Search NASA⌕ Search

Engineering topics

Rapp, Vi H.

Publications and source records attributed to Rapp, Vi H..

Matching diverse feedstocks to conversion processes for the future bioeconomy

A wide variety of wasted or underutilized organic feedstocks can be leveraged to build a sustainable bioeconomy, ranging from crop residues to food processor residues and municipal wastes. Leveraging these feedstocks is both high-risk and high-reward. Converting mixed, variable, and/or highly contaminated feedstocks can pose engineering and economic challenges. However, converting these materials to fuels and chemicals can divert waste from landfills, reduce fugitive methane emissions, and enable more responsible forest management to reduce the frequency and severity of wildfires. Historically, low-value components, including ash and lignin, are poised to become valuable coproducts capable of supplementing cement and valuable chemicals. Here, we evaluate the challenges and opportunities associated with converting a range of feedstocks to renewable fuels and chemicals.

09 BIOMASS FUELS↗

Fraction of Free-Base Nicotine in Simulated Vaping Aerosol Particles Determined by X-ray Spectroscopies

A new generation of electronic cigarettes is exacerbating the youth vaping epidemic by incorporating additives that increase the acidity of generated aerosols, which facilitate uptake of high nicotine levels. We need to better understand the chemical speciation of vaping aerosols to assess the impact of acidification. Here we used X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to probe the acid-base equilibria of nicotine in hydrated vaping aerosols. Here we show that, unlike the behavior observed in bulk water, nicotine in the core of aqueous particles was partially protonated when the pH of the nebulized solution was 10.4, with a fraction of free-base nicotine (α FB ) of 0.34. Nicotine was further protonated by acidification with equimolar addition of benzoic acid (α FB = 0.17 at pH 6.2). By contrast, the degree of nicotine protonation at the particle surface was significantly lower, with 0.72 < α FB < 0.80 in the same pH range. The presence of propylene glycol and glycerol completely eliminated protonation of nicotine at the surface (α FB = 1) while not affecting significantly its acid-base equilibrium in the particle core. These results provide a better understanding of the role of acidifying additives in vaping aerosols, supporting public health policy interventions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A systematic method for selecting molecular descriptors as features when training models for predicting physiochemical properties

Machine learning has proven to be a powerful tool for accelerating biofuel development. Although numerous models are available to predict a range of properties using chemical descriptors, there is a trade-off between interpretability and performance. Neural networks provide predictive models with high accuracy at the expense of some interpretability, while simpler models such as linear regression often lack in accuracy. In addition to model architecture, feature selection is also critical for developing interpretable and accurate predictive models. We present a method for systematically selecting molecular descriptor features and developing interpretable machine learning models without sacrificing accuracy. Our method simplifies the process of selecting features by reducing feature multicollinearity and enables discoveries of new relationships between global properties and molecular descriptors. To demonstrate our approach, we developed models for predicting melting point, boiling point, flash point, yield sooting index, and net heat of combustion with the help of the Tree-based Pipeline Optimization Tool (TPOT). For training, we used publicly available experimental data for up to 8351 molecules. Our models accurately predict various molecular properties for organic molecules (mean absolute percent error (MAPE) ranges from 3.3% to 10.5%) and provide a set of features that are well-correlated to the property. This method enables researchers to explore sets of features that significantly contribute to the prediction of the property, offering new scientific insights. To help accelerate early stage biofuel research and development, we also integrated the data and models into a open-source, interactive web tool.

09 BIOMASS FUELS↗

Safety and effectiveness of a non-electric infant warmer for hypothermia in Rwanda: A cluster-randomized stepped-wedge trial

Background: Neonatal hypothermia is a common source of morbidity and mortality in low resource settings. We developed the Dream Warmer, a low cost, re-usable non-electric infant warmer to prevent and treat hypothermia. Methods: We conducted a cluster-randomized stepped-wedge trial. The primary aim was to assess the effect on overall euthermia rates of introducing the warmer compared to standard of care in rural Rwandan hospitals. The secondary aims were to assess effects of warmer introduction on mortality, as well as the safety and feasibility of the warmer. Ten district hospitals participated in the study from November 19th 2019 to July 15th 2020. Patients were eligible to use the warmer if they were 1) hypothermic (temp < 36·5 °C) or 2) or at risk of hypothermia (weight < 2·5 kg or estimated post menstrual age < 35 weeks) when Kangaroo Mother Care was not available. An encounter was defined as the data from an individual infant on a single day. Trial of a Non Electric Infant Warmer for Prevention and Treatment of Hypothermia in Rwanda [NCT03890211]. Findings: Over the study period, 3179 patients were enrolled across the ten neonatal wards, yielding 12,748 encounters; 464 unique infants used the warmer 892 times, 79% eligible due to hypothermia. Because of limited study nurse resources, the warmer was used in only 18% of eligible encounters. Despite this low rate of warmer use, the rate of euthermia rose from 51% (95% CI 50–52%) of encounters pre-intervention to 67% (66–68%) post-intervention; p < 0·0001. Among the encounters in which the warmer was used, only 11% (9–13%) remained hypothermic. While mortality rates pre- and post-intervention did not change, mortality rate among those who used the warmer was significantly lower than among those who did not (0·9% vs 2·8%, p = 0·01). Use of the warmer did not affect hyperthermia rates. There were no safety concerns or instances of incorrect warmer use. Interpretation: Introduction of the warmer increased rates of euthermia with no associated safety concerns.

