Engineering topics

Ramos, Jose L.

Publications and source records attributed to Ramos, Jose L..

14 records

DOE OSTI2024

Polymer-fiber-reinforced polymers with enhanced interfacial bonding between polypropylene fiber and polyethylene matrix

Self-reinforced composites (SRCs) consist of reinforcing fibers and a base matrix made of the same thermoplastic polymer, offering lightweight, recyclability, and sustainability benefits. However, limited research exists on composites where the reinforcing thermoplastic polymer fibers differ from the base thermoplastic matrix. Here, this study focuses on investigating the mechanical behavior of such composites and exploring different surface modification methods to enhance the fiber/matrix interfacial bonding using polypropylene fibers and a polyethylene matrix as an example. It is shown that surface treatment with a commercial adhesion promoter containing n-butyl acetate significantly improves the interfacial shear strength between polypropylene fibers and the polyethylene matrix, increasing it by 145% compared to other methods investigated. Additionally, increasing the length of the embedded polymer fiber in the matrix leads to a notable increase in specific interfacial energy. Consequently, the thermoplastic polymer-fiber-reinforced polymers (PFRPs) using surface-treated woven polypropylene fabrics and a polyethylene matrix exhibit a 20% higher tensile strength and a 65% higher toughness compared to non-treated PFRPs. This study also shows that specific mechanical properties (normalized by the composite density) of the investigated woven PFRPs are similar to those of non-treated SRCs under uni-axial tension. Particularly, their ductility outperforms carbon-/glass-/aramid-fiber-reinforced polymers by at least 6 times at a same fiber volume fraction. The investigation of such composites and the exploration of surface modification methods present important progress in the field of thermoplastic PFRPs, which serve as a solution for addressing concerns related to recyclability and sustainability.

Fiber pull-out↗

DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Equivalent Properties of Interfacial Void Defects at the CFRTP-adhesive Interface and Their Detrimental Effects on the Bonding Performance of Metal-CFRTP Dissimilar Joints

This paper revealed the detrimental effects of micro-scale air interfacial voids on the debonding at the interface of carbon-fiber-reinforced polyphthalamide (CFRPPA) and thermoset adhesive, representing a weak adherend-adhesive interface, within a dissimilar joint made of an aluminum alloy and a CFRPPA. The reduced lap shear strength of the joint, due to different void area fractions at the CFRPPA-adhesive interface, can be computationally described by using equivalent interfacial properties in the modeling to avoid the explicit modeling of the micro-scale interfacial voids. Such equivalent interfacial properties (e.g., interfacial normal strength, etc.) was found to have a non-linear relationship with respect to interfacial void area fraction as well as lap shear strength. This work has practical applications by utilizing equivalent interfacial properties for the analytical and/or computational design(s) of adhesively bonded joints.

Qiao, Yao↗

DOE OSTI2024

An in-situ view cell system for investigating swelling behavior of elastomers upon high-pressure hydrogen exposure

The transition to hydrogen as a clean and efficient energy carrier is impeded by challenges in the compatibility of hydrogen with materials used within hydrogen infrastructure. Elastomers, crucial in sealing components, often exhibit premature failures in high-pressure hydrogen environments due to excessive swelling. This study employs an innovative in-situ view cell system to assess the swelling behavior of hydrogenated nitrile butadiene rubber (HNBR) under various hydrogen conditions. The system, designed to withstand pressures up to 96.5 MPa, incorporates Digital Image Correlation (DIC) for strain measurements and volume estimation. Results reveal non-linear volume increases during depressurization, challenging conventional assumptions. Furthermore, investigations into peak hydrogen pressures and pressure-holding scenarios during decompression highlight complex swelling trends. The introduction of a novel computer vision (CV) method enhances precision in volume estimation, overcoming DIC limitations. The study provides insights into mitigating elastomer swelling, crucial for developing robust materials to support future hydrogen-driven energy systems.

