Vacancy-Enabled O3 Phase Stabilization for Manganese-Rich Layered Sodium Cathodes
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Engineering topics
Reed, D.
Publications and source records attributed to Reed, D..
The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: Boeing Helicopters airframe finite element modeling
Mathematical models based on the finite element method of structural analysis, as embodied in the NASTRAN computer code, are routinely used by the helicopter industry to calculate airframe static internal loads used for sizing structural members. Historically, less reliance has been placed on the vibration predictions based on these models. Beginning in the early 1980's NASA's Langley Research Center initiated an industry wide program with the objective of engendering the needed trust in vibration predictions using these models and establishing a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process. Emphasis in this paper is placed on the successful modeling of the Army/Boeing CH-47D which showed reasonable correlation with test data. A principal finding indicates that improved dynamic analysis requires greater attention to detail and perhaps a finer mesh, especially the mass distribution, than the usual stress model. Post program modeling efforts show improved correlation placing key modal frequencies in the b/rev range with 4 percent of the test frequencies.
Gabel, R.↗
The NASA/Industry Design Analysis Methods for Vibrations (DAMVIBS) Program - Boeing helicopters airframe finite element modeling
Finite-element modeling of the airframe vibration of the Army/Boeing CH-47D helicopter is conducted with comparisons to experimental data in an effort to improve the design process. A NASTRAN FEM is developed that is fully representative of the test configuration and includes the support fixture, shakers, and the aircraft/shaker suspension system. The analysis is conducted with specific attention given to the prediction of reasonable forced amplitudes throughout the airframe. Reasonable correlation is noted between the FEM and experimental results, although improved correlation can be obtained by including more accurate damping values and secondary effects such as stringer shear loading. It is shown that the general stress model does not provide an adequate dynamic analysis on which to base design improvements. A more detailed model is required that emphasizes highly detailed helicopter elements and employs a finer mesh particularly in the description of the mass distribution.
Gabel, R.↗
Vortex shedding experiment with flat and curved bluff plates in water
Vortex shedding experiments were conducted in a water flow facility in order to simulate the strong discrete 4000-Hz vibration detected in the Space Shuttle Main Engine (SSME) which is thought to be associated with the SSME LOX inlet tee splitter vanes on the Main Injector. For the case of a flat vane with a blunt trailing edge excited by flow induced vortex shedding, lock-in with the first bending mode of the plate was observed. A curved vane displayed similar behavior, with the lock-in being a more discrete higher amplitude response. Aluminum vanes were employed to decouple the first vane bending mode from the vortex shedding mode. The application of an asymmetric 30-deg trailing edge bevel to both the flat and curved vanes was found to greatly reduce the strength of the shed vortices.
Reed, D.↗
Planning, creating and documenting a NASTRAN finite element model of a modern helicopter
Mathematical models based on the finite element method of structural analysis as embodied in the NASTRAN computer code are widely used by the helicopter industry to calculate static internal loads and vibration of airframe structure. The internal loads are routinely used for sizing structural members. The vibration predictions are not yet relied on during design. NASA's Langley Research Center sponsored a program to conduct an application of the finite element method with emphasis on predicting structural vibration. The Army/Boeing CH-47D helicopter was used as the modeling subject. The objective was to engender the needed trust in vibration predictions using these models and establish a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process.
Gabal, R.↗
Planning, creating and documenting a NASTRAN finite element model of a modern-helicopter
Mathematical models based on the finite element method of structural analysis as embodied in the NASTRAN computer code are widely used by the helicopter industry to calculate static internal loads and vibration of airframe structure. The internal loads are routinely used for sizing structural members. The vibration predictions are not yet relied on during design. NASA's Langley Research Center sponsored a program to conduct an application of the finite element method with emphasis on predicting structural vibration. The Army/Boeing CH-47D helicopter was used as the modeling subject. The objective was used to engender the needed trust in vibration predictions using these models and establish a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process.
Gabel, R.↗
NASA balloon: Aircraft ranging, data and voice experiment
A series of tests to evaluate, at L-band, the ranging, voice, and data communications concepts proposed for the air traffic control experiment of the Applications Technology Satellite-F are described. The ground station facilities, balloon platforms and the aircraft were supplied by the European Space Research Organization. One ground simulation and two aircraft flights at low elevation angles were conducted. Even under high interference conditions good performance was obtained for both voice communications and side tone ranging. High bit errors occurred in the data channels resulting in false commands. As a result of the experience gained in operating the equipment in an aircraft environment several recommendations were made for improving the equipment performance.
Wishna, S.↗