60 APPLIED LIFE SCIENCES↗

Emissions from Heated Terpenoids Present in Vaporizable Cannabis Concentrates

Vaporizable cannabis concentrates (VCCs) consumed as a liquid (vaping) or a waxy solid (dabbing) are becoming increasingly popular. However, their associated emissions and impacts have not been fully described. Mixtures containing different proportions of 12 VCC terpenoids and high MW compounds were heated at 100-500 °C inside a room-sized chamber to simulate emissions. Terpenoids, thermal degradation byproducts, and ultrafine particles (UFPs) were quantified in the chamber air. Air samples contained over 50% of emitted monoterpenes and less than 40% of released sesquiterpenes and terpene alcohols. Eleven degradation byproducts were quantified, including acrolein (1.3-3.9 μg m -3 ) and methacrolein (2.0 μg m -3 ). A large amount of UFPs were released upon heating and remained airborne for at least 3 h. The mode diameter increased from 80 nm at 100 °C to 140 nm at 500 °C, and particles smaller than 250 nm contributed to 90% of PM 1.0 . Here, the presence of 0.5% of lignin, flavonoid, and triterpene additives in the heated mixtures resulted in a threefold increase in the particle formation rate and PM 1.0 concentration, suggesting that these high-molecular-weight compounds enhanced aerosol inception and growth. Predicted UFP emission rates in typical consumption scenarios (6 × 10 11 -2 × 10 13 # min -1 ) were higher than, or comparable with, other common indoor sources such as smoking and cooking.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimization of Secondary Air Injection in a Wood-Burning Cookstove: An Experimental Study

Nearly 40% of the world's population regularly cooks on inefficient biomass stoves that emit harmful airborne pollutants, such as particulate matter (PM). Secondary air injection can significantly reduce PM mass emissions to mitigate the health and climate impacts associated with biomass cookstoves. However, secondary air injection can also increase the number of ultrafine particles emitted, which may be more harmful to health. This research investigates the effect of secondary air injection on the mass and size distribution of PM emitted during solid biomass combustion. An experimental wood-burning cookstove platform and parametric testing approach are presented to identify and optimize secondary air injection parameters that reduce PM and other harmful pollutants. Size-resolved measurements of PM emissions were collected and analyzed as a function of parametric stove design settings. The results show that PM emissions are highly sensitive to secondary air injection flow rate and velocity. Although increasing turbulent mixing (through increased velocity) can promote more complete combustion, increasing the total flow rate of secondary air may cause localized flame quenching that increases particle emissions. As a result, biomass cookstoves that implement secondary air injection should be carefully optimized and validated to ensure that PM emission reductions are achieved throughout the particle size range.

54 ENVIRONMENTAL SCIENCES↗

Verifying mixing in dilution tunnels How to ensure cookstove emissions samples are unbiased

A well-mixed diluted sample is essential for unbiased measurement of cookstove emissions. Most cookstove testing labs employ a dilution tunnel, also referred to as a “duct,” to mix clean dilution air with cookstove emissions before sampling. It is important that the emissions be well-mixed and unbiased at the sampling port so that instruments can take representative samples of the emission plume. Some groups have employed mixing baffles to ensure the gaseous and aerosol emissions from cookstoves are well-mixed before reaching the sampling location [2, 4]. The goal of these baffles is to to dilute and mix the emissions stream with the room air entering the fume hood by creating a local zone of high turbulence. However, potential drawbacks of mixing baffles include increased flow resistance (larger blowers needed for the same exhaust flow), nuisance cleaning of baffles as soot collects, and, importantly, the potential for loss of PM2.5 particles on the baffles themselves, thus biasing results. A cookstove emission monitoring system with baffles will collect particles faster than the duct’s walls alone. This is mostly driven by the available surface area for deposition by processes of Brownian diffusion (through the boundary layer) and turbophoresis (i.e. impaction). The greater the surface area available for diffusive and advection-driven deposition to occur, the greater the particle loss will be at the sampling port. As a layer of larger particle “fuzz” builds on the mixing baffles, even greater PM2.5 loss could occur. The micro structure of the deposited aerosol will lead to increased rates of particle loss by interception and a tendency for smaller particles to deposit due to impaction on small features of the micro structure. If the flow stream could be well-mixed without the need for baffles, these drawbacks could be avoided and the cookstove emissions sampling system would be more robust.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

