Engineering topics

Ren, Dan

Publications and source records attributed to Ren, Dan.

6 records

DOE OSTI2022

A universal co-solvent dilution strategy enables facile and cost-effective fabrication of perovskite photovoltaics

Cost management and toxic waste generation are two key issues that must be addressed before the commercialization of perovskite optoelectronic devices. We report a groundbreaking strategy for eco-friendly and cost-effective fabrication of highly efficient perovskite solar cells. This strategy involves the usage of a high volatility co-solvent, which dilutes perovskite precursors to a lower concentration (<0.5 M) while retaining similar film quality and device performance as a high concentration (>1.4 M) solution. More than 70% of toxic waste and material cost can be reduced. Mechanistic insights reveal ultra-rapid evaporation of the co-solvent together with beneficial alteration of the precursor colloidal chemistry upon dilution with co-solvent, which in-situ studies and theoretical simulations confirm. The co-solvent tuned precursor colloidal properties also contribute to the enhancement of the stability of precursor solution, which extends its processing window thus minimizing the waste. This strategy is universally successful across different perovskite compositions, and scales from small devices to large-scale modules using industrial spin-coating, potentially easing the lab-to-fab translation of perovskite technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA‐Free, Phase‐Pure, and Stable α‐Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

Abstract α‐Formamidinium lead iodide (α‐FAPbI 3 ) is one of the most promising candidate materials for high‐efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of α‐FAPbI 3 where both the composition and the phase are pure is very challenging. Herein, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)‐free and phase‐pure stable α‐FAPbI 3 films. The incorporation of volatile FA‐based additives in the precursor solutions completely suppresses the formation of non‐perovskite δ‐FAPbI 3 during film crystallization. Grains of the desired α‐phase are anchored together and stabilized when 4‐ tert ‐butylbenzylammonium iodide is permeated into the α‐FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21 % for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ≈90 % of their initial efficiency after storage at 50 °C for over 1600 hours.

Ling, Xufeng↗

DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA-Free, Phase-Pure, and Stable α-Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

a-Formamidinium lead iodide (a-FAPbI 3 ) is one of the most promising candidate materials for high-efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of a-FAPbI 3 where both the composition and the phase are pure is very challenging. In this work, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)-free and phase-pure stable a-FAPbI 3 films. The incorporation of volatile FA-based additives in the precursor solutions completely suppresses the formation of non-perovskite d-FAPbI 3 during film crystallization. Grains of the desired a-phase are anchored together and stabilized when 4-tert-butylbenzylammonium iodide is permeated into the a-FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21% for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ~90 % of their initial efficiency after storage at 50 degrees C for over 1600 hours.

14 SOLAR ENERGY↗

DOE OSTI2021

Gold-in-copper at low *CO coverage enables efficient electromethanation of CO 2

The renewable-electricity-powered CO 2 electroreduction reaction provides a promising means to store intermittent renewable energy in the form of valuable chemicals and dispatchable fuels. Renewable methane produced using CO 2 electroreduction attracts interest due to the established global distribution network; however, present-day efficiencies and activities remain below those required for practical application. Here we exploit the fact that the suppression of *CO dimerization and hydrogen evolution promotes methane selectivity: we reason that the introduction of Au in Cu favors *CO protonation vs. C-C coupling under low *CO coverage and weakens the *H adsorption energy of the surface, leading to a reduction in hydrogen evolution. We construct experimentally a suite of Au-Cu catalysts and control *CO availability by regulating CO 2 concentration and reaction rate. This strategy leads to a 1.6× improvement in the methane:H 2 selectivity ratio compared to the best prior reports operating above 100 mA cm -2 . We as a result achieve a CO 2 -to-methane Faradaic efficiency (FE) of (56 ± 2)% at a production rate of (112 ± 4) mA cm -2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Silica-copper catalyst interfaces enable carbon-carbon coupling towards ethylene electrosynthesis

Membrane electrode assembly (MEA) electrolyzers offer a means to scale up CO 2 -to-ethylene electroconversion using renewable electricity and close the anthropogenic carbon cycle. To date, excessive CO 2 coverage at the catalyst surface with limited active sites in MEA systems interferes with the carbon-carbon coupling reaction, diminishing ethylene production. With the aid of density functional theory calculations and spectroscopic analysis, here we report an oxide modulation strategy in which we introduce silica on Cu to create active Cu-SiO x interface sites, decreasing the formation energies of OCOH* and OCCOH*—key intermediates along the pathway to ethylene formation. We then synthesize the Cu-SiO x catalysts using one-pot coprecipitation and integrate the catalyst in a MEA electrolyzer. By tuning the CO 2 concentration, the Cu-SiO x catalyst based MEA electrolyzer shows high ethylene Faradaic efficiencies of up to 65% at high ethylene current densities of up to 215 mA cm -2 ; and features sustained operation over 50 h.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Crown Ether Modulation Enables over 23% Efficient Formamidinium-Based Perovskite Solar Cells

The use of molecular modulators to reduce the defect density at the surface and grain boundaries of perovskite materials has been demonstrated to be an effective approach to enhance the photovoltaic performance and device stability of perovskite solar cells. Herein, we employ crown ethers to modulate perovskite films, affording passivation of undercoordinated surface defects. This interaction has been elucidated by solid-state nuclear magnetic resonance and density functional theory calculations. The crown ether hosts induce the formation of host-guest complexes on the surface of the perovskite films, which reduces the concentration of surface electronic defects and suppresses nonradiative recombination by 40%, while minimizing moisture permeation. As a result, we achieved substantially improved photovoltaic performance with power conversion efficiencies exceeding 23%, accompanied by enhanced stability under ambient and operational conditions. This work opens a new avenue to improve the performance and stability of perovskite-based optoelectronic devices through supramolecular chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