Elastomer↗

DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Low-velocity repeated impact behaviors of Polymer Fiber Reinforced Plastics (PFRPs)

Modern fiber-reinforced composites have become ubiquitous across multiple industries due to their excellent weight-to-strength ratio. Typically glass or carbon fibers are widely used. While Glass or Carbon Fiber-Reinforced Plastics (GFPRs or CFPRs) have good stiffness, strength, and fatigue life, they are expensive and difficult to recycle. Researchers are exploring Polymer Fiber-Reinforced Plastics (PFRPs) as an alternative solution. PFRPs utilize polymer fibers and a polymer matrix. A wide range of materials options is available, including low-cost thermoplastics such as polyethylene or polypropylene. These thermoplastics are easy to handle and recyclable without special methods. Manufacturing parts using thermoplastics are well-established as well. However, their mechanical performances have not been extensively studied compared to GFRPs or CFRPs. This study examines the low-velocity impact resistance of PFRPs made of different thermoplastics. The low-velocity impacts are applied through a drop-weight tower. The experiment is divided into two cases: a single perforation impact and low-energy repeated impacts. Energy absorption and the number of impacts to failure are measured. The results are compared to traditional CFRPs which have a thermoset matrix. The PFRPs demonstrate energy absorption capabilities comparable to or greater than those of CFRPs with respect to specimen thickness and density. Additionally, the PFRPs show significantly higher impacts-to-failure than the CFRPs in low-energy repeated impact tests. This is particularly noteworthy considering that the PFRPs are much simpler and more economical to manufacture than CFRPs. To further

Ko, Seunghyun↗

DOE OSTI2023

Processing Temperature Effect on Failure Behavior of Unidirectional Thermoplastic Polymer-fiber-reinforced Polymers (PFRPs)

This study aimed to examine the influence of processing temperature on the mechanical and morphological characteristics of unidirectional (UD) thermoplastic polymer-fiber-reinforced polymers (PFRPs), utilizing UHMWPE-polymer-fiber-reinforced HDPE composites as an example. To achieve this objective, UD thermoplastic PFRPs were produced through filament winding and hot pressing techniques, employing five distinct processing temperatures within the range spanning from the melting onset temperature of the polymer matrix to the melting peak temperature of the reinforcing polymer fiber. By conducting the uni-axial tensile tests on the UD UHMWPE-polymer-fiber-reinforced HDPE composites fabricated at different processing temperatures, it was shown that the optimal longitudinal tensile properties of the composites, comparable with glass-fiber-reinforced thermoset or thermoplastic polymers (GFRPs or GFRTPs) can be achieved when the processing temperature does not significantly exceeds the melting onset temperature of the reinforcing polymer fiber. However, when the processing temperature exceeds this threshold, the mechanical properties of the composites are significantly reduced, as evidenced by the transition in the failure morphology from the presence of significant splitting cracks to the occurrence of plastic necking due to the complete melting of the reinforcing polymer fibers in a composite. Particularly, the ductile behavior of the optimal thermoplastic PFRPs investigated in this study is superior than that of carbon-fiber-reinforced thermoset or thermoplastic polymers (CFRPs or CFRTPs) and even GFRPs and GFRTPs. This study not only provides valuable insights into the proper fabrication of high-performance thermoplastic PFRPs but also offers useful experimental data that can aid in the validation and development of computational models, particularly those related to processing modeling.

Qiao, Yao↗

DOE OSTI2023

A Micro-scale Numerical Investigation of Internal and Interfacial Void Defects in Adhesive on Failure Behavior of Adhesively-Bonded Materials with Rough Surfaces

This paper studied the effects of air void defects on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicated that interfacial void defects can largely facilitate interfacial debonding of a weaker adherend/adhesive interface under shear. However, this is not the case for a stronger adherend/adhesive interface, showing the reduction on the nominal shear strength of an adhesive joint is mainly due to internal void defects. The reduced bonding performance due to voids can be improved by leveraging an appropriate surface roughness. This preliminary investigation is a first step to better understand the micro-mechanics of interfacial failure in the adhesion of a roughened/patterned adherend via surface modification(s) and an adhesive, and also shows the importance of minimizing interfacial void defects in particular at a weaker adherend/adhesive interface via different techniques.

