Engineering topics

Raut, Aniket

Publications and source records attributed to Raut, Aniket.

5 records

DOE OSTI2024

Template-Assisted Growth of High-Quality α-Phase FAPbI 3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS 2 Nanosheets

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Determination of the Interfacial Energy between Graphene Nanoplatelets and Deuterated or Hydrogenated Polystyrene

The tracer diffusion coefficients of various graphene nanoplatelet-polystyrene (GNP-PS) systems were determined by using dynamic secondary ion mass spectrometry, which provided insights into the interactions within the polymer nanocomposite system. Bilayer films, where one contained trace amounts of deuterated polystyrene (dPS), were produced, and the interdiffusion was measured by detecting the position of the dPS interface. GNPs were placed in both or only one of the two layers. The diffusion coefficient was decreased when GNPs were present in both layers as compared to the samples without GNP, indicating an attractive interaction between GNP and polystyrene. Surprisingly, the coefficient increased relative to the control when GNPs were present only in the PS containing layer, whereas it decreased most strongly when GNP and dPS were present only in the same layer, indicating that an additional preference existed for GNPs and dPS. A significant difference in interfacial energies was measured using contact angle goniometry of PS or dPS droplets on flat GNP layers, confirming the preferential interaction. DFT calculations were used to calculate the interfacial interaction between GNP and dPS or PS, and they showed an attractive potential which was maximal when the PS rings were conformal with the GNP structure. Furthermore, the differential energy between PS and dPS at the GNP interface was in excellent agreement with the measured value. In contrast, contact angle goniometry indicated that the interaction between GNP and poly(methyl methacrylate) (PMMA) was unfavorable, and no difference in interfacial energy between dPMMA and PMMA was observed. Therefore, these techniques can provide a means for determining the relative affinity between GNP and different polymer hosts, which can be an important consideration in the mechanics and adhesion properties of the compounds.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Migration and Precipitation of Platinum in Anion‐Exchange Membrane Fuel Cells

Abstract Despite the recent progress in increasing the power generation of Anion‐exchange membrane fuel cells (AEMFCs), their durability is still far lower than that of Proton exchange membrane fuel cells (PEMFCs). Using the complementary techniques of X‐ray micro‐computed tomography (CT), Scanning Electron Microscopy (SEM) and Energy Dispersive X‐ray (EDX) spectroscopy, we have identified Pt ion migration as an important factor to explain the decay in performance of AEMFCs. In alkaline media Pt +2 ions are easily formed which then either undergo dissolution into the carbon support or migrate to the membrane. In contrast to PEMFCs, where hydrogen cross over reduces the ions forming a vertical “Pt line” within the membrane, the ions in the AEM are trapped by charged groups within the membrane, leading to disintegration of the membrane and failure. Diffusion of the metal components is still observed when the Pt/C of the cathode is substituted with a FeCo−N−C catalyst, but in this case the Fe and Co ions are not trapped within the membrane, but rather migrate into the anode, thereby increasing the stability of the membrane.

Raut, Aniket↗

DOE OSTI2023

Migration and Precipitation of Platinum in Anion–Exchange Membrane Fuel Cells

Despite the recent progress in increasing the power generation of Anion-exchange membrane fuel cells (AEMFCs), their durability is still far lower than that of Proton exchange membrane fuel cells (PEMFCs). Using the complementary techniques of X-ray micro-computed tomography (CT), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy, we have identified Pt ion migration as an important factor to explain the decay in performance of AEMFCs. In alkaline media Pt+2 ions are easily formed which then either undergo dissolution into the carbon support or migrate to the membrane. In contrast to PEMFCs, where hydrogen cross over reduces the ions forming a vertical “Pt line” within the membrane, the ions in the AEM are trapped by charged groups within the membrane, leading to disintegration of the membrane and failure. Furthermore, diffusion of the metal components is still observed when the Pt/C of the cathode is substituted with a FeCo–N–C catalyst, but in this case the Fe and Co ions are not trapped within the membrane, but rather migrate into the anode, thereby increasing the stability of the membrane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Application of the core shell model for strengthening polymer filament interfaces

While surface segregation has been intensively studied in thin films, relatively little has been investigated in filament geometries. In contrast to thin films, the filament surface forms a continuum, with interactions both at the free air and internal filament interface, which makes it difficult to achieve an equilibrium configuration. This asymmetry has become particularly apparent with the increasing use of additive manufacturing where entire structures are constructed via layered deposition of filamentous layers from a moving thermal nozzle. In addition, this process is highly non-equilibrated with poor thermal retention and is responsible for insufficient filament–filament interfacial fusion and internal pore formation along the printing direction. These features all contribute to poor mechanical and structural properties, which are exacerbated in semi-crystalline polymers, such as Polylactic Acid (PLA), where the melting point, T m , is much higher than the glass transition, T g . Even though system is liquid the molecules become ordered within the crystal structure and this ordering interferes with interdiffusion, which in turn prevents proper interfacial fusion. Capitalizing on the differential in surface tension, we show that addition of less than 1%, or trace amounts, of longer chain polymers, an oriented core shell structure, will be formed with a self-limiting thickness of three time the radius of gyration, R g , of the tracer chains. The lower T g of the tracers and their orientation makes them poised for interdiffusion when subsequent layers are deposited producing structures with significant improvement of the mechanical properties and internal structural integrity.

36 MATERIALS SCIENCE↗