Engineering topics

Reimerdes, H. (ORCID:0000000297261519)

Publications and source records attributed to Reimerdes, H. (ORCID:0000000297261519).

10 records

DOE OSTI2026

Systematic multi-machine analysis of the exhaust time-dependent behavior in tokamaks

The understanding of the time-scales and associated transient behavior of fusion exhaust plasmas plays a crucial role in its dynamic modeling and its control. This work presents an overview of experimental investigations of the exhaust dynamics in TCV, MAST-U, ASDEX-Upgrade, WEST, DIII-D, and JET. From the presented experiments, a clear picture arises on properties of the exhaust dynamics across machines. Particularly, we observe that the scrape-off layer equilibrates on fast time-scales ($>$ 70 Hz) and that exhaust dynamics measured in response to gas valve modulations mostly behave smoothly and linearly, with similarities across devices, across scenarios (H-mode, L-mode), injected species, and injection locations. The measurements presented have formed the basis for systematic exhaust control on the considered devices. We now present this database for the essential validation of dynamic exhaust models for reactor design and control.

control↗

DOE OSTI2025

Demonstration of Super-X divertor exhaust control for transient heat load management in compact fusion reactors

Nuclear fusion could offer clean, abundant energy. However, managing the power exhausted from the core fusion plasma towards the reactor wall remains a major challenge. This is compounded in emerging compact reactor designs promising more cost-effective pathways towards commercial fusion energy. Alternative Divertor Configurations (ADCs) are a potential solution. In this work, we demonstrate exhaust control in ADCs, employing a novel method to diagnose the neutral gas buffer, which shields the target. Our work on the Mega Ampere Spherical Tokamak Upgrade shows that ADCs tackle key risks and uncertainties for fusion energy. Their highly reduced sensitivity to perturbations enables active exhaust control in otherwise unfeasible situations and facilitates an increased passive absorption of transients, which would otherwise damage the divertor. We observe a strong decoupling of each divertor from other reactor regions, enabling near-independent control of the divertors and core plasma. Our work showcases the real-world benefits of ADCs for effective heat load management in fusion power reactors.

Imaging techniques↗

DOE OSTI2025

MHD, disruptions and control physics: Chapter 4 of the special issue: on the path to tokamak burning plasma operation

In this chapter, we review the progress in MHD stability, disruptions and control in magnetic fusion research that has occurred over the past (more than) one and a half decades since the publication by Hender et al in 2007 on the same topic as part of the update of ITER Physics Basis. During this period, remarkable progress has been achieved in the understanding of the basic physics and overall control of MHD instabilities through a wide spectrum of dedicated experiments, theory and modeling. The sawtooth activities are probably today one of the best understood of MHD events and very robust control schemes have been developed for reliable operation of tokamaks through core heating. Similarly, significant improvements have been achieved in understanding and control of neoclassical tearing modes, resistive wall modes or locked modes and their control through ECCD or error field control. The field of disruption prediction through application of artificial intelligence, machine learning or deep learning methods, which had already started at the time of the 2007 review, has progressed significantly due to general progress in these fields and application of newer, more sophisticated algorithms. However, although remarkable progress has been achieved in the field of Disruptions, their understanding, prediction, possible avoidance and mitigation still remain probably the most active fields of R&D globally in this field. This is especially because reactor grade machines like ITER and DEMO will be much less tolerant in respect of disruptions and runaway currents, and their occurrences must be either avoided altogether or minimized to an acceptable value without causing any significant hindrance to robust machine operations. This review is intended to present a broad spectrum of the R&D that has occurred in this field in support of ITER, which will also be of immense significance for all future machines, especially reactors like DEMO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

An upper pressure limit for low- Z benign termination of runaway electron beams in TCV

Abstract We present a model for the particle balance in the post-disruption runaway electron plateau phase of a tokamak discharge. The model is constructed with the help of, and applied to, experimental data from TCV discharges investigating the so-called ‘low- Z benign termination’ runaway electron mitigation scheme. In the benign termination scheme, the free electron density is first reduced in order for a subsequently induced MHD instability to grow rapidly and spread the runaway electrons widely across the wall. We show that the observed non-monotonic dependence of the free electron density with the measured neutral pressure is due to plasma re-ionization induced by runaway electron impact ionization. At higher neutral pressures, more target particles are present in the plasma for runaway electrons to collide with and ionize. Parameter scans are conducted to clarify the role of the runaway electron density and energy on the free electron density, and it is found that only the runaway electron density has a noticeable impact. While the free electron density is shown to be related to the spread of heat fluxes at termination, the exact cause for the upper neutral pressure limit remains undetermined and an object for further study.

