Exploring irradiated granular flows with rapid heating for concentrated solar thermal energy collection and storage
Not Available
Jeong, Shin Young (ORCID:0000000347897129)↗
Engineering topics
Ranjan, Devesh
Publications and source records attributed to Ranjan, Devesh.
Discoveries in Blast-Driven Turbulence of Astrophysical Relevance
The fluid mixing caused by variable-density instabilities is important in a wide variety of scenarios from ocean mixing and astrophysical phenomena to nuclear fusion techniques and atomic weapons. This thesis explores the mixing resulting from a specific instability known as the Blast Driven Instability (BDI). This work investigates the variable density mixing in an explosively driven environment due to the fluid instabilities at the material interfaces. Specifically, diverging Richtmyer-Meshkov (impulsive-acceleration environment) and Rayleigh-Taylor (variable-acceleration environment) instabilities (present in supernova and inertial confinement fusion) are studied using advanced high-speed diagnostics in carefully designed laboratory experiments. The BDI morphology is presented through a time development of Mie scattering images, and steps through the parameter space (varying density ratio and driver speed), highlighting the development of the structures that form during mixing. A scaling criterion is used to relate the two systems of vastly different spatiotemporal scales. Velocity fields in the BDI have been captured for the first time using the high temporal resolution PIV technique. Subsequent analysis of the dynamics of the instability from the velocity fields illustrates the distribution of kinetic energy, the transition to turbulence, and the characteristic growth of the instability are discussed. This study furthers understanding of how blast-driven instability pertains to supernova and inertial confinement fusion science. The morphology of the BDI has been characterized for the first time. This work steps through the parameter space covered in Mie scattering experiments, and how the different parameters contribute to development of structures and mixing. It also examines a scaling of the Atwood number for expanding predictive capabilities to other experimental conditions and simulations. The first collection of velocity fields acquired for the BDI are recorded, and subsequent analysis evaluating the distribution of kinetic energy throughout space and time for two density ratios from the overall parameter space, as well as the transition to turbulence, estimated from a Reynolds number calculated based on momentum mixing are all presented. This information is useful in advancing the development of models to predict physics of high energy density applications where experiments are not always readily available. This research has successfully demonstrated understanding for the time criteria defining regimes where the shock driven (Richtmyer-Meshkov instability) and the buoyancy driven (Rayleigh-Taylor instability) dominates through a parametric study of density variation (Atwood number) and driver speed (Mach number). All this furthers understanding of how the BDI pertains to SN and ICF.
79 ASTRONOMY AND ASTROPHYSICS↗
A shock tube study of fuel concentration effect on high-pressure autoignition delay of ammonia
Not Available
Peng, Yuzhe↗
A numerical study of the spectral radiative properties of packed bed with mixed bauxite and silica spheres
Bauxite and silica particles have gained increasing attention for applications in the field of concentrated solar power. In this work, a Monte Carlo ray-tracing simulation is performed to predict the radiative properties (absorptance, reflectance, and transmittance) of packed beds with mixed bauxite and silica spherical particles at wavelengths of 0.5, 2.6, 9.0, and 9.35 µm. These wavelengths are representative for the visible, near-infrared, and the mid-infrared regions that are important for solar and thermal radiation, respectively. A repeating unit-column approach is used to mathematically represent the particle bed. The effects of particle mixing ratio, volume fraction, and wavelength on the predicted radiative properties are examined. The obtained radiative properties are inputted to an inverse method to retrieve the effective absorption and scattering coefficients as well as the scattering albedo, which may be later used in a continuous-scale radiative heat transfer analysis. Furthermore, the independent scattering model is used to obtain the absorption coefficient and scattering albedo based on the absorption and scattering cross sections predicted by a Monte Carlo algorithm for a single particle. It is shown that the independent scattering model underpredicts the scattering coefficient for opaque particles but overpredicts the scattering coefficient for semitransparent particles for sufficiently high particle volume fractions. Here, the radiative properties calculated from the independent scattering model are compared to the full Monte Carlo simulation of the particle bed to examine the influence of particle mixing on dependent scattering.
