Search NASA⌕ Search

Engineering topics

Rahman, S.

Publications and source records attributed to Rahman, S..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Precision Determination of the Neutral Weak Form Factor of Ca 48

In this work, we report a precise measurement of the parity-violating asymmetry $A_{\rm PV}$ in the elastic scattering of longitudinally polarized electrons from $^{48}{\rm Ca}$. We measure $A_{\rm PV} =2668\pm 106\ {\rm (stat)}\pm 40\ {\rm (syst)}$ parts per billion, leading to an extraction of the neutral weak form factor $F_{\rm W} (q=0.8733$ fm$^{-1}) = 0.1304 \pm 0.0052 \ {\rm (stat)}\pm 0.0020\ {\rm (syst)}$ and the charge minus the weak form factor $F_{\rm ch} - F_{\rm W} = 0.0277\pm 0.0055$. The resulting neutron skin thickness $R_n-R_p=0.121 \pm 0.026\ {\rm (exp)} \pm 0.024\ {\rm (model)}$~fm is relatively thin yet consistent with many model calculations. The combined CREX and PREX results will have implications for future energy density functional calculations and on the density dependence of the symmetry energy of nuclear matter.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Accurate Determination of the Neutron Skin Thickness of Pb 208 through Parity-Violation in Electron Scattering

We report a precision measurement of the parity-violating asymmetry A PV in the elastic scattering of longitudinally polarized electrons from 208 Pb. We measure A PV = 550 ± 16 (stat) ±8 (syst) parts per billion, leading to an extraction of the neutral weak form factor F W (Q 2 = 0.00616 GeV 2 ) = 0.368 ± 0.013. Combined with our previous measurement, the extracted neutron skin thickness is R n -R p = 0.283 ± 0.071 fm. The result also yields the first significant direct measurement of the interior weak density of 208 Pb: ρ$^0_W$ = -0.0796 ± 0.0036(exp) ± 0.0013(theo) fm -3 leading to the interior baryon density ρ$^0_b$ = 0.1480 ± 0.0036(exp) ± 0.0013(theo) fm -3 . Finally, the measurement accurately constrains the density dependence of the symmetry energy of nuclear matter near saturation density, with implications for the size and composition of neutron stars.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2018

Study of light backgrounds from relativistic electrons in air light-guides

The MOLLER experiment proposed at the Thomas Jefferson National Accelerator Facility plans a precision low energy determination of the weak mixing angle via the measurement of the parity-violating asymmetry in the scattering of high energy longitudinally polarized electrons from electrons bound in a liquid hydrogen target (Moller scattering). A relative measure of the scattering rate is planned to be obtained by intercepting the Moller scattered electrons with a circular array of thin fused silica tiles attached to air light guides, which facilitate the transport of Cherenkov photons generated within the tiles to photomultiplier tubes (PMTs). The scattered flux will also pass through the light guides of downstream tiles, generating additional Cherenkov as well as scintillation light and is a potential background. In order to estimate the rate of these backgrounds, a gas-filled tube detector was designed and deployed in an electron beam at the MAMI facility at Johannes Gutenberg University, Mainz, Germany. Described in this paper is the design of a detector to measure separately the scintillation and Cherenkov responses of gas mixtures from relativistic electrons, the results of studies of several gas mixtures with comparisons to simulations, and conclusions about the implications for the design of the MOLLER detector apparatus.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2001

Engineering the Future of Full-Scale Propulsion Testing

Year 2000 has been an active one for rocket propulsion testing at the NASA John C. Stennis Space Center. This paper highlights several major test facilites for large-scale propulsion devices, and summarizes the varied nature of the recent test projects conducted at the Stennis Space Center (SSC) such as the X-33 Aerospike Engine, Ultra Low Cost Engine (ULCE) thrust chamber program, and the Hybrid Sounding Rocket (HYSR) program. Further, an overview of relevant engineering capabilities and technology challenges in conducting full-scale propulsion testing are outlined.

Ryan, H. M.↗
NASA NTRS2000

Current and Future Rocket Propulsion Testing at NASA Stennis Space Center

Year 2000 has been an active one for large-scale propulsion testing at the NASA John C. Stennis Space Center. This paper highlights several of the current-year test programs conducted at the Stennis Space Center (SSC) including the X-33 Aerospike Engine, Ultra Low Cost Engine (ULCE) program, and the Hybrid Sounding Rocket (HYSR) program. Future directions in propulsion test are also introduced including the development of a large-scale Rocket Based Combined Cycle (RBCC) test facility.

Ryan, H. M.↗
NASA NTRS1999

Overview of Rocket Propulsion Testing at NASA Stennis Space Center

THe recent nationwide thrust toward development of low-cost space transportation has precipitated a sharp increase in demand for subscale and full-scale propulsion test services. This paper highlights the unique capabilities of Stennis Space Center(SSC) to meet these demands, and summarizes several major propulsion test activities and other related milestone achievements during the 1999 calendar year. The current and projected list of SSC test projects heralds an even more vigorous, interesting, and challenging future in propulsion test.

Rahman, S.↗
NASA NTRS1986

Distribution system simulator

In a series of tests performed under the Department of Energy auspices, power line carrier propagation was observed to be anomalous under certain circumstances. To investigate the cause, a distribution system simulator was constructed. The simulator was a physical simulator that accurately represented the distribution system from below power frequency to above 50 kHz. Effects such as phase-to-phase coupling and skin effect were modeled. Construction details of the simulator, and experimental results from its use are presented.

Bahrami, K. A.↗
NASA NTRS1982

Computer simulations of optimum boost and buck-boost converters

The development of mathematicl models suitable for minimum weight boost and buck-boost converter designs are presented. The facility of an augumented Lagrangian (ALAG) multiplier-based nonlinear programming technique is demonstrated for minimum weight design optimizations of boost and buck-boost power converters. ALAG-based computer simulation results for those two minimum weight designs are discussed. Certain important features of ALAG are presented in the framework of a comprehensive design example for boost and buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight annd loss profiles of various semiconductor components and magnetics as a function of the switching frequency.

Rahman, S.↗
NASA NTRS1981

A new approach to the minimum weight/loss design of switching power converters

A new technique using the mathematical nonlinear programming ALAG is proposed to facilitate design optimizations of switching power converters. This computer-aided approach provides a minimum weight (or loss) design down to the details of component level and concurrently satisfies all related power-circuit performance requirements. It also provides such design insights as tradeoffs between power loss and system weight as the switching frequency is increased.

Lee, F. C.↗
NASA NTRS1981

Nonlinear program based optimization of boost and buck-boost converter designs

The facility of an Augmented Lagrangian (ALAG) multiplier based nonlinear programming technique is demonstrated for minimum-weight design optimizations of boost and buck-boost power converters. Certain important features of ALAG are presented in the framework of a comprehensive design example for buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.

Rahman, S.↗
NASA NTRS1980

Modeling and Analysis of Power Processing Systems (MAPPS). Volume 1: Technical report

Computer aided design and analysis techniques were applied to power processing equipment. Topics covered include: (1) discrete time domain analysis of switching regulators for performance analysis; (2) design optimization of power converters using augmented Lagrangian penalty function technique; (3) investigation of current-injected multiloop controlled switching regulators; and (4) application of optimization for Navy VSTOL energy power system. The generation of the mathematical models and the development and application of computer aided design techniques to solve the different mathematical models are discussed. Recommendations are made for future work that would enhance the application of the computer aided design techniques for power processing systems.

Lee, F. C.↗