Engineering topics

Radovcich, N. A.

Publications and source records attributed to Radovcich, N. A..

9 records

NASA NTRS1989

Composite sizing and ply orientation for stiffness requirements using a large finite element structural model

A NASTRAN bulk dataset preprocessor was developed to facilitate the integration of filamentary composite laminate properties into composite structural resizing for stiffness requirements. The NASCOMP system generates delta stiffness and delta mass matrices for input to the flutter derivative program. The flutter baseline analysis, derivative calculations, and stiffness and mass matrix updates are controlled by engineer defined processes under an operating system called CBUS. A multi-layered design variable grid system permits high fidelity resizing without excessive computer cost. The NASCOMP system uses ply layup drawings for basic input. The aeroelastic resizing for stiffness capability was used during an actual design exercise.

Radovcich, N. A.↗

NASA NTRS1985

Integrated digital/electric aircraft concepts study

The integrated digital/electrical aircraft (IDEA) is an aircraft concept which employs all electric secondary power systems and advanced digital flight control systems. After trade analysis, preferred systems were applied to the baseline configuration. An additional configuration, the alternate IDEA, was also considered. For this concept the design ground rules were relaxed in order to quantify additional synergistic benefits. It was proposed that an IDEA configuration and technical risks associated with the IDEA systems concepts be defined and the research and development required activities to reduce these risks be identified. The selected subsystems include: power generation, power distribution, actuators, environmental control system and flight controls systems. When the aircraft was resized, block fuel was predicted to decrease by 11.3 percent, with 7.9 percent decrease in direct operating cost. The alternate IDEA shows a further 3.4 percent reduction in block fuel and 3.1 percent reduction in direct operating cost.

Cronin, M. J.↗

NASA NTRS1985

Study for the optimization of a transport aircraft wing for maximum fuel efficiency. Volume 1: Methodology, criteria, aeroelastic model definition and results

Work performed in the design of a transport aircraft wing for maximum fuel efficiency is documented with emphasis on design criteria, design methodology, and three design configurations. The design database includes complete finite element model description, sizing data, geometry data, loads data, and inertial data. A design process which satisfies the economics and practical aspects of a real design is illustrated. The cooperative study relationship between the contractor and NASA during the course of the contract is also discussed.

Radovcich, N. A.↗

NASA NTRS1984

Some experiences in aircraft aeroelastic design using Preliminary Aeroelastic Design of Structures (PAD)

The design experience associated with a benchmark aeroelastic design of an out of production transport aircraft is discussed. Current work being performed on a high aspect ratio wing design is reported. The Preliminary Aeroelastic Design of Structures (PADS) system is briefly summarized and some operational aspects of generating the design in an automated aeroelastic design environment are discussed.

Radovcich, N. A.↗

NASA NTRS1976

Study of flutter related computational procedures for minimum weight structural sizing of advanced aircraft

Results of a study of the development of flutter modules applicable to automated structural design of advanced aircraft configurations, such as a supersonic transport, are presented. Automated structural design is restricted to automated sizing of the elements of a given structural model. It includes a flutter optimization procedure; i.e., a procedure for arriving at a structure with minimum mass for satisfying flutter constraints. Methods of solving the flutter equation and computing the generalized aerodynamic force coefficients in the repetitive analysis environment of a flutter optimization procedure are studied, and recommended approaches are presented. Five approaches to flutter optimization are explained in detail and compared. An approach to flutter optimization incorporating some of the methods discussed is presented. Problems related to flutter optimization in a realistic design environment are discussed and an integrated approach to the entire flutter task is presented. Recommendations for further investigations are made. Results of numerical evaluations, applying the five methods of flutter optimization to the same design task, are presented.

Oconnell, R. F.↗

NASA NTRS1976

Derivatives of a statically reduced stiffness matrix with respect to sizing variables

An expression is obtained for the first derivatives with respect to the sizing variables of a statically reduced stiffness matrix that is a nonlinear function of the sizing variables, where the unreduced stiffness matrix is a linear function of the sizing variables. An accepted procedure to reduce the number of degrees of freedom is to eliminate a number of nodal displacements from the degrees of freedom such that the accuracy of the flutter analysis is not significantly affected. In a typical optimization procedure with flutter constraints, the derivative of the stiffness matrix may be used in a form that contains the characteristic vector of the flutter matrix equation and the transpose of the characteristic vector of the adjoint flutter matrix equation corresponding to a particular solution of the flutter equation.

Oconnell, R. F.↗

NASA NTRS1975

Study of flutter related computational procedures for minimum weight structural sizing of advanced aircraft, supplemental data

Computational aspects of (1) flutter optimization (minimization of structural mass subject to specified flutter requirements), (2) methods for solving the flutter equation, and (3) efficient methods for computing generalized aerodynamic force coefficients in the repetitive analysis environment of computer-aided structural design are discussed. Specific areas included: a two-dimensional Regula Falsi approach to solving the generalized flutter equation; method of incremented flutter analysis and its applications; the use of velocity potential influence coefficients in a five-matrix product formulation of the generalized aerodynamic force coefficients; options for computational operations required to generate generalized aerodynamic force coefficients; theoretical considerations related to optimization with one or more flutter constraints; and expressions for derivatives of flutter-related quantities with respect to design variables.

Oconnell, R. F.↗

NASA NTRS1975

Structural optimization with flutter speed constraints using maximized step size

A procedure is presented for the minimization of structural mass while satisfying flutter speed constraints. The procedure differs from other optimization methods in that the flutter speed is exactly satisfied at each resizing step, and the step size is determined by a direct minimization of the objective function (mass) for each set of flutter derivatives calculated. In conjunction with this method, a new move vector is suggested which results in a very efficient resizing procedure.

Oconnell, R. F.↗

NASA NTRS1975

Graphics Flutter Analysis Methods, an interactive computing system at Lockheed-California Company

An interactive computer graphics system, Graphics Flutter Analysis Methods (GFAM), was developed to complement FAMAS, a matrix-oriented batch computing system, and other computer programs in performing complex numerical calculations using a fully integrated data management system. GFAM has many of the matrix operation capabilities found in FAMAS, but on a smaller scale, and is utilized when the analysis requires a high degree of interaction between the engineer and computer, and schedule constraints exclude the use of batch entry programs. Applications of GFAM to a variety of preliminary design, development design, and project modification programs suggest that interactive flutter analysis using matrix representations is a feasible and cost effective computing tool.

Radovcich, N. A.↗