Search NASA⌕ Search

Engineering topics

Raman, Roger

Publications and source records attributed to Raman, Roger.

$\mathrm{T}$ransient $\mathrm{CHI}$ System Design Studies for $\mathrm{P}$ EGASUS -$\mathrm{III}$

We report transient coaxial helicity injection (transient CHI), first developed on the Helicity Injected Torus-II (HIT-II) and later on the National Spherical Torus Experiment (NSTX) for implementing solenoid-free plasma current startup capability in a spherical tokamak (ST), is now planned to be tested on the Pegasus-III ST using a novel double-biased configuration. Such a configuration is likely needed for transient CHI deployment in a reactor. The transient CHI system optimization will be studied on Pegasus-III to enable startup toroidal persisting currents at the limits permitted by the external poloidal field coils. A transient CHI discharge is generated by driving injector current along magnetic field lines that connect the inner and outer divertor plates on one end of the ST. Simulations using the Tokamak Simulation Code are used to assess the transient CHI toroidal current generation potential and electrode gap location on the Pegasus-III. While past transient CHI systems have used high-voltage, oil-filled capacitors for driving the injector current, for improved safety, Pegasus-III will use a high-current capacitor bank based on low-voltage electrolytic capacitors. The designed and fabricated system is capable of over 32 kA. The modular design features permit the system to be upgraded to higher currents, as needed, to meet the future needs of the Pegasus-III facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NSTX-U theory, modeling and analysis results

Here, the mission of the low aspect ratio spherical tokamak NSTX-U is to advance the physics basis and technical solutions required for optimizing the configuration of next-step steady-state tokamak fusion devices. NSTX-U will ultimately operate at up to 2 MA of plasma current and 1 T toroidal field on axis for 5 s, and has available up to 15 MW of neutral beam injection power at different tangency radii and 6 MW of high harmonic fast wave heating. With these capabilities NSTX-U will develop the physics understanding and control tools to ramp-up and sustain high performance fully non-inductive plasmas with large bootstrap fraction and enhanced confinement enabled via the low aspect ratio, high beta configuration. With its unique capabilities, NSTX-U research also supports ITER and other critical fusion development needs. Super-Alfvénic ions in beam-heated NSTX-U plasmas access energetic particle (EP) parameter space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. NSTX-U can also generate very large target heat fluxes to test conventional and innovative plasma exhaust and plasma facing component solutions. This paper summarizes recent analysis, theory and modelling progress to advance the tokamak physics basis in the areas of macrostability and 3D fields, EP stability and fast ion transport, thermal transport and pedestal structure, boundary and plasma material interaction, RF heating, scenario optimization and real-time control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Initial Results from High-Field-Side Transient CHI Start-Up on QUEST

Transient coaxial helicity injection (t-CHI) current start-up using a new design simple electrode configuration has been implemented on the QUEST. Discharges injected from the low field side (LFS) and from the high field side (HFS) were examined. Compared to the LFS injection case, the HFS injection has the advantages of providing access to a higher toroidal field and better controlling the location of the injector flux footprint location. Although the present PF coils on QUEST are not well positioned to form the injector flux on the HFS injector region and there has been a frequent occurrence of the spurious arcs, known as absorber arcs, HFS injection has shown flux evolution in a shape that is suitable for the formation of closed flux surfaces. The discharges were improved by installing an in-vessel-coil and adding a new cylindrical electrode to the existing CHI electrode. Overall, the results show that the new cylindrical electrode allowed the flux to evolve stably while allowing both the inner and the outer injector flux footprint to remain in the vicinity of the cylindrical electrode. This configuration which inherently generates a narrow injector flux footprint width resulted in discharges that strongly suggested the persistence of the CHI generated plasma after the injector current was reduced to zero. These studies have informed us of the need to improve the CHI gas injection system so that the absorber arcs could be better controlled in the HFS injection configuration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modelling of Ablatant Deposition from Electromagnetically Driven Radiative Pellets for Disruption Mitigation Studies

The Electromagnetic Particle Injector (EPI) concept is advanced through the simulation of ablatant deposition into ITER H-mode discharges with calculations showing penetration past the H-mode pedestal for a range of injection velocities and granule sizes concurrent with the requirements of disruption mitigation. As discharge stored energy increases in future fusion devices such as ITER, control and handling of disruption events becomes a critical issue. An unmitigated disruption could lead to failure of the plasma facing components resulting in financially and politically costly repairs. Methods to facilitate the quench of an unstable high current discharge are required. With the onset warning time for some ITER disruption events estimated to be less than 10 ms, a disruption mitigation system needs to be considered which operates at injection speeds greater than gaseous sound speeds. Such an actuator could then serve as a means to augment presently planned pneumatic injection systems. The EPI uses a rail gun concept whereby a radiative payload is delivered into the discharge by means of the JxB forces generated by an external current pulse, allowing for injection velocities in excess of 1 km/s. The present status of the EPI project is outlined, including the addition of boost magnetic coils. These coils augment the self-generated rail gun magnetic field and thus provide a more efficient acceleration of the payload. The coils and the holder designed to constrain them have been modelled with the ANSYS code to ensure structural integrity through the range of operational coil cu