Qiao, Yao↗

DOE OSTI2023

A study of adhesive bonding in metal–metal, metal–CFRP, and CFRP–CFRP material combinations under shear deformation: Fracture morphologies and damage mechanisms

Safe design of adhesive joining in multi-materials in engineered structures requires the accumulation of numerous experimental data on the failure behavior of various adhesively-bonded material combinations under different loading conditions. The deep understanding of mechanical performance, fracturing morphologies, and main damage mechanisms is also quintessential for accelerating the development of proper physics-based and multi-scale models for assisting the design. Towards this goal, this work presents a comprehensive characterization of the failure behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP material combinations under global shear deformation via single lap shear testing. Thanks to a synergistic combination of measurement methods by using Digital Imaging Correlation (DIC) and 3D optical profilometry, adhesive features on the adherend after failure were quantified and the main progressive damage mechanisms were identified. The characterization performed in this work provides quantitative data that contributes to a better understanding of shear failure in adhesive bonding across different bi-material combinations. Finally, the obtained results have practical implications, including the potential to enhance adhesive bonding design, identify failure causes in adhesive joints, and develop or validate computational models capable of capturing the observed behavior in various adhesively-bonded materials under global shear deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Shear Assisted Processing and Extrusion (ShAPE) of Plastics: Recycling and Remolding

Polyethylene (PE) and polypropylene (PP) are often disposed as mixed plastic wastes. The challenges in recycling and upcycling these mixed polyolefin wastes lie in the difficulty in separating individual constituents in a cost-effective and scalable manner. Direct recycling the mixed PE and PP wastes in conventional melt-phase extruders typically result in a product with poor properties and low added value, because of immiscibility, phase separation, and lack of crystallinity. Friction extrusion (FE), a solid phase processing technique that has successfully extruded metal matrix composites with desired end products, has never been utilized to address the issue of recycling mixed plastic wastes. In this study, FE was performed on single-stream low-density polyethylene (LDPE), single-stream PP and mixed-stream LDPE+PP. Consolidated filaments of 2.5 mm diameter were extruded from different precursors. The thermal, infrared, and microscopic properties of extruded filaments were measured to evaluate the effects of FE process on the structure of recycled polymers. Meanwhile, the energy efficiency of FE was estimated based on extrusion rates and compared with conventional melt extrusion processes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Interfacial bond characterization of epoxy adhesives to aluminum alloy and carbon fiber-reinforced polyamide by vibrational spectroscopy

Vibrational spectroscopic technique has been utilized to investigate interfacial bonding chemistry of two epoxy adhesive products, XP0012 and XP5005F, on plasma-treated AA6061 and carbon fiber-reinforced polyamide 66 (CFRP-PA66) surfaces. The change in vibrational peak ratios was measured by attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy to deduce bonding mechanisms. Both adhesives showed strong crosslinking polymerization of hydroxyl- and amine-initiated epoxy ring opening on AA6061 surface, but on CFRP surface XP0012 formed a simple amide linkage by the reaction of surface hydroxyl groups and nitrile groups of curing agent, and XP5005F formed a crosslinked network by hydroxyl-initiated epoxy ring opening polymerization. The different interfacial bonding formation of two adhesives on CFRP-PA66 surface is attributed to additive effect. Addition of additives to epoxy adhesives (XP5005F) changed the interfacial bonding mechanism on CFRP-PA66 surface, rather forming hydroxyl-initiated epoxy opening crosslinking polymerization than a simple amide bond formation (XP0012). The interfacial bonding chemistry was also proved by addition of bisphenol A (BA) to a simplified model diglycidyl ether of bisphenol A/dicyandiamide (DGEBA/DICY) epoxy system. When BA was added to the model DGEBA/DICY system, epoxy ring gradually decreased on CFRP-PA66 surface, while without BA, DGEBA/DICY showed only decrease in a nitrile peak intensity in ATR-FTIR. In conclusion, the foregoing different types of interfacial chemical bonds at the adhesive/CFRP-PA66 interfaces can affect the lap shear behavior of the joint.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Low-Velocity Impact Performances of Healed Polymer Fiber Reinforced Plastics

