Engineering topics

Rehfield, L. W.

Publications and source records attributed to Rehfield, L. W..

8 records

NASA NTRS1988

An ideal clamping analysis for a cross-ply laminate

Different elementary clamping models are discussed for a three layer crossply laminate to study the sensitivity of clamping to the definition of cross-sectional rotation. All of these models leave a considerable residual warping at the edges. Using a complimentary energy principle and principle of superposition, an analysis is conducted to reduce this residual warping. This led to the identification of exact interior solution corresponding to the ideal clamping. This study also suggests a presence of stress singularities at the corners and between different layers near the fixed edge.

Valisetty, R. R.↗

NASA NTRS1987

Composite box beam analysis - Theory and experiments

Beam theory is widely used as a first approximation in numerous structural applications. When applied to composite beams, the accuracy of beam theory becomes questionable because (1) the shearing and warping deformations become significant, as the shearing stiffness of composite laminates is often very low, and (2) several elastic couplings can occur that strongly influence the behavior of composite beams. The torsional behavior of thin-walled composite beams has important implications for aeronautical structures and is deeply modified by the above nonclassical effects. This paper presents two comprehensive analysis methodologies for composite beams and describes experimental results obtained from a thin-walled, rectangular cross-sectional beam. The theoretical predictions are found in good agreement with the observed twist and strain distributions. Out-of-plane torsional warping of the cross-section is found to be the key factor for an accurate modeling of the torsional behavior of such structures.

Bauchau, O. A.↗

NASA NTRS1986

Some observations on the behavior of the Langley model rotor blade

The design of the model rotor and the comparative study of coupled beam theory and the finite element analysis performed earlier at the Aerostructures Directorate by Robert Hodges and Mark Nixon is examined. Attention is focused upon two matters: (1) an examination of the small discrepancies between twist angle predictions under pure torque and radial loading, and (2) an assessment of nonclassical effects in bending behavior. The primary objective is understanding, particularly with regard to cause and effect relationships. Understanding, together with the simple, affordable nature of the coupled beam analysis, provides a sound basis for design.

Rehfield, L. W.↗

NASA NTRS1986

Sublaminate analysis of interlaminar fracture in composites

A simple analysis method based upon a transverse shear deformation theory and a sublaminate approach is utilized to analyze a mixed-mode edge delamination specimen. The analysis provides closed form expressions for the interlaminar shear stresses ahead of the crack, the total energy release rate, and the energy release rate components. The parameters controlling the behavior are identified. The effect of specimen stacking sequence and delamination interface on the strain energy release rate components is investigated. Results are compared with a finite element simulation for reference. The simple nature of the method makes it suitable for preliminary design analyses which require a large number of configurations to be evaluated quickly and economically.

Armanios, E. A.↗

NASA NTRS1986

Interlaminar analysis of laminated composites using a sublaminate approach

A simple analysis method based upon a transverse shear deformation theory and a sublaminate approach is utilized to analyze a Mixed-Mode edge delamination specimen. The analysis provides a closed form distribution of the interlaminar shear stresses ahead of the crack, and the parameters controlling the behavior are identified. The effect of specimen stacking sequence and delamination interface on the strain energy release rate components is investigated. Results are compared with a finite element simulation for reference. The simple nature of the method makes it suitable for preliminary design analyses which require a large number of configurations to be evaluated quickly and economically.

Armanios, E. A.↗

NASA NTRS1985

A new ply model for interlaminar stress analysis

An accurate estimate of interlaminar stresses is crucial to understanding, as well as predicting, many delamination-related failures in composite materials. A new model for ply-level sublaminate analysis is presented and applied. The homogeneous plate theory developed earlier by the authors (Valisetty and Rehfield, 1983) is further refined, and the equations are reduced appropriately for the classical finite-width free-edge laminate elasticity problem and a related delamination crack growth problem. It is applied to the laminate on a ply-by-ply basis. This theory incorporates all the essential physical effects and appears to be an adequate model for predicting the behavior of individual layers in equilibrium. On the basis of the number of equations and boundary conditions required for the implementation of layer equilibrium, this theory also appears to be the simplest of its kind presented so far. The stress induced in the free-edge region of a (0,90,90,0) laminate in uniform extension and the energy release rates for the delamination between the -30 deg and 90 deg plies of a (+, -30,+, -30, 90,90)s laminate are computed using the new analysis. The results are in excellent agreement with the existing numerical solutions. The new ply behavioral model appears to be very promising; it yields stresses and displacements that are statically and kinematically compatible at interlaminar surfaces.

Rao Valisetty, R.↗

NASA NTRS1984

Simple theoretical models for composite rotor blades

The development of theoretical rotor blade structural models for designs based upon composite construction is discussed. Care was exercised to include a member of nonclassical effects that previous experience indicated would be potentially important to account for. A model, representative of the size of a main rotor blade, is analyzed in order to assess the importance of various influences. The findings of this model study suggest that for the slenderness and closed cell construction considered, the refinements are of little importance and a classical type theory is adequate. The potential of elastic tailoring is dramatically demonstrated, so the generality of arbitrary ply layup in the cell wall is needed to exploit this opportunity.

Valisetty, R. R.↗

NASA NTRS1973

Design of stiffened cylinders to resist axial compression.

A design procedure is presented for compressed cylindrical shells stiffened by stringers and rings. The approach is indirect and begins by considering the applied stress level as a primary design variable. A new method for the sizing and spacing of rings is outlined and illustrated. Emphasis is placed upon the achievement of a minimum weight design within practical constraints imposed by parameter values.

Rehfield, L. W.↗