Hoppe, M. (ORCID:0000000339948977)↗

DOE OSTI2024

Comparison of detachment in Ohmic plasmas with positive and negative triangularity

Abstract In recent years, negative triangularity (NT) has emerged as a potential high-confinement L-mode reactor solution. In this work, detachment is investigated using core density ramps in lower single null Ohmic L-mode plasmas across a wide range of upper, lower, and average triangularity (the mean of upper and lower triangularity: δ ) in the TCV tokamak. It is universally found that detachment is more difficult to access for NT shaping. The outer divertor leg of discharges with δ ≈ − 0.3 could not be cooled to below 5 eV through core density ramps alone. The behavior of the upstream plasma and geometrical divertor effects (e.g. a reduced connection length with negative lower triangularity) do not fully explain the challenges in detaching NT plasmas. Langmuir probe measurements of the target heat flux widths ( λ q ) were constant to within 30% across an upper triangularity scan, while the spreading factor S was lower by up to 50% for NT, indicating a generally lower integral scrape-off layer width, λ int . The line-averaged core density was typically higher for NT discharges for a given fuelling rate, possibly linked to higher particle confinement in NT. Conversely, the divertor neutral pressure and integrated particle fluxes to the targets were typically lower for the same line-averaged density, indicating that NT configurations may be closer to the sheath-limited regime than their PT counterparts, which may explain why NT is more challenging to detach.

Physics↗

DOE OSTI2024

The effect of plasma shaping on high density H-mode SOL profiles and fluctuations in TCV

Abstract The impact of plasma shaping on the properties of high density H-mode scrape-off layer (SOL) profiles and transport at the outer midplane has been investigated on Tokamakà configuration variable. The experimental dataset has been acquired by evolving the upper triangularity while keeping the other parameters constant. The scan comprises δ u p values between 0.0 and 0.6, excluding negative triangularity scenarios. Within this study, a transition from type-I edge localised modes to the quasi-continuous exhaust regime takes place from low to high δ u p . The modification of the upstream SOL profiles has been assessed, in terms of separatrix quantities, within the α t turbulence control parameter theoretical framework (Eich et al 2020 Nucl. Fusion 60 056016). The target parallel heat load and the upstream near-SOL density profiles have been shown to broaden significantly for increasing α t . Correspondingly, in the far SOL a density shoulder formation is observed when moving from low to high δ u p . These behaviours have been correlated with an enhancement of the SOL fluctuation level, as registered by wall-mounted Langmuir probes as well as the thermal helium beam diagnostic. Specifically, both the background and the filamentary-induced fluctuating parts of the first wall ion saturation current signal are larger at higher δ u p , with filaments being ejected more frequently into the SOL. Comparison of two pulses at the extremes of the δ u p scan range, but with otherwise same input parameters, shows that the midplane neutral pressure does not change much during the H-mode phase of the discharge. This indicates that indirect effects of the change in geometry, linked to first wall recycling sources, should not play a significant role. The total core radiation increases at high δ u p , on account of a stronger plasma–wall interaction and resulting larger carbon impurity intake from the first wall. This is likely associated to the enhanced first wall fluctuations, as well as a smaller outer gap and the close-to-double-null magnetic topology at high shaping.

Stagni, A. (ORCID:0000000180841544)↗

DOE OSTI2023

Validation of 2D Te and ne measurements made with Helium imaging spectroscopy in the volume of the TCV divertor

Abstract Multi-spectral imaging of helium atomic emission (HeMSI) has been used to create 2D poloidal maps of T e and n e in TCV’s divertor. To achieve these measurements, TCV’s MANTIS multispectral cameras (Perek et al 2019 Rev. Sci. Instrum. 90 123514) simultaneously imaged four He I lines (two singlet and two triplet) and a He II line (468 nm) from passively present He and He + . The images, which were absolutely calibrated and covered the whole divertor region, were inverted through the assumption of toroidal symmetry to create emissivity profiles and, consequently, line-ratio profiles. A collisional-radiative model (CRM) was applied to the line-ratio profiles to produce 2D poloidal maps of T e and n e . The collisional-radiative modeling was accomplished with the Goto helium CRM code (Zholobenko et al 2018 Nucl. Fusion 58 126006, Zholobenko et al 2018 Technical Report , Goto 2003 J. Quant. Spectrosc. Radiat. Transfer 76 331–44) which accounts for electron-impact excitation (EIE) and deexcitation, and electron–ion recombination (EIR) with He + . The HeMSI T e and n e measurements were compared with co-local Thomson scattering measurements. The two sets of measurements exhibited good agreement for ionizing plasmas: ( 5 eV ⩽ T e ⩽ 60 eV , and 2 × 10 18 m − 3 ⩽ n e ⩽ 3 × 10 19 m − 3 ) in the case of majority helium plasmas, and ( 10 eV ⩽ T e ⩽ 40 eV , 2 × 10 18 m − 3 ⩽ n e ⩽ 3 × 10 19 m − 3 ) in the case of majority deuterium plasmas. However, there were instances where HeMSI measurements diverged from Thomson scattering. When T e ⩽ 10 eV in majority deuterium plasmas, HeMSI deduced inaccurately high values of T e . This disagreement cannot be rectified within the CRM’s EIE and EIR framework. Second, on sporadic occasions within the private flux region, HeMSI produced erroneously high measurements of n e . Multi-spectral imaging of Helium emission has been demonstrated to produce accurate 2D poloidal maps of T e and n e within the divertor of a tokamak for plasma conditions relevant to contemporary divertor studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

