Search NASA⌕ Search

Engineering topics

Pulsonetti, M. V.

Publications and source records attributed to Pulsonetti, M. V..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Boundary Layer Protuberance Simulations in Channel Nozzle Arc-Jet

Two protuberance designs were modeled in the channel nozzle of the NASA Johnson Space Center Atmospheric Reentry Materials and Structures Facility with the Data-Parallel Line Relaxation computational fluid dynamics code. The heating on the protuberance was compared to nominal baseline heating at a single fixed arc-jet condition in order to obtain heating augmentation factors for flight traceability in the Boundary Layer Transition Flight Experiment on Space Shuttle Orbiter flights STS-119 and STS-128. The arc-jet simulations were performed in conjunction with the actual ground tests performed on the protuberances. The arc-jet simulations included non-uniform inflow conditions based on the current best practices methodology and used variable enthalpy and constant mass flow rate across the throat. Channel walls were modeled as fully catalytic isothermal surfaces, while the test section (consisting of Reaction Cured Glass tiles) was modeled as a partially catalytic radiative equilibrium wall. The results of the protuberance and baseline simulations were compared to the applicable ground test results, and the effects of the protuberance shock on the opposite channel wall were investigated.

Marichalar, J. J.↗
NASA NTRS2009

Boundary Layer Transition Protuberance Tests at NASA JSC Arc-Jet Facility

A series of arc-jet tests in support of the Shuttle Orbiter Boundary Layer Transition flight experiment was conducted in the Channel Nozzle of the NASA Johnson Space Center Atmospheric Reentry Materials and Structures Facility. The boundary layer trip was a protrusion of a certain height and geometry fabricated as part of a 6"x6" tile insert, a special test article made of the Boeing Rigid Insulation tile material and coated with the Reaction Cured Glass used for the bottom fuselage tiles of the Space Shuttle Orbiter. A total of five such tile inserts were manufactured: four with the 0.25-in. trip height, and one with the 0.35-in. trip height. The tile inserts were interchangeably installed in the center of the 24"x24" variable configuration tile array mounted in the 24"x24" test section of the channel nozzle. The objectives of the test series were to demonstrate that the boundary layer trip can safely withstand the Space Shuttle Orbiter flight-like re-entry environments and provide temperature data on the protrusion surface, surfaces of the nearby tiles upstream and downstream of the trip, as well as the bond line between the tiles and the structure. The targeted test environments were defined for the tip of the protrusion, away from the nominal surface of the tile array. The arc jet test conditions were approximated in order to produce the levels of the free stream total enthalpy at the protrusion height similar to those expected in flight. The test articles were instrumented with surface, sidewall and bond line thermocouples. Additionally, Tempilaq temperature-indicating paint was applied to the nominal tiles of the tile array in locations not interfering with the protrusion trip. Five different grades of paint were used that disintegrate at different temperatures between 1500 and 2000 deg F. The intent of using the paint was to gauge the RCG-coated tile surface temperature, as well as determine its usefulness for a flight experiment. This paper provides an overview of the channel nozzle arc jet, test articles and test conditions, as well as the results of the arc-jet tests including the measured temperature response of the test articles, their pre- and post-test surface scans, condition of the thermal paint, and continents on the protrusion tip heating achieved in tests compared to the computational fluid dynamics predictions.

Larin, M. E.↗
NASA NTRS2009

Boundary Layer Protuberance Simulations in Channel Nozzle Arc Jet

Various protuberance heights and shapes were modeled in the channel nozzle of the NASA Johnson Space Center Atmospheric Reentry Materials and Strictures Facility with the Data- Parallel Line Relaxation computational fluid dynamics code. The heating on the protuberance was compared to baseline (no protuberance) heating at a single fixed arc jet condition in order to obtain heating augmentation factors that will be used for flight traceability in the Boundary Layer Transition Flight Experiment on Space Shuttle Orbiter flights STS-119 (completed) and STS-128 (future flight). The arc jet simulations were performed in conjunction with the actual ground tests performed on the flight version (selected height and shape) of the protuberance. Thearc jet simulations for the final (flight version) protuberance included non-uniform inflow conditions beginning at the channel nozzle throat. The 2D inflow condition was modeled based on the current best practices methodology and used variable enthalpy and mass flow rate across the throat. Channel walls were modeled as fully catalytic isothermal surfaces, while the test section (consisting of Reaction Cured Glass tiles) was modeled as a partially catalytic radiative equilibrium wall. The results of the protuberance and baseline simulations were compared to the applicable ground test results. In addition, the obtained heating augmentation factors were compared to the factors derived from the STS-119 flight data. The effects of the protuberance shock on the opposite channel wall were also investigated.

