Engineering topics

Reinke, Matthew L.

Publications and source records attributed to Reinke, Matthew L..

5 records

DOE OSTI2024

Evaluation of SPARC divertor conditions in H-mode operation using SOLPS-ITER

The predicted divertor conditions for the SPARC tokamak are calculated using SOLPS-ITER for a range of scrape-off-layer (SOL) heat flux widths λ q , input powers, and particle fueling locations. Under H-mode scenario conditions with an upstream separatrix density of 1 x 10 20 m -3 , the most conservative range of λ q extrapolations ( 0.15 mm) results in extremely high unmitigated particle and energy fluxes to the divertor, both under full field (12.2 T) and power (P SOL = 29 MW) conditions, and 2/3 field with P SOL = 10 MW. Increasing the cross-field SOL diffusivities by 2–10× reduces the magnitude of the mitigation challenge, however strategies such as impurity seeding or strike-point-sweeping will likely still be required. A combination of steady-state and time-dependent SOLPS-ITER simulations are used to map out phase space diagrams of upstream and divertor conditions. The simulations include parallel currents but neglect cross-field drifts. At low upstream density the inner and outer divertor conditions are highly asymmetric, with a large temperature difference and significant heat fluxes driven by parallel currents. The solution has sharp bifurcations with a region of hysteresis, depending on whether the initial state is at a low or high density. This behavior is observed even when the fueling location, cross-field diffusivity, and impurity level is changed, although the density window with asymmetry is reduced with increasing diffusivity. The addition of neon impurity seeding reduces the divertor heat fluxes, but also causes a drop in the upstream electron density with fixed particle throughput. This drop can be counteracted by increased main ion throughput, however too much neon results in a back transition into the asymmetric divertor regimes suggesting a need for control of both main ion and impurity seeding levels to achieve a desired divertor state.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Design and implementation of a prototype infrared video bolometer (IRVB) in MAST Upgrade

A prototype infrared video bolometer (IRVB) was successfully deployed in the Mega Ampere Spherical Tokamak Upgrade (MAST Upgrade or MAST-U), the first deployment of such a diagnostic in a spherical tokamak. The IRVB was designed to study the radiation around the lower x-point, another first in tokamaks, and has the potential to estimate emissivity profiles with spatial resolution beyond what is achievable with resistive bolometry. The system was fully characterized prior to installation on MAST-U, and the results are summarized here. After installation, it was verified that the actual measurement geometry in the tokamak qualitatively matches the design; this is a particularly difficult process for bolometers and was done using specific features of the plasma itself. The installed IRVB measurements are consistent both with observations from other diagnostics, including magnetic reconstruction, visible light cameras, and resistive bolometry, as well as with the IRVB-designed view. Early results show that with conventional divertor geometry and only intrinsic impurities (for example, C and He), the progression of radiative detachment follows a similar path to that observed for large aspect ratio tokamaks: The peak of the radiation moves along the separatrix from the targets to the x-point and high-field side midplane with a toroidally symmetric structure that can eventually lead to strong effects on the core plasma inside the separatrix.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Multichannel Fiber-Optic Silicon Fabry–Pérot Interferometric Bolometer System for Plasma Radiation Measurements

A single-channel fiber-optic bolometer system based on a high-finesse silicon Fabry–Pérot interferometer (FPI) was previously reported, intended to measure plasma radiation from the magnetically confined fusion chamber. Recently, we developed a multichannel fiber-optic bolometer system with five bolometers multiplexed using a coarse wavelength division multiplexer (CWDM) and interrogated with a white-light system involving a superluminescent light-emission diode source and a high-speed spectrometer. One of the bolometers was used as the reference bolometer to compensate for the ambient temperature variations, and the other four bolometers were used for radiation measurement. The bolometers have a simple structure with a silicon pillar at the end of the single-mode fiber and a gold disk on the other side of the silicon pillar. They are also easy to fabricate without stringent requirements on the optical alignment. Analysis of the system optimization was performed to improve the noise performance and to mitigate the vibration effect that may present in the practical application. The system had a significantly enhanced measurement range compared to the previous high-finesse FPI bolometer system for measuring radiation. Test results performed in air using a 405 nm laser as the radiation source showed that the temperature resolution and the noise-equivalent power density of the sensing bolometers connected to each channel of the CWDM were, respectively, ~0.4 mK and ~0.1 W/m2, with a time constant of ~220 ms, which is comparable to the previous more complicated fiber-optic bolometer systems based on high-finesse FPIs that were interrogated using wavelength-scanning lasers.

Uddin, Nezam↗

DOE OSTI2021

Parameter dependencies of the experimental nitrogen concentration required for detachment on ASDEX Upgrade and JET

While current tokamak experiments are beginning to use real-time feedback control systems to manage the plasma exhaust, future tokamaks still require validation of theoretical models used to predict the threshold impurity concentration required to sufficiently reduce the power and particle fluxes to the divertor. This work exploits new spectroscopic measurements of the divertor nitrogen concentration, c n , in partially detached N 2 -seeded H-mode plasmas on ASDEX Upgrade (AUG) and JET with the ITER-Like Wall (JET-ILW) to test the parameter dependencies of the power flowing to the outer divertor, P div,outer , and the separatrix electron density, n e.sep . A least-squares regression of the AUG measurements demonstrates that the threshold c n required for detachment scales as $c_n∝P^{1.19±0.32}_{div,outer}n^{-2.77±0.36}_{e,sep}$. This scaling of n e,sep is also consistent with the measurements from JET which, at constant P div,outer , show $c_n∝n^{-2.43±0.27}_{e,sep}$. The dependencies of P div,outer and n e.sep is demonstrated over at least a factor of two change in both parameters and indicates a stronger dependence on n e.sep in comparison to the Lengyel model, which could be due to the assumption in this model that the heat flux channel width is independent of density. This first assessment of detachment scaling with impurity seeding highlights the need for further analysis of the systematic uncertainties of the measurement and more consistent scenarios from more tokamaks to investigate the machine size scaling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Fiber-Optic Silicon Fabry-Perot Interferometric Bolometer: The Influence of Mechanical Vibration and Magnetic Field

Plasma radiation plays an important role in the operation and control of magnetic confinement fusion and is typically measured by bolometers. Here, we study the influence of mechanical vibration and magnetic field, which are typically present in magnetic confinement fusion devices, on the performance of a fiber-optic bolometer (FOB) based on silicon Fabry-Perot interferometer (FPI) demodulated by a scanning diode laser. It is found that both the vibration and magnetic field could cause large noise due to the birefringence of the silicon FPI. To mitigate the birefringence effects, we demonstrated two effective methods: polarization maintaining FOB and polarization scrambling. We show that two methods can be effective in mitigating the effect caused by the sensor birefringence: (1) replacing the regular single-mode fiber in the FOB system with polarization-maintaining fiber and (2) using a polarization scrambler after the laser source. For both methods, no significant increase in the noise was observed in the vibration and magnetic field tests. Finally, our research highlights the importance of the polarization management for the FOB systems toward their practical applications in magnetic-confinement fusion systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