A high turndown, ultra low emission low swirl burner for natural gas, on-demand water heaters

Previous research has shown that on-demand water heaters are, on average, approximately 37% more efficient than storage water heaters. However, approximately 98% of water heaters in the U.S. use storage water heaters while the remaining 2% are on-demand. A major market barrier to deployment of on-demand water heaters is their high retail cost, which is due in part to their reliance on multi-stage burner banks that require complex electronic controls. This project aims to research and develop a cost-effective, efficient, ultra-low emission burner for next generation natural gas on-demand water heaters in residential and commercial buildings. To meet these requirements, researchers at the Lawrence Berkeley National Laboratory (LBNL) are adapting and testing the low-swirl burner (LSB) technology for commercially available on-demand water heaters. In this report, a low-swirl burner is researched, developed, and evaluated to meet targeted on-demand water heater performance metrics. Performance metrics for a new LSB design are identified by characterizing performance of current on-demand water heaters using published literature and technical specifications, and through experimental evaluations that measure fuel consumption and emissions output over a range of operating conditions. Next, target metrics and design criteria for the LSB are used to create six 3D printed prototypes for preliminary investigations. Prototype designs that proved the most promising were fabricated out of metal and tested further to evaluate the LSB’s full performance potential. After conducting a full performance evaluation on two designs, we found that one LSB design is capable of meeting or exceeding almost all the target performance metrics for on-demand water heaters. Specifically, this LSB demonstrated flame stability when operating from 4.07 kBTU/hr up to 204 kBTU/hr (50:1 turndown), compliance with SCAQMD Rule 1146.2 (14 ng/J or 20 ppm NOX @ 3% O2), and lower CO emissions than state-of-the art water heaters. Overall, the results from this research show that the LSB could provide a simple, low cost burner solution for significantly extending operating range of on-demand water heaters while providing low NOX and CO emissions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Reducing ultrafine particle emissions using air injection in wood-burning cookstoves

In order to address the health risks and climate impacts associated with pollution from cooking on biomass fires, researchers have focused on designing new cookstoves that improve cooking performance and reduce harmful emissions, specifically particulate matter (PM). One method for improving cooking performance and reducing emissions is using air injection to increase turbulence of unburned gases in the combustion zone. Although air injection reduces total PM mass emissions, the effect on PM size-distribution and number concentration has not been thoroughly investigated. Using two new wood-burning cookstove designs from Lawrence Berkeley National Laboratory, this research explores the effect of air injection on cooking performance, PM and gaseous emissions, and PM size distribution and number concentration. Both cookstoves were created using the Berkeley-Darfur Stove as the base platform to isolate the effects of air injection. The thermal performance, gaseous emissions, PM mass emissions, and particle concentrations (ranging from 5 nm to 10 μm in diameter) of the cookstoves were measured during multiple high-power cooking tests. Finally, the results indicate that air injection improves cookstove performance and reduces total PM mass but increases total ultrafine (less than 100 nm in diameter) PM concentration over the course of high-power cooking.

54 ENVIRONMENTAL SCIENCES↗

Effect of Fuel Wobbe Number on Pollutant Emissions from Advanced Technology Residential Water Heaters: Results of Controlled Experiments