Larin, M. E.↗
NASA NTRS1995

Scaling in a scramjet combustor

Studies of scramjet combustor scaling have been extended to include testing of a 'small' combustor, thereby allowing comparison with results obtained in a 'large' combustor of nearly identical configuration. The scale of the two combustors varied by a factor of 5. It was anticipated that the combustion process would scale as the product of pressure with length if the temperature, the Mach number, the velocity, the free stream composition and the equivalence ratio were the same. To achieve this while allowing for the necessary difference in pressure the two models were tested with different shock tunnel nozzles. The large was tested in a M = 8 nozzle, with an intake consisting of a pair of opposing wedges preceding the model, which produced shocks to reduce the Mach number to approximately 3.4 before the flow entered the model inlet. It was then expanded to raise the Mach number again. The small model was tested in a M = 4 nozzle, with the nozzle flow passing directly to the inlet of the model. The wedge intake for the large model was adjusted to yield similar combustion chamber Mach number for both models. Then, by matching the stagnation enthalpy, it was possible also to match the temperature and the velocity. The free stream composition was matched by operating at the same nozzle supply pressure. Wall pressure distributions were measured along each of the ducts. The pressure is normalized with respect to the pressure measured at the point opposite to the injector exit, and the distance downstream of the exit is normalized with respect to the height of the duct. It can be seen that, when normalized in this manner, both ducts produce quantitatively similar pressure distributions, confirming the initial hypothesis that the combustion process would scale as the product of pressure with length.

Pulsonetti, M. V.↗
NASA NTRS1993

Shock tunnel studies of scramjet phenomena, supplement 7

Reports by the staff of the University of Queensland on various research studies related to the advancement of scramjet technology are presented. These reports document the tests conducted in the reflected shock tunnel T4 and supporting research facilities that have been used to study the injection, mixing, and combustion of hydrogen fuel in generic scramjets at flow conditions typical of hypersonic flight. In addition, topics include the development of instrumentation and measurement technology, such as combustor wall shear and stream composition in pulse facilities, and numerical studies and analyses of the scramjet combustor process and the test facility operation. This research activity is Supplement 7 under NASA Grant NAGW-674.

Bakos, R. J.↗
NASA NTRS1993

Shock tunnel studies of scramjet phenomena, supplement 8

Reports by the staff of the University of Oueensland on various research studies related to the advancement of scramjet technology are presented. These reports document the tests conducted in the reflected shock tunnel T4 and supporting research facilities that have been used to study the injection, mixing, and combustion of hydrogen fuel in generic scramjets at flow conditions typical of hypersonic flight. In addition, topics include the development of instrumentation and measurement technology, such as combustor wall shear and stream composition in pulse facilities, and numerical studies and analyses of the scramjet combustor process and the test facility operation. This research activity is Supplement 8 under NASA Grant NAGW-674.

Stalker, R. J.↗
NASA NTRS1990

Hypersonic Mixing and Combustion Studies in the GASL HYPULSE Facility

Hydrogen-air mixing and combustion experiments at air velocities approaching 17,000 ft/s have been conducted in the expansion tube in CASL's HYPULSE facility. The data were obtained in the facility's sub-millisecond steady flow test period. The results proved to be repeatable and indicated increasing extent of reaction as the fuel-air ratio was increased from stoichiometric to three times stoichiometric. Comparisons were made with the results from a one-dimensional, finite-rate chemistry code and from one-dimensional cycle codes which assume equilibrium chemistry. These comparisons indicate that the magnitudes and trends of the measured longitudinal pressure distributions are predicted by the one-dimensional codes provided that the relevant physical phenomena are accounted for in the computations.

Bakos, R. J.↗