42 ENGINEERING↗
Multifidelity validation of digital surrogates using variable-density turbulent mixing models
In this study, ensembles of experimental data are presented and utilized to compare and validate two models used in the simulation of variable-density (Atwood = 0.22), compressible turbulent mixing. Though models of this kind (Reynolds averaged NavierStokes and large-eddy simulations) have been validated extensively with more canonical flows in previous studies, here the present approach offers novelty in the complexity of the geometry, the ensemble-based validation, and the uniformity of the computational framework on which the models are tested. Moreover, all experimental and computational tasks were completed by the authors which has led to a tightly coupled experimental configuration with its “digital twin.” The experimental divergent-shock-tube facility and its data acquisition methods are described and replicated in simulation space. A 2D Euler model which neglects the turbulent mixing at the interface is optimized to experimental data using a Gaussian process. This model then serves as the basis for both the 2D RANS and 3D LES studies that make comparisons to the mixing-layer data from the experiment. A relatively simple RANS model is shown to produce good agreement with experimental data only at late flow development times. The LES ensembles generally show good agreement with experimental data but display sensitivity to the characterization of initial conditions. Resolution-dependent behavior is also observed for certain higher-order statistics of interest. Overall, the LES model successfully captures the effects of divergent geometry, compressibility, and combined nonlinear instabilities inherent to the problem. The successful prediction of mixing width and its growth rate highlight the existence of three distinct regimes in the development of the instability, each with similarities to previously studied instabilities.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Laser Spark Evolution in an Ethylene Jet in Supersonic Crossflow Configuration
Not provided.
Mechanics↗
Experimental characterization of extreme temperature granular flows for solar thermal energy transport and storage
High-temperature, dense granular flows along an inclined plane were considered for solar thermal energy transport and storage with sintered bauxite particles. A series of experiments was performed for particle inlet temperatures of ~ 200, 400, 600, and 800 °C to understand the mechanisms of granular flows at extreme temperatures. Mass flow rates were measured using a load cell and free-surface velocities were measured and computed using particle image velocimetry. Surface temperatures were measured using infrared cameras. A significant decrease in steady-state particle mass flow rate was observed with increasing temperature due to changing flow properties. A decrease in bulk particle free-surface velocities was observed at higher temperatures. Free-surface velocity measurement error between experiments were within 20% of the average. The particle surface temperatures decreased from inlet to outlet with larger gradients at higher temperatures observed due to increasing convection and radiative heat losses. Here, a decrease in temperature was observed along the side walls due to a decrease in particle velocities.
14 SOLAR ENERGY↗
Experimental Investigation of Fiber-Foam Rheology in Advanced Multiphase Forming Systems.
Abstract not provided.
Ahmad, Michael↗
Advanced Characterization of Particulate Flows for Concentrating Solar Power Applications
The overarching goal of this project was to gain a greater fundamental understanding of heat and mass transfer in particulate-media in concentrated solar power (CSP) applications for thermal energy storage (TES) and to disseminate results to support parallel Gen3 research initiatives. Project objectives were achieved through three planned project phases to systematically characterize the heat transfer and flow properties for particulate (granular) flows at elevated temperatures up to 800 °C. These objectives were accomplished using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures. This work addressed a serious gap within the field related to the understanding and modeling of granular flow behavior and the related heat transfer at different temperatures, which directly correspond to the operating points of CSP applications which use particles for heat storage.
