Engineering topics

Qu, K.

Publications and source records attributed to Qu, K..

4 records

DOE OSTI2022

Particle deceleration for collective QED signatures

Frequency upshifts have been proposed as a first experimental signature of collective effects in quantum electrodynamic cascade generated electron–positron pair plasmas. Since the high effective masses of generated pairs will reduce any frequency change, stopped pairs at a minimal Lorentz factor in the lab frame were thought to be the dominant contribution to the laser upshift. However, we demonstrate that only considering stopped particles unduly neglects the contributions of particles re-accelerated in the laser propagation direction. Re-accelerated particles should, on a per particle basis, affect the laser more strongly and over a much longer timescale. To maximize particle contributions to the laser upshift, we consider a Laguerre–Gaussian (LG) mode laser beam to better reflect generated pairs. Furthermore, the LG mode does not have an advantage in particle deceleration and re-acceleration when compared against a Gaussian beam, but the LG mode can maintain particle contributions for a longer duration, allowing for more pair density accumulation. Deceleration with a structured beam to keep pairs within the laser should create a larger upshift, thereby lowering the demands on the driving laser.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Modulation-slippage trade-off in resonant four-wave upconversion

Following up on a proposal to use four-wave mixing in an underdense plasma at mildly relativistic laser intensities to produce vastly more energetic x-ray pulses [V. M. Malkin and N. J. Fisch, Phys. Rev. E, 101, 023211 (2020)], we perform the first numerical simulations in one dimension to illustrate amplification of a short high frequency seed through four-wave mixing. Here, we illustrate how parasitic processes including phase modulation and spatial pulse slippage limit the amplification efficiency. Although the regimes studied were not where the optimal efficiencies were expected, these regimes do expose the basic physical processes at play, while still yielding not insignificant spectral power upshift.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Suppression of power losses during laser pulse propagation in underdense plasma slab

For current state-of-the-art terawatt lasers, the primary laser scattering mechanisms in plasma include Forward Raman Scattering (FRS), excitation of plasma waves, and the self-modulational instability (SMI). Using 2D PIC simulations, we demonstrate the dominance of the FRS in the regime with medium-to-low density plasma and non-relativistic laser fields. However, the use of multi-colored lasers with frequency detuning exceeding the plasma frequency, Δω > ω pe , suppresses the FRS. Finally, the laser power can then be transmitted efficiently.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2020

Design of a V–Ti–Ni alloy with superelastic nano-precipitates

Stress-induced martensitic transformations enable metastable alloys to exhibit enhanced strain hardening capacity, leading to improved formability and toughness. As is well-known from transformation-induced plasticity (TRIP) steels, however, the resulting martensite can limit ductility and fatigue life due to its intrinsic brittleness. In this work, we explore an alloy design strategy that utilizes stress-induced martensitic transformations but does not retain the martensite phase. This strategy is based on the introduction of superelastic nano-precipitates, which exhibit reverse transformation after initial stress-induced forward transformation. To this end, utilizing ab-initio simulations and thermodynamic calculations we designed and produced a V 45 Ti 30 Ni 25 (at%) alloy. In this alloy, TiNi is present as nano-precipitates uniformly distributed within a ductile V-rich base-centered cubic (bcc) β matrix, as well as being present as a larger matrix phase. We characterized the microstructure of the produced alloy using various scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Furthermore, the bulk mechanical properties of the alloy are demonstrated through tensile tests, and the reversible transformation in each of the TiNi morphologies were confirmed by in-situ TEM micro-pillar compression experiments, in-situ high-energy diffraction synchrotron cyclic tensile tests, indentation experiments, and differential scanning calorimetry experiments. The observed transformation pathways and variables impacting phase stability are critically discussed.

59 BASIC BIOLOGICAL SCIENCES↗