disruption↗

CHI Research. Final Technical Report

The spherical tokamak is a leading candidate for a Fusion Nuclear Science Facility (FNSF) due to its compact size and modular configuration. It is highly desirable for the FNSF to be compact in size and simpler in configuration. Since the central solenoid cannot be used for driving current during the steady-state phase, the tokamak design would also be simplified if it could be built without the solenoid, and it would allow access to lower aspect ratio configurations. Great progress has been made in developing Transient CHI as a viable solenoid-free plasma start-up method. These are: (a) The generation of closed flux current in HIT-II and NSTX, and the successful coupling of this current to induction from the central solenoid, (b) the generation of 0.1 MA closed flux current in HIT-II and demonstration of CHI plasma quality similar to that produced inductively, (c) the generation of a record 0.2 MA of closed flux current in NSTX and the coupling of the CHI-produced discharge in NSTX to induction with subsequent transitioning to a high-performance H-mode discharge when neutral beams were injected and (e) CHI-started discharges to which induction has been applied have ramped-up to 1 MA in NSTX with record low flux consumption. Modeling of the CHI process using TSC and NIMROD has led to a much-improved understanding of the physics of magnetic reconnection leading to large volume flux closure. The NIMROD results indicate that this reconnection mechanism scales to arbitrarily high toroidal field and can be either axisymmetric Sweet-Parker like reconnection or it can be enhanced through plasmoid formation. Motivated by the exciting experimental and modeling results from HIT-II and NSTX, we explored the application of CHI to a reactor configuration, and identified methods for enabling CHI capability in a FNSF-sized experiment. In the first, proven, concept referred to as "NSTX-like", the entire blanket structure is insulated from the vessel using insulating supports. In the second configuration referred to as "DIII-D - like", a toroidal insulated electrode is placed on top of the blanket structure to shield the insulator from neutrons, allowing more than six years of full power operations before insulator replacement. The second concept requires an experimental test for concept validation. To test this second concept, during the period of 2013 to 2016, we designed and implemented a new simpler design CHI configuration on QUEST. Initial TSC modeling and experimental results suggests that work on QUEST may lead to a simpler Transient CHI configuration for a ST-FNSF. Transient CHI is now also in the process of being implemented on the PEGASUS ST at the University of Washington to study very high-current start-up potential of transient CHI.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

JRT (Joint Research Target) 2016 4th Quarter Report and Final Summary

This report summarizes the work completed during the final quarter of FY2016 on the three major US tokamak facilities as part of this past year’s joint research target. Following this summary section are detailed reports from the three facilities. We begin by requoting the overarching JRT goals, including the particulars for the 4 th quarter milestones.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Large-volume flux closure during plasmoid-mediated reconnection in coaxial helicity injection

A large-volume flux closure during transient coaxial helicity injection (CHI) in NSTX-U is demonstrated through resistive magnetohydrodynamics (MHD) simulations. Several major improvements, including the improved positioning of the divertor poloidal field coils, are projected to improve the CHI start-up phase in NSTX-U. Simulations in the NSTX-U configuration with constant in time coil currents show that with strong flux shaping the injected open field lines (injector flux) rapidly reconnect and form large volume of closed flux surfaces. This is achieved by driving parallel current in the injector flux coil and oppositely directed currents in the flux shaping coils to form a narrow injector flux footprint and push the injector flux into the vessel. As the helicity and plasma are injected into the device, the oppositely directed field lines in the injector region are forced to reconnect through a local Sweet–Parker type reconnection, or to spontaneously reconnect when the elongated current sheet becomes MHD unstable to form plasmoids. In these simulations for the first time, it is found that the closed flux is over 70% of the initial injector flux used to initiate the discharge. These results could work well for the application of transient CHI in devices that employ super conducting coils to generate and sustain the plasma equilibrium.

Current Drive↗

Evaporated lithium surface coatings in NSTX

Two lithium evaporators were used to evaporate more than 100 g of lithium on to the NSTX lower divertor region. Prior to each discharge, the evaporators were withdrawn behind shutters, where they also remained during the subsequent HeGDC applied for periods up to 9.5 min. After the HeGDC, the shutters were opened and the LITERs were reinserted to deposit lithium on the lower divertor target for 10 min, at rates of 10–70 mg/min, prior to the next discharge. Overall, the major improvements in plasma performance from these lithium depositions include: (1) plasma density reduction as a result of lithium deposition; (2) suppression of ELMs; (3) improvement of energy confinement in a low-triangularity shape; (4) improvement in plasma performance for standard, high-triangularity discharges; (5) reduction of the required HeGDC time between discharges; (6) increased pedestal electron and ion temperature; (7) reduced SOL plasma density; and (8) reduced edge neutral density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