrast between phases, phase change speed, etc.) with observed local structure and motivate further exploration into the atomic configurations enabling this fascinating class of materials.