Engineering topics

Quentmeyer, Richard J.

Publications and source records attributed to Quentmeyer, Richard J..

8 records

NASA NTRS1993

Hot-gas-side heat transfer characteristics of subscale, plug-nozzle rocket calorimeter chamber

An experimental investigation was conducted to determine the hot-gas-side heat transfer characteristics for a liquid-hydrogen-cooled, subscale, plug-nozzle rocket test apparatus. This apparatus has been used since 1975 to evaluate rocket engine advanced cooling concepts and fabrication techniques, to screen candidate combustion chamber liner materials, and to provide data for model development. In order to obtain the data, a water-cooled calorimeter chamber having the same geometric configuration as the plug-nozzle test apparatus was tested. It also used the same two showerhead injector types that were used on the test apparatus: one having a Rigimesh faceplate and the other having a platelet faceplate. The tests were conducted using liquid oxygen and gaseous hydrogen as the propellants over a mixture ratio range of 5.8 to 6.3 at a nominal chamber pressure of 4.14 MPa abs (600 psia). The two injectors showed similar performance characteristics with the Rigimesh faceplate having a slightly higher average characteristic-exhaust-velocity efficiency of 96 percent versus 94.4 percent for the platelet faceplate. The throat heat flux was 54 MW/m(sup 2) (33 Btu/in.(sup 2)-sec) at the nominal operating condition, which was a chamber pressure of 4.14 MPa abs (600 psia), a hot-gas-side wall temperature of 730 K (1314 R), and a mixture ratio of 6.0. The chamber throat region correlation coefficient C(sub g) for a Nusselt number correlation of the form Nu =C(sub g)Re(sup 0.8)Pr(sup 0.3) averaged 0.023 for the Rigimesh faceplate and 0.026 for the platelet faceplate.

Quentmeyer, Richard J.↗

NASA NTRS1992

An experimental investigation of high-aspect-ratio cooling passages

An experimental investigation was conducted to evaluate the effectiveness of using high-aspect-ratio cooling passages to improve the life and reduce the coolant pressure drop in high-pressure rocket thrust chambers. A plug-nozzle rocket-engine test apparatus was used to test two cylindrical chambers with low-aspect-ratio cooling passages and one with high-aspect-ratio cooling passages. The chambers were cyclically tested and data were taken over a wide range of coolant mass flows. The results showed that for the same coolant pressure drop, the hot-gas-side wall temperature of the high-aspect-ratio chamber was 30 percent lower than the baseline low-aspect-ratio chamber, resulting in no fatigue damage to the wall. The coolant pressure drop for the high-aspect-ratio chamber was reduced in increments to one-half that of the baseline chamber, by reducing the coolant mass flow, and still resulted in a reduction in the hot-gas-side wall temperature when compared to the low-aspect-ratio chambers.

Carlile, Julie A.↗

NASA NTRS1992

An experimental investigation of high-aspect-ratio cooling passages

An experimental investigation was conducted to evaluate the effectiveness of using high-aspect-ratio cooling passenges to improve the life and reduce the colant pressure drop in high-pressure rocket thrust chambers. A plug-nozzle rocket-engine test apparatus was used to test two cylindrical chambers with low-aspect-ratio cooling passages and one with high-aspect-ratio cooling passages. The chambers were cyclically tested and data were taken over a wide range of coolant mass flows. The results showed that for the same coolant pressure drop, the hot-gas-side wall temperature of the high-aspect-ratio chamber was 30 percent lower than the baseline low-aspect-ratio chamber, resulting in no fatigue damage to the wall. The coolant pressure drop for the high-aspect-ratio chamber was reduced in increments to one-half that of the baseline chamber, by reducing the coolant mass flow, and still resulted in a reduction in the hot-gas-side wall temperature when compared to the low-aspect-ratio chambers.

