Engineering topics

Regan, Sean P.

Publications and source records attributed to Regan, Sean P..

8 records

DOE OSTI2024

Spatiotemporal Reaction Dynamics Control in Two‐Photon Polymerization for Enhancing Writing Characteristics

Since 2001, 3D microfabrication based on two‐photon polymerization (TPP) has drawn extensive attention and interest in biology, optics, photonics, material science, and high‐energy physics. The in‐volume fabrication capability due to the threshold behavior of two‐photon absorption enables TPP higher flexibility compared with other nanofabrication techniques. However, as determined by the in‐volume fabrication feature as well as various reaction dynamics, the writing characteristics of TPP, such as throughput, accuracy, surface quality, and fabrication capability, are still limited. Herein, a comprehensive study is performed on the spatiotemporal behavior of reaction dynamics during TPP fabrication, mainly focusing on spatiotemporal characteristics of radical diffusion, photothermal effect, microscale mechanics, and voxel stacking process. Based on the study, a nonsequential fabrication method is established to simultaneously improve key writing characteristics of TPP and realize sharp features, high speeds, large overhang structure, and smooth surfaces. The method established in this work can be applied to improve the performance of functional devices for various fields.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Nanofabrication and inspection of fuel capsules for inertial confinement fusion

3D nanofabrication via Two-Photon Polymerization (TPP) provides a unique capability of flexibly fabricating complex structures over 1D-3D dimensions and µm-cm scales with resolutions below 100 nm. In the past years, the Laser-Assisted Nano Engineering (LANE) Group at the University of Nebraska-Lincoln (UNL) has been working closely with the Laboratory of Laser Energetics (LLE) in developing practical TPP approaches to fabricating various target structures for Inertial Confinement Fusion (ICF). At the same time, fuel capsules for ICF experiments should be inspected for surface and wall-embedded defects. Plastics materials [e.g., for example polystyrene (PS)] are the common materials used to make fuel capsules. However, during their manufacturing, capsules usually contain defects (vacuoles) embedded inside the shell walls, which may distort the implosion processes and influence the ICF performance of the capsules. The size of vacuoles is usually in a range from 100 to 2000 nm. Coherent anti-Stokes Raman scattering (CARS) microscope offers the capabilities of inspecting and characterizing the capsule defects. Furthermore, cryo-CARS microscopy was developed to explore how fuel isotope distributed inside target when icing that could not be diagnosed before.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Silicon x-ray backlighter improvement by targets with spike-like microstructures

In order to accurately probe high energy density matter states, it is vital to create powerful x-ray backlighters. One approach to create such x-ray sources is based on the usage of short-pulse, high-energy lasers, which greatly benefits from an optimization of the laser target coupling. Here, the spectral and temporal x-ray emission profiles of structured silicon targets with micron-sized spikes on the front surface are studied at laser intensities of 10 17 W cm -2 . The laser pulse length is varied between 1 and 20 ps with an energy of up to 1 kJ. The structured targets show an up to 13× enhancement of silicon He α emission compared to flat foils with a well-defined, sharp emission pulse profile. Furthermore, the performance of the microstructured targets is compared to targets with a CH shield as well as foils irradiated with a UV prepulse.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Evidence of non-Maxwellian ion velocity distributions in spherical shock-driven implosions

The ion velocity distribution functions of thermonuclear plasmas generated by spherical laser direct drive implosions are studied using deuterium-tritium (DT) and deuterium-deuterium (DD) fusion neutron energy spectrum measurements. A hydrodynamic Maxwellian plasma model accurately describes measurements made from lower temperature (< 10 keV), hydrodynamiclike plasmas, but is insufficient to describe measurements made from higher temperature more kineticlike plasmas. The high temperature measurements are more consistent with Vlasov-Fokker-Planck (VFP) simulation results which predict the presence of a bimodal plasma ion velocity distribution near peak neutron production. Furthermore, these measurements provide direct experimental evidence of non-Maxwellian ion velocity distributions in spherical shock driven implosions and provide useful data for benchmarking kinetic VFP simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Hot electron preheat in hydrodynamically scaled direct-drive inertial confinement fusion implosions on the NIF and OMEGA

