Hydrodynamic Instabilities in High-Speed Droplet Breakup
Explore the source record for details and available documents.
Physics↗
Engineering topics
Ramaprabhu, Praveen
Publications and source records attributed to Ramaprabhu, Praveen.
Simulations and models for the Richtmyer– Meshkov instability with broadband perturbations
The Richtmyer–Meshkov instability (RMI) is shock driven and affects many phenomena from inertial fusion to supernova explosions. The behavior of single-modes in the RMI has been studied extensively but less is known with the broadband perturbations that occur in applications. Here, we describe extensive numerical simulations and modeling of the RMI with broadband perturbations with an initial power spectrum of the form P∝ k m , where k is the wavenumber. The hydrodynamic condition is the same as in the $\theta$-Group Collaboration [Thornber et al., “Late-time growth rate, mixing, and anisotropy in the multimode narrowband Richtmyer–Meshkov instability: The $\theta$-group collaboration,” Phys. Fluids 29, 105107 (2017)] with a Mach ~1.86 shock and gamma-law = 5/3 fluids with Atwood number A = 0.5. The bubble amplitude h B is found to grow in two stages. Initially, h B undergoes a phase-inversion and grows linearly in time (t) at a rate consistent with a linear theory. Asymptotically, h B grows as a power law $~t^{\theta}$ when $\langle{k}\rangle{|h_B|}$ > O(1), where $\langle{k}\rangle$ is the average wavenumber for the initial spectrum. The RMI behavior in simulations and modeling agree over a wide range of exponent m, spectral width, initial amplitude, and time. The agreement is quantified objectively using statistical analysis.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Local wave-number model for inhomogeneous two-fluid mixing
We analyze the local wave-number (LWN) model, a two-point spectral closure model for turbulence, as applied to the Rayleigh-Taylor (RT) instability, the flow induced by the relaxation of a statically-unstable density stratification. Model outcomes are validated against data from 3D simulations of the RT instability. In the first part of the study we consider the minimal model terms required to capture inhomogeneous mixing and show that this version, with suitable model coefficients, is sufficient to capture the evolution of important mean global quantities including mix-width, turbulent mass flux velocity, and Reynolds stress, if the start time is chosen such that the earliest transitions are avoided. However, this simple model does not permit the expected finite asymptote of the density-specific-volume covariance b. In the second part of the study, we investigate two forms for a source term for the evolution of the spectrum of density-specific-volume covariance for the LWN model. The first includes an empirically motivated calibration of the source to achieve the final asymptotic state of constant b. Here, the second form does not require calibration but, in conjunction with enhanced diffusion and drag captures the full evolution of all the dynamical quantities, namely, the mix-layer growth, turbulent mass-flux velocity, Reynolds stress, as well as the desired behavior of b.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Rayleigh–Taylor and Richtmyer–Meshkov instabilities: A journey through scales
Hydrodynamic instabilities such as Rayleigh–Taylor (RT) and Richtmyer–Meshkov (RM) instabilities usually appear in conjunction with the Kelvin–Helmholtz (KH) instability and are found in many natural phenomena and engineering applications. They frequently result in turbulent mixing, which has a major impact on the overall flow development and other effective material properties. This can either be a desired outcome, an unwelcome side effect, or just an unavoidable consequence, but must in all cases be characterized in any model. The RT instability occurs at an interface between different fluids, when the light fluid is accelerated into the heavy. The RM instability may be considered a special case of the RT instability, when the acceleration provided is impulsive in nature such as that resulting from a shock wave. Here in this pedagogical review, we provide an extensive survey of the applications and examples where such instabilities play a central role. First, fundamental aspects of the instabilities are reviewed including the underlying flow physics at different stages of development, followed by an overview of analytical models describing the linear, nonlinear and fully turbulent stages. RT and RM instabilities pose special challenges to numerical modeling, due to the requirement that the sharp interface separating the fluids be captured with fidelity. These challenges are discussed at length here, followed by a summary of the significant progress in recent years in addressing them. Examples of the pivotal roles played by the instabilities in applications are given in the context of solar prominences, ionospheric flows in space, supernovae, inertial fusion and pulsed-power experiments, pulsed detonation engines and Scramjets. Progress in our understanding of special cases of RT/RM instabilities is reviewed, including the effects of material strength, chemical reactions, magnetic fields, as well as the roles the instabilities play in ejecta formation and transport, and explosively expanding flows. The article is addressed to a broad audience, but with particular attention to graduate students and researchers who are interested in the state-of-the-art in our understanding of the instabilities and the unique issues they present in the applications in which they are prominent.
42 ENGINEERING↗
Special Issue: To Commemorate the Legacy of Malcolm J. Andrews—Scientist, Educator, and Leader
This special issue celebrates the scientific legacy of Dr. Malcolm J. Andrews, former Editor of the ASME Journal of Fluids Engineering (2010–2018). Malcolm devoted his career to the development and applications of computational, experimental, and analytical tools to investigate and solve diverse, complex fluid dynamics, and heat transfer problems. Malcolm’s most notable research accomplishments include: (i) contributions to innovative experiments, simulations, and theory to understand buoyancydriven turbulent mixing due to Rayleigh–Taylor instability; (ii) development of the multiphase particle-in-cell method for understanding fragmentation in spray jets, coal-water slurry, and other dense particulate flows; (iii) mixing in nano- and biomaterials in applications ranging from protein glues to carbon nanotube composites; (iv) determining dispersion in proteins to improve therapeutic drug delivery via micro-encapsulation; (v) innovative methods for storing information using nanopinned dipole magnetic vortices in superconducting materials; and (vi) modeling and design modifications for shell-and-tube heat exchangers, as well as heat transfer in rotating systems such as turbine blades. The results of his research have been published in a long series of trend-setting journal and conference papers, book chapters, and patents.
42 ENGINEERING↗