Extending the lifecycle of traditional carbon or glass fiber-reinforced plastics is a complicated problem. The lack of sustainability limits the applications of the traditional composite materials in the vehicle industries where recycling and repurposing are critical issues. Alternatives for the low-stressed structural components are polymer fiber-reinforced plastics (PFRPs). In PFRPs, both the fibers and matrix are composed of thermoplastic polymers (e.g. polypropylene or polyethylene). They are lightweight, easy to manufacture, and cost-effective. Additionally, recycling and repurposing thermoplastic polymers are well understood. Therefore, the PFRPs have strong advantages compared to the traditional fiber-reinforced composites in low-stressed structural applications. In this study, we investigated the low-velocity impact (LVI) performances of the PFRPs and compared them with carbon fiber-reinforced plastics (CFRPs). A semi-spherical impactor was dropped to flat, square panels, and the absorbed impact energy was measured. The damage mechanisms were examined using a Xray µCT scan. The PFRPs outperformed the CFRPs in terms of perforation energy normalized by plate thickness and density. After the perforation, we healed the fractured plates by leveraging the recyclability of the thermoplastic polymers. The healing process of the panels was identical to the initial panel manufacturing process. No additional materials were added during the healing process. The healed PFRP panels were impacted again and substantially recovered energy absorption capability. We also conducted the repeated-impact test with several different impact energies. Unlike the CFRPs where the impact peak load decreased as the impacts repeated, the PFRPs showed an increasing trend. Such a unique mechanism was due to the strain-hardening behavior of the polymer fibers and matrix. As a result, the repeated-impact life of the PFRPs was significantly enhanced. These results are particularly interesting in the automotive or aerospace industries where repeated LVI is frequently observed.

Ko, Seunghyun↗

DOE OSTI2022

Plasma surface modification coupled with thermal and step-over distance effects on significant fracture improvement of adhesively-bonded metal-$\mathrm{CFRTP}$ dissimilar materials

Here, this work proposes an approach to improve the interfacial bonding between carbon-fiber-reinforced thermoplastic polymers (CFRTP) and thermoset adhesive by using the surface modification with the combination of air plasma, thermal, and step-over effects. Thanks to the proper heating which causes the exposure of carbon fibers on the CFRTP surface, both polymer matrix and these exposed carbon fibers can have improved bonding with adhesive due to air plasma treatment. By conducting the Double Cantilever Beam (DCB) tests performed on adhesively-bonded AA5052/CFRP-PA66 dissimilar joints, it was shown in this work that the average Mode I specific fracture energy can be improved up to about 180% compared to non-treated counterparts. The foregoing improvement can be further increased by considering the step-over distance of the surface treatment, which triggers the tortuous damage path in the failure process of adhesively-bonded structures. By manipulating this treatment parameter, often overlooked in the literature, and other parameters (i.e., treatment speed, nozzle tip-to-surface distance, etc.) investigated in this study, the average Mode I specific fracture energy of adhesively-bonded AA5052/CFRP-PA66 dissimilar joints can be improved reaching up to about 410% compared to non-treatment counterparts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

The Roles of Interface, Adherend, and Adhesive in Plasma- and Other-treated Joints of Metals and FRP Materials Under Shear Deformation

This work investigated the role of interface, adherend, and adhesive in adhesively-bonded metal-metal, metal-CFRTP, and CFRTP-CFRTP combinations with plasma-treated surfaces under shear deformation. To this end, aluminum alloys (AA5052 and AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) were used as examples and performed through single lap shear testing. The results showed that air plasma surface treatment can improve the shear behavior of adhesively-bonded AA5052-CFRPA66 and CFRPA66-CFRPA66 joints with about 20% enhanced lap shear strength compared to non-treated cases. Failure surface morphology of plasma-treated CFRPA66 adherend confirmed this improvement by showing an increased amount of adhesive failure than interfacial failure between CFRPA66 and adhesive. But this is not true for AA5052-AA6061 joints with plasma-treated surfaces exhibiting almost no enhanced lap shear strength. This study also showed the importance of selecting a proper surface modification method for the enhancement of adhesive-bonded structures under shear deformation through the analysis of the results in this study and in the literature. For fiber-reinforced polymers (FRPs), improving FRP/adhesive interface may be prioritized via different surface modification methods (e.g., plasma, chemical coating, etc.) than adhesive modification methods. However, for surface-cleaned metals, toughening adhesive via different enhancement methods (e.g., nano-particles, chemical enhancement, etc.) may be more important than improving metal/adhesive interface. These insightful results are valuable in the area of multi-materials joining.

Qiao, Yao↗