The research summarized in this report is part of a larger effort to evaluate the potential air quality impacts of using liquefied natural gas in California. A difference of potential importance between many liquefied natural gas blends and the natural gas blends that have been distributed in California in recent years is the higher Wobbe number of liquefied natural gas. Wobbe number is a measure of the energy delivery rate for appliances that use orifice- or pressure-based fuel metering. The effect of Wobbe number on pollutant emissions from residential water heaters was evaluated in controlled experiments. Experiments were conducted on eight storage water heaters, including five with “ultra low-NO X ” burners, and four on-demand (tankless) water heaters, all of which featured ultra low-NO X burners. Pollutant emissions were quantified as air-free concentrations in the appliance flue and fuel-based emission factors in units of nanogram of pollutant emitter per joule of fuel energy consumed. Emissions were measured for carbon monoxide (CO), nitrogen oxides (NO X ), nitrogen oxide (NO), formaldehyde and acetaldehyde as the water heaters were operated through defined operating cycles using fuels with varying Wobbe number. The reference fuel was Northern California line gas with Wobbe number ranging from 1344 to 1365. Test fuels had Wobbe numbers of 1360, 1390 and 1420. The most prominent finding was an increase in NO X emissions with increasing Wobbe number: all five of the ultra low-NO X storage water heaters and two of the four ultra low-NO X on-demand water heaters had statistically discernible (p<0.10) increases in NO X with fuel Wobbe number. The largest percentage increases occurred for the ultra low-NO X water heaters. There was a discernible change in CO emissions with Wobbe number for all four of the on-demand devices tested. The on-demand water heater with the highest CO emissions also had the largest CO increase with increasing fuel Wobbe number.

03 NATURAL GAS↗

Predicting Backdrafting and Spillage for Natural-Draft Gas Combustion Appliances: Validating VENT-II

VENT-II is a computer program designed to provide detailed analysis of natural draft and induced draft combustion appliance vent-systems (i.e., furnace or water heater). This program is capable of predicting house depressurization thresholds that lead to backdrafting and spillage of combustion appliances; however, validation reports of the program being applied for this purpose are not readily available. The purpose of this report is to assess VENT-II’s ability to predict combustion gas spillage events due to house depressurization by comparing VENT-II simulated results with experimental data for four appliance configurations. The results show that VENT-II correctly predicts depressurizations resulting in spillage for natural draft appliances operating in cold and mild outdoor conditions, but not for hot conditions. In the latter case, the predicted depressurizations depend on whether the vent section is defined as part of the vent connector or the common vent when setting up the model. Overall, the VENTII solver requires further investigation before it can be used reliably to predict spillage caused by depressurization over a full year of weather conditions, especially where hot conditions occur.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Assessment of Literature Related to Combustion Appliance Venting Systems

In many residential building retrofit programs, air tightening to increase energy efficiency is constrained by concerns about related impacts on the safety of naturally vented combustion appliances. Tighter housing units more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spillage. Several test methods purportedly assess the potential for depressurization-induced backdrafting and spillage, but these tests are not robustly reliable and repeatable predictors of venting performance, in part because they do not fully capture weather effects on venting performance. The purpose of this literature review is to investigate combustion safety diagnostics in existing codes, standards, and guidelines related to combustion appliances. This review summarizes existing combustion safety test methods, evaluations of these test methods, and also discusses research related to wind effects and the simulation of vent system performance. Current codes and standards related to combustion appliance installation provide little information on assessing backdrafting or spillage potential. A substantial amount of research has been conducted to assess combustion appliance backdrafting and spillage test methods, but primarily focuses on comparing short-term (stress) induced tests and monitoring results. Monitoring, typically performed over one week, indicated that combinations of environmental and house operation characteristics most conducive to combustion spillage were rare. Research, to an extent, has assessed existing combustion safety diagnostics for house depressurization, but the objectives of the diagnostics, both stress and monitoring, are not clearly defined. More research is also needed to quantify the frequency of test “failure” occurrence throughout the building stock and assess the statistical effects of weather (especially wind) on house depressurization and in turn on combustion appliance venting. Incorporating weather variations and house ventilation system characteristics in existing simulation software may assist such analyses and with developing a more reliable diagnostic for use on-site.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Extending lean operating limit and reducing emissions of methane spark-ignited engines using a microwave-assisted spark plug

A microwave-assisted spark plug was used to extend the lean operating limit (lean limit) and reduce emissions of an engine burning methane-air. In-cylinder pressure data were collected at normalized air-fuel ratios of λ = 1.46, λ = 1.51, λ = 1.57, λ = 1.68, and λ = 1.75. For each λ , microwave energy (power supplied to the magnetron per engine cycle) was varied from 0 mJ (spark discharge alone) to 1600 mJ. At lean conditions, the results showed adding microwave energy to a standard spark plug discharge increased the number of complete combustion cycles, improving engine stability as compared to spark-only operation. Addition of microwave energy also increased the indicated thermal efficiency by 4% at λ = 1.68. At λ = 1.75, the spark discharge alone was unable to consistently ignite the air-fuel mixture, resulting in frequent misfires. Although microwave energy produced more consistent ignition than spark discharge alone at λ = 1.75, 59% of the cycles only partially burned. Overall, the microwave-assisted spark plug increased engine performance under lean operating conditions (λ = 1.68) but did not affect operation at conditions closer to stoichiometric.

Rapp, Vi H.↗