Engineering topics
Reedlunn, Benjamin
Publications and source records attributed to Reedlunn, Benjamin.
Workshop on Meshless Simulation of Empty Room Closure: Introduction.
Abstract not provided.
International Collaborations on Radioactive Waste Disposal in Salt
This report is a summary of the international collaboration and laboratory work funded by the US Department of Energy Office (DOE) of Nuclear Energy Spent Fuel and Waste Science & Technology (SFWST) as part of the Sandia National Laboratories Salt R&D work package. This report satisfies milestone level-four milestone M4SF-19SNO10303064. Several stand-alone sections make up this summary report, each completed by the participants. The first two sections discuss international collaborations on geomechanical benchmarking exercises (WEIMOS), granular salt reconsolidation (KOMPASS), engineered barriers (RANGERS), and documentation of Features, Events, and Processes (FEPs).
Mechanical Behavior of Bedded Salt Interfaces and Clay Seams Subjected to Shear ? September 2019 Update for WEIMOS.
Abstract not provided.
Initial Evaluation of WIPP Crushed Salt Model Applied to the Triaxial Compaction Test TK-031.
Abstract not provided.
Miscellaneous Topics Related to Rock Salt Constitutive Modeling.
Abstract not provided.
Mechanical Response of Additively Manufactured Stainless Steel 304L Across a Wide Range of Loading Conditions
The mechanical response of additively manufactured (AM) stainless steel 304L has been investigated across a broad range of loading conditions, covering 11 decades of strain rate, and compared with the behaviors of traditional ingot-derived (wrought) material. In general, the AM material exhibits a greater strength and reduced ductility compared with the baseline wrought form. These differences are consistently found from quasi-static and high strain rate tests. A detailed investigation of the microstructure, the defect structure, the phase, and the composition of both forms reveals differences that may contribute to the differing mechanical behaviors. Compared with the baseline wrought material, dense AM stainless steel 304L has a more complex grain structure with substantial sub-structure, a fine dispersion of ferrite, increased dislocation density, oxide dispersions and larger amounts of nitrogen. In-situ neutron diffraction studies conducted during quasi-static loading suggest that the increased strength of AM material is due to its initially greater dislocation density. The flow strength of both forms is correlated with dislocation density through a square root dependence akin to a Taylor-like relationship. Neutron diffraction measurements of lattice strains also correlate with a crystal plasticity finite element simulations of the tensile test. Other simulations predict a significant degree of elastic and plastic anisotropy due to crystallographic texture. Hopkinson tests at higher strain rates $\dot{ε}$ = 500 and 2500 s -1 ) also show a greater strength for AM stainless steel 304L; although, the differences compared with wrought are reduced at higher strain rates. Gas gun impact tests, including reverse ballistic, forward ballistic and spall tests, consistently reveal a larger dynamic strength in the AM material. The Hugoniot Elastic Limit (HEL) of AM SS 304L exceeds that of wrought material although considerable variability is observed with the AM material. Forward ballistic testing demonstrates spall strengths of AM material (3.27 -- 3.91 GPa) that exceed that of the wrought material (2.63 -- 2.88 GPa). The Hugoniot equation-of-state for AM samples matches archived data for this metal alloy.
Assessment of Meshless Methods for Simulation of Empty Room Closure at the Waste Isolation Pilot Plant.
Abstract not provided.
Enhancements to the Munson-Dawson Model for Rock Salt
The Munson-Dawson (MD) constitutive model was originally developed in the 1980's to predict the thermomechanical behavior of rock salt. Since then, it has been used to simulate the evolution of the underground in nuclear waste repositories, mines, and storage caverns for gases and liquids. This report covers three enhancements to the MD model. (1) New transient and steady-state rate terms were added to capture salt's creep behavior at low equivalent stresses (below about 8 MPa). These new terms were calibrated against a series of triaxial compression creep experiments on salt from the Waste Isolation Pilot Plant. (2) The equivalent stress measure was changed from the Tresca stress to the Hosford stress. By varying a single exponent, the Hosford stress can reduce to the Tresca stress, the von Mises stress, or a range of behaviors in-between. This exponent was calibrated against true triaxial compression experiments on salt hollow cylinders. (3) The MD model's numerical implementation was overhauled, adding a line search algorithm to the implicit solution scheme. The new implementation was verified against analytical solutions, and benchmarked against a pre-existing implementation on a room closure simulation. The new implementation pre- dicted virtually identical room closure, yet sped up the simulation by 16x . (The source code of the new implementation is included in an appendix of this report.)
Conversion of Plastic Work to Heat: A full-field study of thermomechanical coupling
This project targeted a full-field understanding of the conversion of plastic work into heat using advanced diagnostics (digital image correlation, DIC, combined with infrared, IR, imaging). This understanding will act as a catalyst for reformulating the prevalent simplistic model, which will ultimately transform Sandia's ability to design for and predict thermomechanical behavior, impacting national security applications including nuclear weapon assessments of accident scenarios. Tensile 304L stainless steel dogbones are pulled in tension at quasi-static rates until failure and full-field deformation and temperature data are captured, while accounting for thermal losses. The IR temperature fields are mapped onto the DIC coordinate system (Lagrangian formulation). The resultant fields are used to calculate the Taylor-Quinney coefficient, β, at two strain rates rates (0.002 s -1 and 0.08 s -1 ) and two temperatures (room temperature, RT, and 250°C).
Mechanical Behavior of Bedded Salt Interfaces and Clay Seams Subjected to Shear.
Abstract not provided.
Mechanical Behavior of Bedded Salt Interfaces and Clay Seams Subjected to Shear.
Abstract not provided.