New insights on divertor parallel flows,E × B drifts, and fluctuations from in situ, two-dimensional probe measurement in the Tokamak à Configuration Variable

Abstract In situ , two-dimensional (2D) Langmuir probe measurements across a large part of the TCV outer divertor are reported in L-mode discharges with and without divertor baffles. This provides detailed insights into time averaged profiles, particle fluxes, and fluctuation behavior in different divertor regimes. The presence of the baffles is shown to substantially increase the divertor neutral pressure for a given upstream density and to facilitate the access to detachment, an effect that increases with plasma current. The detailed, 2D probe measurements allow for a divertor particle balance, including ion flux contributions from parallel flows and E × B drifts. The poloidal flux contribution from the latter is often comparable or even larger than the former, and the divertor parallel flow direction reverses in some conditions, pointing away from the target. In most conditions, the integrated particle flux at the outer target can be predominantly ascribed to ionization along the outer divertor leg, consistent with a closed-box approximation of the divertor. The exception is a strongly detached divertor, achieved here only with baffles, where the total poloidal ion flux even decreases towards the outer target, indicative of significant plasma recombination. The most striking observation from relative density fluctuation measurements along the outer divertor leg is the transition from poloidally uniform fluctuation levels in attached conditions to fluctuations strongly peaking near the X-point when approaching detachment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Validation of edge turbulence codes against the TCV-X21 diverted L-mode reference case

Self-consistent full-size turbulent-transport simulations of the divertor and scrape-off-layer (SOL) of existing tokamaks have recently become feasible. This enables the direct comparison of turbulence simulations against experimental measurements. In this work, we perform a series of diverted ohmic L-mode discharges on the tokamak à configuration variable (TCV) tokamak, building a first-of-a-kind dataset for the validation of edge turbulence models. This dataset, referred to as TCV-X21, contains measurements from five diagnostic systems from the outboard midplane (OMP) to the divertor targets—giving a total of 45 one- and two-dimensional comparison observables in two toroidal magnetic field directions. The experimental dataset is used to validate three flux-driven 3D fluid-turbulence models—GBS, GRILLIX and TOKAM3X. With each model, we perform simulations of the TCV-X21 scenario, individually tuning the particle and power source rates to achieve a reasonable match of the upstream separatrix value of density and electron temperature. We find that the simulations match the experimental profiles for most observables at the OMP—both in terms of profile shape and absolute magnitude—while a comparatively poorer agreement is found towards the divertor targets. The match between simulation and experiment is seen to be sensitive to the value of the resistivity, the heat conductivities, the power injection rate and the choice of sheath boundary conditions. Additionally, despite targeting a sheath-limited regime, the discrepancy between simulations and experiment also suggests that the neutral dynamics should be included. The results of this validation show that turbulence models are able to perform simulations of existing devices and achieve reasonable agreement with experimental measurements. Where disagreement is found, the validation helps to identify how the models can be improved. By publicly releasing the experimental dataset and validation analysis, this work should help to guide and accelerate the development of predictive turbulence simulations of the edge and SOL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Theory-based scaling laws of near and far scrape-off layer widths in single-null L-mode discharges

Abstract Theory-based scaling laws of the near and far scrape-off layer (SOL) widths are analytically derived for L-mode diverted tokamak discharges by using a two-fluid model. The near SOL pressure and density decay lengths are obtained by leveraging a balance among the power source, perpendicular turbulent transport across the separatrix, and parallel losses at the vessel wall, while the far SOL pressure and density decay lengths are derived by using a model of intermittent transport mediated by filaments. The analytical estimates of the pressure decay length in the near SOL is then compared to the results of three-dimensional, flux-driven, global, two-fluid turbulence simulations of L-mode diverted tokamak plasmas, and validated against experimental measurements taken from an experimental multi-machine database of divertor heat flux profiles, showing in both cases a very good agreement. Analogously, the theoretical scaling law for the pressure decay length in the far SOL is compared to simulation results and to experimental measurements in TCV L-mode discharges, pointing out the need of a large multi-machine database for the far SOL decay lengths.

Physics↗