Carlile, Julie A.↗

NASA NTRS1990

Rocket combustion chamber life-enhancing design concepts

NASA continues to pursue technologies which can lead to an increase in life and reduce the costs of fabrication of the Space Shuttle Main Engine. The joint NASA/Air Force Advanced Launch System Program has set its prime objectives to be high reliability and low cost for their new advanced booster engine. In order to meet these objectives, NASA will utilize the results of several ongoing programs to provide the required technologies. An overview is presented of those programs which address life enhancing design concepts for the combustion chamber. Seven different design concepts, which reduce the thermal strain and/or increase the material strength of the combustion chamber liner wall are discussed. Subscale rocket test results are presented, where available, for life enhancing design concepts. Two techniques for reducing chamber fabrication costs are discussed, as well as issues relating to hydrocarbon fuels/combustion chamber liner materials compatibility.

Quentmeyer, Richard J.↗

NASA NTRS1989

Adherent Thermal Barrier For Combustion Chamber

In improved method, fabrication begins with machining of aluminum mandrel to requisite cylindrical shape. Heat-barrier coating - yttria-stablized zirconia - plasma-sprayed on mandrel to thickness of 0.076 mm. Nickel/chromium layer about 0.025 mm thick sprayed on zirconia. Thin zirconia coating reduces maximum operating temperature of copper wall of chamber from 844 to 334 K. At lower temperature, copper liner stronger and undergoes less strain and less tendency to distort and crack.

Quentmeyer, Richard J.↗

NASA NTRS1989

Thrust chamber thermal barrier coating techniques

Methods for applying thermal barrier coatings to the hot-gas side wall of rocket thrust chambers in order to significantly reduce the heat transfer in high heat flux regions has been the focus of technology efforts for many years. A successful technique developed by NASA-Lewis that starts with the coating on a mandrel and then builds the thrust chamber around it by electroforming appropriate materials is described. This results in a smooth coating with exceptional adherence, as was demonstrated in hot fire rig tests. The low cycle fatigue life of chambers with coatings applied in this manner was increased dramatically compared to uncoated chambers.

Quentmeyer, Richard J.↗

NASA NTRS1988

Thrust chamber thermal barrier coating techniques

Methods for applying thermal barrier coatings to the hot-gas side wall of rocket thrust chambers in order to significantly reduce the heat transfer in high heat flux regions was the focus of technology efforts for many years. This paper describes a successful technique developed by the Lewis Research Center that starts with the coating of a mandrel and then builds the thrust chamber around it by electroforming appropriate materials. This results in a smooth coating with exceptional adherence, demonstrated in hot fire rig tests. The low cycle fatigue life of chambers with coatings applied in this manner was increased dramatically compared to uncoated chambers.

Quentmeyer, Richard J.↗

NASA NTRS1962

Performance Evaluation of Fixed- and Variable-Area Rocket Exhaust Diffusers Using Single and Clustered Nozzles with and Without Gimbaling

An investigation of exhaust diffusers used for altitude simulation in testing rocket engines was conducted with model diffusers and gaseous nitrogen as the working fluid. This investigation was conducted to evaluate the effects on performance of gimbaling clustered nozzles in a single fixed-area exhaust diffuser. A two-nozzle cluster was gimbaled in all attitudes in four different exhaust-diffuser configurations: (1) a straight circular tube, (2) a straight figure-eight tube, (3) a circular tube with a second throat, and (4) a figure-eight tube with a second throat. Gimbaling clustered nozzles had little effect on the operating pressure ratio for either straight-tube or second-throat diffusers, but caused a large increase in the starting-pressure-ratio requirements in some straight-tube exhaust diffusers. The performance of two or four clustered nozzles with no gimbaling was compared with single-nozzle performance on the basis of the ratio of diffuser area to nozzle-throat area. The performance was found to be dependent on the diffuser- to nozzle-throat-area ratio and independent of both the number of primary nozzles and the nozzle-area ratio. A separate investigation was also conducted to evaluate the performance improvement obtainable with a variable-area exhaust diffuser. This type of diffuser achieved a 26-percent reduction in starting pressure ratio, a 40-percent reduction in operating pressure ratio, and a 50-percent reduction in the overall diffuser length over the values attainable with a fixed-area second-throat diffuser.

ROCKET↗