Engineering topics

Reich, Carey

Publications and source records attributed to Reich, Carey.

4 records

DOE OSTI2024

As‐Doped Polycrystalline CdSeTe: Localized Defects, Carrier Mobility and Lifetimes, and Impact on High‐Efficiency Solar Cells

Abstract The efficiency potential for single‐junction photovoltaics (PV) is described by the detailed balance model, which requires the elimination of nonradiative recombination and perfect minority carrier collection. Improvements in GaAs, Si, and perovskite PV follow this model. It might be more complex for CdTe, a leading thin‐film PV technology. While lifetime, passivation, and doping goals for 25% efficient CdTe solar cells are largely reached, voltage is ≈20% below the detailed balance limit. Why is that? In Se‐alloyed CdSe x Te 1‐x (Se is required for >20% efficiency) additional losses can occur due to electrostatic and bandgap fluctuations and due to electronic trap states. To understand mechanisms limiting CdSeTe solar cell performance and to suggest improvements, carrier dynamics, and transport in CdSe x Te 1‐x with variation in Se composition and as doping is analyzed. It is shown that trapping, likely due to anion‐site defects and their complexes, is correlated with low charge carrier mobility of 0.1–0.6 cm 2 (Vs) −1 . Even with 1000 ns charge carrier lifetimes, carrier diffusion length is less than the absorber thickness, reducing efficiency to ≈23%. Device simulations are used to analyze the performance of CdSe x Te 1‐x solar cells; thermodynamic models are not sufficient for absorbers with electronic disorder and trapping.

14 SOLAR ENERGY↗

DOE OSTI2023

Why Increased CdSeTe Charge Carrier Lifetimes and Radiative Efficiencies did not Result in Voltage Boost for CdTe Solar Cells

After a focused effort over the last decade, order-of-magnitude improvements in doping and electro-optical characteristics (radiative efficiency, carrier lifetime, and passivation) have been reported for polycrystalline CdSeTe solar cells. Surprisingly, this did not result in higher solar cell voltages regardless of device contacting layers, absorber grading profiles, and other changes in device architecture. From detailed evaluation of radiative emission and carrier dynamics in CdSeTe heterostructures and devices, it is shown that the complexity introduced to the absorber to achieve lifetime and passivation metrics resulted in charge carrier trapping, which now negatively affects CdSeTe absorbers.

CdTe↗

DOE OSTI2023

A comprehensive material study of CdSeTe films deposited with differing selenium compositions

The addition of selenium into CdTe to create the ternary alloy CdSeTe has been one of the most impactful advancements to CdTe-based photovoltaics in the last decade. CdSeTe/CdTe bilayer device structures have enabled a gain in short-circuit current due to the narrower bandgap of the alloy, with minimal to no loss in voltage. Intensity of photoluminescence and time-resolved photoluminescence measurements suggest this is due to an increase in carrier lifetime and concomitant greater fraction of radiative vs non-radiative recombination events which allows for a reduction in the voltage deficit. Here, in this work, we study the properties of as-deposited and CdCl 2 -treated CdSeTe films deposited by close-space sublimation under varying conditions from CdSeTe source charges with both 20 and 40 mol% CdSe. We find that the selenium content in the deposited films are substantially reduced from that of the source material. Additionally, deposition temperature, particularly that of the substrate, considerably affects the grain size, crystallinity, and photoluminescence of the material, illustrating the importance of source material selection and process optimization. Finally, we present evidence that the source material, and therefore the properties of the deposited films, change over time as the source material is used.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation

Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.

cadmium telluride↗