Search NASA⌕ Search

Engineering topics

Rabinovitch, Jason

Publications and source records attributed to Rabinovitch, Jason.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Validation of a High-Fidelity Supersonic Parachute Inflation Dynamics Model and Best Practice

The parachute inflation dynamics (PID) of a Disk-Gap-Band (DGB) parachute system travelling at supersonic velocities in the high-altitude Earth atmosphere is simulated using a high-fidelity, multiphysics, massively-parallel computational framework. The sensitivity of the simulation results with respect to critical modelling and simulation parameters, including the fluid mechanical governing equations (Euler vs Navier-Stokes with RANS turbulence closure vs Navier-Stokes with LES turbulence closer), the interaction between the flow and the suspension lines (accounted for vs not accounted for), the dynamics of the payload (restrained vs free), and the material model of the heterogeneous fabric canopy (Saint-Venant Kirchoff vs mechanics-informed multiscale neural network), is extensively investigated. The parameter investigation is enabled by advancements to the state-of-the-art in the modelling and simulation of the supersonic parachute inflation process, which are presented as part of the computational framework. The predictive quality of the computational framework in the context of supersonic PID is validated by comparison of the simulation results with the experimental results from NASA’s Advanced Supersonic Parachute Research (ASPIRE) project. Through the validation, best practices for the modelling and simulation of supersonic PID are developed and proposed.

Rabinovitch, Jason↗
NASA NTRS2020

Combustion Studies of MMA/GOx for a Hybrid Rocket Motor

Poly(methyl methacrylate) (PMMA) is the synthetic polymer of methyl methacrylate (MMA), used in a multitude of applications, including as a solid fuel in hybrid rockets. PMMA undergoes pyrolysis into gaseous MMA (C5H8O2), which then undergoes combustion into carbon dioxide, water, carbon monoxide and low-molecular-weight compounds, including formaldehyde. Hybrid rocket motors as seen in the schematic in Fig. 1, contains the oxidizer in a pressurized tank, which is released through a port in the solid fuel grain in the combustion chamber, after which the combustion products are exhausted through a converging diverging nozzle.

Dhandapani, Chandru↗
NASA NTRS2019

Regolith Particle Erosion of Material in Aerospace Environments

This paper studies the effect of exposing thermal control S13GP:6N/LO-I white paint, Kapton flex cable, fiber optic cable, HEPA filter, and M55J graphite composite to high-velocity regolith environment that spacecraft landing on Mars are commonly exposed to. Due to the similarity between the Mars 2020 Rover design and Mars Science Laboratory design, it is expected that the Mars 2020 rover will be exposed to a similar high-speed regolith environment that the Mars Science Laboratory was exposed to. This environment is replicated to test the survivability of susceptible materials. The testing is performed at the University of Dayton Research Institute in Dayton, Ohio. The experiments expose different materials to basaltic–like particles ranging in size from approximately 40 μm to 2 cm, at velocities ranging from 19 m/s to 250 m/s, with varied particle fluxes (measured in mg/cm2). Depending on the size of the particle used, the particles can either embed in or erode the material. Posttest analysis shows that all materials tested will survive the expected environment observed during the Mars 2020 landing event. Some materials are tested to failure in order to better characterize material response. Materials that fail in some test scenarios include the paint, fiber optic cable, and the graphite composite. After being exposed to regolith, the α/ε ratio of the paint increased by ~37% due to particles embedding in the paint. Darkening of the paint can negatively affect thermal control of the rover. With high particle mass fluxes, the paint eventually degraded enough to expose the aluminum substrate. When impacted by a 1.5 cm particle traveling at 20 m/s, the fiber optic cable did not sever, but the impact did cause the cable to deform enough to crack the glass, which resulted in a significant increase in attenuation, rendering the cable unable to transmit data. The graphite composite also failed when exposed to high particle fluxes. All of the observed failures occurred for test cases above the expected landing environment with significant margin. Tests performed beyond the requirements help characterize how well these materials will survive in even more extreme environments for future missions.

Abid, Mohamed↗
NASA NTRS2019

SmallSat missions enabled by paired low-thrust hybrid rocket and low-power long-life Hall thruster

The capabilities of a SmallSat-class spacecraft targeting the outer solar system and using a combined chemical and electric propulsion system are explored. The development of compact hybrid rockets has enabled high-thrust engines to be packaged tightly enough to fit on cubesat and SmallSat spacecraft. These hybrid rockets provide 10’s-100 N of thrust depending on the propellant load & >300 s of specific impulse and have been demonstrated in both ambient and vacuum environments. Advancements in low-power long-life Hall thruster technologies have provided the potential for significantly greater propellant throughputs, enabling their use as a primary propulsion element on interplanetary spacecraft. In a recent characterization test campaign, the MaSMi-DM Hall thruster demonstrated power throttling from 150 – 1000 W with >1500 s of specific impulse available at >500 W and >40% total thrust efficiency available at >300 W; peak values of 1940 s and 53% were observed. A notional low-mass spacecraft employing a combined hybrid rocket and low-power electric propulsion system was designed and used for mission concept analysis targeting the outer solar system. Using an imposed wet mass limit of 400 kg, mission trajectories to Saturn and Uranus were generated. Orbit capture with >40% of the launch mass was shown to be possible at either target, with mission transfer times of 7.5 years and 13.5 years for Saturn and Uranus, respectively. Significant follow-on mission activities near Saturn (e.g. to Titan & Enceladus) were also possible by carrying extra propellant mass while remaining under the total wet mass limit.

Karp, Ashley C.↗