Engineering topics
Pugh, Michael
Publications and source records attributed to Pugh, Michael.
Ka-band High-Rate Downlink System for the NISAR Mission
This paper provides a description and analyses of the high-rate Ka-band telecom system for the upcoming NISAR (NASA-ISRO Synthetic Aperture Radar) mission. NISAR is a collaborative Earth-Science mission between National Aeronautics and Space Administration (NASA) and Indian Space Research Organization (ISRO), which features an L-band SAR instrument and an S-band SAR instrument. The simultaneous dual-frequency radar system at peak rates will produce data at gigabit-per-second speeds, which drives the data-volume requirements. The key driving requirement for the payload communication subsystem is to provide a minimum of 26 Terabits per day of radar science data to the ground. The high-rate transmitter on the flight system is a software-defined radio developed at the Jet Propulsion Laboratory (JPL), based on the Universal Space Transponder platform, providing an offset quadrature phase shift key modulated waveform with Low-Density Parity-Check encoding of the data transfer frames. Two transmitters used in a dual-polarization configuration with each transmitter providing two giga-symbols per second (Gsps) of coded data provides an aggregate rate of four Gsps. In this system, only one watt of signal power is necessary on each polarization to overcome propagation losses and achieve a successful RF link. Several Near Earth Network (NEN) ground station sites (Alaska in the United States, Svalbard in Norway, and Punta Arenas in Chile) are baselined for the space-to-Earth communications link. Each ground station will also feature multiple upgrades to support NISAR’s transmission starting with new Ka-band antennas, wideband downconverters and high-rate receivers. In addition, a baseband data processor called Data Acquisition Processor and Handling Network Environment (DAPHNE), newly developed by the NEN, provides data storage and connectivity to backhaul networks. With NISAR’s large quantities of data (over 3.5 Petabytes over the mission), the processing of science data will be primarily performed on a cloud system to reduce the overall cost to the mission. The system described herein will be the first operational use of Gsps-class downlink rates on an Earth-Science mission.
High-Rate Ka-Band Modulator for the NISAR Mission
In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.
The Universal Space Transponder: A Next Generation Software Defined Radio
The Universal Space Transponder (UST) is a next generation transponder developed at the Jet Propulsion Laboratory to meet a large variety of telecom, navigation, and radio science needs for future deep-space and near-Earth missions. This paper details the UST software defined radio design and describes how the combination of a modular hardware architecture and in-flight reprogrammability enables a new level of flexibility and expandability for a space transponder. The UST uses common power and digital processing assemblies that can be integrated with a variety of RF modules and is capable of simultaneous, multiband operations with data rates up to 37.5 Mbps RX and 300 Mbps TX. This allows a single radio to support all the direct-to-Earth and relay communication requirements for even complex mission scenarios, reducing the total cost, mass, and power. The discussion includes a description of the current UST engineering models that have been built and tested, as well as details about the next generation capabilities supported by UST, including advanced link coding and modulation, radiometric techniques, and in-radio protocol handling. Details are also presented on RF modules and digital processing in development for radio science and astronomy purposes, including a bistatic radar receiver and broadband planetary emissions receiver. These will demonstrate the ability to integrate low-cost science instruments into the UST architecture, further expanding the versatility of the UST.