14 SOLAR ENERGY↗
Deep Learning and Natural Language Processing for Accelerated Inverse Design of Optical Metamaterials
Optical metamaterial device design has enjoyed a long track of success over the past 50 years leading to the manipulation of light over a wide range of wavelengths spanning the ultraviolet to the far infrared. The manipulation of light over such wavelengths has already led to many technological advancements such as the design of selective radiative absorbers for solar energy, daytime passive cooling using deep space, and optical invisibility cloaks for defense applications. Further disruptive advancements in energy, defense, computing, and biomedical fields could be enabled or enhanced by future optical metamaterial devices. These technologies could lead to increased energy efficiency and hence reduced national primary energy consumption, cheap long duration energy storage, and next generation solid-state heat engines. But historically the methods to invent and develop all of these devices have been time- consuming and based mostly on intuition and iteration. Finding an optimal design can take years.
36 MATERIALS SCIENCE↗
Deep Learning and Natural Language Processing for Accelerated Inverse Design of Optical Metamaterials
Optical metamaterial device design has enjoyed a long track of success over the past 50 years leading to the manipulation of light over a wide range of wavelengths spanning the ultraviolet to the far infrared. The manipulation of light over such wavelengths has already led to many technological advancements such as the design of selective radiative absorbers for solar energy, daytime passive cooling using deep space, and optical invisibility cloaks for defense applications. Further disruptive advancements in energy, defense, computing, and biomedical fields could be enabled or enhanced by future optical metamaterial devices. These technologies could lead to increased energy efficiency and hence reduced national primary energy consumption, cheap long duration energy storage, and next generation solid-state heat engines. But historically the methods to invent and develop all of these devices have been time- consuming and based mostly on intuition and iteration. Finding an optimal design can take years. In this project we developed a machine learning-based algorithm capable of automatically generating device designs to produce desired optical properties, reducing the design cycle life in certain situations to be almost instantaneous.
36 MATERIALS SCIENCE↗
Three-dimensional simulations of reshocked inclined Richtmyer-Meshkov instability: Effects of initial perturbations
The effect of initial perturbations on the evolution of the inclined Richtmyer-Meshkov turbulent mixing layer before and after reshock initiated by a shock wave with Mach number 1.55 is investigated through three-dimensional (3D) simulations using the flash code. The 3D simulations aim to reproduce both predominantly single-mode and multimode interfaces between light and heavy gases (N 2 -CO 2 , Atwood number, A≈0.22; amplitude to wavelength ratio of 0.088) which were created in an inclined shock tube facility to analyze the effects of initial conditions on mixing development in the entire flow field. The two-dimensional center slices of 3D simulations are compared with the experimental results to validate the computational code. Mixing width, mixed mass, mixed-mass thickness, and circulation in addition to concentration fields are shown to be in good agreement with the experimental data. The three-dimensional density and vorticity fields are first presented to qualitatively describe the flow behavior before and after reshock. Several measured density/velocity-related quantities indicate that the growth of the mixing material is strongly dependent on initial conditions. Before reshock and at early times after reshock, flow is clearly maintaining the memory of initial perturbations. However, at late time after reshock, although the large wavelength feature still dominates the flow motion, and the morphology of the two different interfaces indicates several differences, by breakdown of large-scale coherent structures to much finer scales, the memory of small scales of the multimode initial perturbation is not as clear as pre-reshock. Regarding three-dimensionality of the flow, before reshock in the multimode case, the baroclinic vorticity production, circulation, turbulent kinetic energy, and turbulent mass flux suggest that the small-scale roll-up features along the large inclined wavelength quickly evolves in all three dimensions. The coherent vortex tubes break down to smaller wormlike vortex structures, and turbulent fluctuations in the out-of-plane dimension are comparable to the spanwise direction. After reshock, this three-dimensionality of mixing growth was observed in the flow for both initial conditions. The results of this work represent a significant extension of previous computational studies performed on this specific topic. A different code with a different numerical method is validated through comparison with the experimental data. The initial perturbations are directly measured from the experimental results. Moreover, the entire three-dimensional experimental shock tube domain is simulated, and more quantities are investigated to understand the mixing mechanism and instability evolution in all three dimensions.
42 ENGINEERING↗