Hot electron preheat has been quantified in warm, directly driven inertial confinement fusion implosions on OMEGA and the National Ignition Facility (NIF), to support hydrodynamic scaling studies. These CH-shell experiments were designed to be hydrodynamically equivalent, spanning a factor of 40 in laser energy and a factor of 3.4 in spatial and temporal scales, while preserving the incident laser intensity of 10 15 W/cm 2 . Experiments with similarly low levels of beam smoothing on OMEGA and NIF show a similar fraction (~0.2%) of laser energy deposited as hot electron preheat in the unablated shell on both OMEGA and NIF and similar preheat per mass (~2 kJ/mg), despite the NIF experiments generating a factor of three more hot electrons (~1.5% of laser energy) than on OMEGA (~0.5% of laser energy). This is plausibly explained by more absorption of hot electron energy in the ablated CH plasma on NIF due to larger areal density, as well as a smaller solid angle of the imploding shell as viewed from the hot electron generating region due to the hot electrons being produced at a larger standoff distance in lower-density regions by stimulated Raman scattering, in contrast to in higher-density regions by two-plasmon decay on OMEGA. Finally, the results indicate that for warm implosions at intensities of around 10 15 W/cm 2 , hydrodynamic equivalence is not violated by hot electron preheat, though for cryogenic implosions, the reduced attenuation of hot electrons in deuterium–tritium plasma will have to be considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Understanding the fusion yield dependencies in OMEGA DT-layered implosion experiments using a physics-based statistical mapping model

Improving the performance of inertial confinement fusion implosions requires physics models that can accurately predict the response to changes in the experimental inputs. Good predictive capability has been demonstrated for the fusion yield using a statistical mapping of simulated outcomes to experimental data [Gopalaswamy et al., Nature 565(771), 581–586 (2019)]. In this paper, a physics-based statistical mapping approach is used to extract and quantify all the major sources of degradation of fusion yield for direct-drive implosions on the OMEGA laser. Here, the yield is found to be dependent on the age of the deuterium tritium fill, the ℓ = 1 asymmetry in the implosion core, the laser beam-to-target size ratio, and parameters related to the hydrodynamic stability. A controlled set of experiments were carried out where only the target fill age was varied while keeping all other parameters constant. The measurements were found to be in excellent agreement with the fill age dependency inferred using the mapping model. In addition, a new implosion design was created, guided by the statistical mapping model by optimizing the trade-offs between increased laser energy coupling at larger target size and the degradations caused by the laser beam-to-target size ratio and hydrodynamic instabilities. When experimentally performed, an increased fusion yield was demonstrated in targets with larger diameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Fuel–shell mix and yield degradation in kinetic shock-driven inertial confinement fusion implosions

Fuel–shell mix in kinetic plasma conditions is probed using nuclear and x-ray self-emission in shock-driven, D 3 He-gas-filled inertial confinement fusion implosions. As initial gas fill density decreases, measured nuclear yields and ion temperatures are lower than expected as compared to radiation-hydrodynamic simulations. Spatially and temporally resolved x-ray emissions indicate significant mixing at the fuel–shell interface in implosions with low initial gas fill density. In conclusion, this observed fuel–shell mix introduces a substantial amount of shell ions into the center of the implosion prior to and during shock flash and is the key mechanism needed in the kinetic-ion simulations to match experimental nuclear yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Inertial Confinement Fusion—Experimental Physics: Laser Drive

Laser-driven inertial confinement fusion creates a central hot-spot plasma by irradiating a spherical target containing a thermonuclear fuel layer of deuterium (D) and tritium (T) with temporally-shaped, high-intensity lasers or X rays. Inertial confinement fusion relies on the DT-fusion alpha particles depositing their energy in a hot-spot plasma, causing its temperature to rise sharply and a thermonuclear burn wave to propagate out through the surrounding cold, dense DT fuel, producing significantly more energy than was used to heat and compress the fuel. Alpha heating has been demonstrated and burning plasma (i.e., yield amplification due to alpha heating >3.5) is being explored with megajoule-scale lasers on the path to ignition (i.e., yield amplification due to alpha heating >20)

alpha particles↗