Engineering topics

Reddy, C. S.

Publications and source records attributed to Reddy, C. S..

9 records

NASA NTRS1988

Modeling effects on the prediction of aerodynamic performance of a double-delta wing

A numerical investigation is undertaken of an 80/65-deg double-delta flat wing by means of the free vortex sheet method that views the vortex system on the leading edge in three different ways, in order to assess the effect of the model's type on the aerodynamic performance of the wing. The model employing two separate vortex systems, one each on inward and outward leading edges, yields predictions that are in close agreement with experimental data, although the model with single-vortex representation is adequate and requires less computational time.

Reddy, C. S.↗

NASA NTRS1987

Spanwise pressure distribution on delta wing with leading-edge vortex flap

The aerodynamic characteristics of a highly swept planar delta wing employing conical leading edge flaps are numerically investigated, using a free vortex sheet method that is based on an advanced, three-dimensional inviscid flow panel method employing quadratic doublet distributions to represent the wing surface and the rolled-up vortex sheet and wake. Upward flap deflection shifts the negative pressure peak inboard of the basic wing and develops a significant suction pressure on the flap that then produces thrust component in the direction of flight; overall drag is thereby reduced.

Reddy, C. S.↗

NASA NTRS1982

Aerodynamic performance of slender wings with separated flows

The aerodynamic performance of low aspect ratio sweptback wings with vortex flows was numerically investigated using the free vortex sheet method. The models studied included flat, cambered, strake, and leading edge flapped wings of different planforms. The theoretical results predicted by the method were compared with the existing experimental data wherever available; and the code capabilities and limitations were explored. Also the effects of the wing thickness, fuselage, leading edge flap and multiple vortex modeling on the aerodynamic characteristics were studied.

Reddy, C. S.↗

NASA NTRS1981

Effect of leading-edge vortex flaps on aerodynamic performance of delta wings

The effect of leading-edge vortex flaps on the aerodynamic characteristics of highly swept-back wings is analytically investigated, using the free vortex sheet method. The method, based on a three-dimensional inviscid flow model, is an advanced panel type employing quadratic doublet distributions to represent the wing surface, rolled-up vortex sheet and wake and is capable of computing forces, moments and surface pressures.

Reddy, C. S.↗

NASA NTRS1981

Effect of sweep angles on aerodynamic performance of double arrow wing - An analytical study

Hybrid wing planforms are studied for adoption on supersonic transport and fighter aircraft. The free vortex sheet method is used to determine effects of the leading-edge sweep angles on the aerodynamic performance of a double arrow wing with a strake. Results show lift and drag increase with the increase of the inboard and outboard leading-edge sweep angles. However, the lift-to-drag ratio is little influenced by the changes in these sweep angles. Spanwise surface pressure distributions on the aft region are influenced by the inboard sweep angle while the outboard sweep angle has no effect on these pressures. Finally, the experimental data and predicted results are compared to show good agreement.

Reddy, C. S.↗

NASA NTRS1981

Investigation of aerodynamic characteristics of wings having vortex flow using different numerical codes

The aerodynamic characteristics of highly sweptback wings having separation-induced vortex flow were investigated by employing different numerical codes with a view to determining some of the capabilities and limitations of these codes. Flat wings of various configurations-strake wing models, cropped, diamond, arrow and double delta wings, were studied. Cambered and cranked planforms have also been tested. The theoretical results predicted by the codes were compared with the experimental data, wherever possible, and found to agree favorably for most of the configurations investigated. However, large cambered wings could not be successfully modeled by the codes. It appears that the final solution in the free vortex sheet method is affected by the selection of the initial solution. Accumulated span loadings estimated for delta and diamond wings were found to be unusual in comparison with attached flow results in that the slopes of these load curves near the leading edge do not tend to infinity as they do in the case of attached flow.

Reddy, C. S.↗

NASA NTRS1980

Analytical investigation of aerodynamic characteristics of highly swept wings with separated flow

Many modern aircraft designed for supersonic speeds employ highly swept-back and low-aspect-ratio wings with sharp or thin edges. Flow separation occurs near the leading and tip edges of such wings at moderate to high angles of attack. Attempts have been made over the years to develop analytical methods for predicting the aerodynamic characteristics of such aircraft. Before any method can really be useful, it must be tested against a standard set of data to determine its capabilities and limitations. The present work undertakes such an investigation. Three methods are considered: the free-vortex-sheet method (Weber et al., 1975), the vortex-lattice method with suction analogy (Lamar and Gloss, 1975), and the quasi-vortex lattice method of Mehrotra (1977). Both flat and cambered wings of different configurations, for which experimental data are available, are studied and comparisons made.

Reddy, C. S.↗

NASA NTRS1980

Development of a vortex-lift-design method and application to a slender maneuver-wing configuration

A method has been developed to optimize the mean camber surface of a cranked slender wing having leading-edge vortex flow at transonic-maneuver conditions using the suction analogy. This type of flow was assumed because it was anticipated that the slenderness of the wing would preclude attached flow at the required lift coefficient. A constraint was imposed in that the camber deflections were to be restricted by a realistic structural-box requirement. The resulting application yielded mean-camber shapes which produced effective suction levels equivalent to 77 percent of the full-planar leading-edge value at the design lift coefficient.

Lamar, J. E.↗

NASA NTRS1979

Theoretical study of aerodynamic characteristics of wings having vortex flow

The aerodynamic characteristics of slender wings having separation induced vortex flows are investigated by employing three different computer codes--free vortex sheet, quasi vortex lattice, and suction analogy methods. Their capabilities and limitations are examined, and modifications are discussed. Flat wings of different configurations: arrow, delta, and diamond shapes, as well as cambered delta wings, are studied. The effect of notch ratio on the load distributions and the longitudinal characteristics of a family of arrow and diamond wings is explored. The sectional lift coefficients and the accumulated span loadings are determined for an arrow wing and are seen to be unusual in comparison with the attached flow results. The theoretically predicted results are compared with the existing experimental values.

Reddy, C. S.↗