Search NASA⌕ Search

Engineering topics

Ren, J.

Publications and source records attributed to Ren, J..

At least 37 records · Page 2

Improved core-edge compatibility using impurity seeding in the small angle slot (SAS) divertor at DIII-D

Impurity seeding studies in the slot divertor (SAS) at DIII-D have revealed a strong relationship between the detachment onset and pedestal characteristics with both target geometry and impurity species. N 2 seeding in the slot has led to the first simultaneous observation of detachment on the entire suite of boundary diagnostics viewing the SAS without degradation of core confinement. SOLPS-ITER simulations with D+C+N, full cross-field drifts and n-n collisions activated are performed for the first time in DIII-D to interpret the behavior. This illustrates a strong effect of divertor configuration and plasma drifts on the recycling source distribution with significant consequences on plasma flows. Flow reversal is found for both main ions and impurities affecting strongly the impurity transport and providing an explanation for the observed dependence on strike point location of the detachment onset and impurity leakage found in the experiments. Matched discharges with either nitrogen or neon injection show that while nitrogen does not significantly affect the pedestal, neon leads to increased pedestal pressure gradient and improved pedestal stability. Little nitrogen penetrates in the core, but a great amount of neon is found in the pedestal consistent with the different ionization potentials of the two impurities. This research demonstrates that neutral and impurity distributions in the divertor can be controlled through variations in strike point locations in a fixed baffle structure. Divertor geometry combined with impurity seeding enables mitigated divertor heat flux balancing core contamination and thus leading to enhanced divertor dissipation and improved core-edge compatibility which are essential for ITER and for future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of leakage neutron spectra for zirconium with D-T neutrons and validation of evaluated nuclear data

Integral neutronics experiments have been a powerful tool and method for examining the reliability of evaluated nuclear data. In the present paper, the accuracy of evaluated nuclear data for Zirconium has been validated by comparing measured leakage neutron spectra with calculated ones. Leakage neutron spectra from the irradiation of D-T neutrons on Zirconium samples were experimentally measured at 60° and 120° by using a time-of-flight method. Theoretical calculations are carried out by Monte Carlo neutron transport code MCNP-4C with evaluated nuclear data of the ENDF/B-VII.0, ENDF/B-VIII.0, JENDL-4.0 and CENDL-3.1 libraries. From the comparisons, it is found that the calculations with JENDL-4.0 gives better agreements with the experiments at 60° while a large discrepancies are observed in the 4–13.5 MeV energy range at 120°. However, the calculated spectra using the data from ENDF/B-VII.0, ENDF/B-VIII.0 and CENDL-3.1 libraries showed some discrepancies with the measured ones, especially caused by the difference of the elastic and inelastic angular distributions and the secondary neutron energy distributions in the continuum inelastic scattering.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

First experimental tests of a new small angle slot divertor on DIII-D

A new small angle slot (SAS) divertor concept has been developed to enhance neutral cooling across the divertor target by coupling a closed slot structure with appropriate target shaping. Initial tests on DIII-D find a strong interplay between such anticipated ‘SAS’ effects and cross-field drifts, favouring operation with the ion B×∇B drift away from the X-point, as currently employed for advanced tokamaks. This offers the following key improvements relative to DIII-D’s open lower divertor or partially-closed upper divertor: (i) SAS allows for transition to low temperature moderately detached divertor conditions with T_e≲10eV at very low main plasma densities, lower than are usually attainable at all in DIII-D high confinement (H-mode) plasmas as used in these tests; (ii) Pedestal performance and core confinement are significantly improved with SAS. The final confinement collapse associated with the onset of X-point MARFE (multifaceted asymmetric radiation from the edge) following deep detachment occurs at significantly higher pedestal densities, thus widening the window of H-mode operation compatible with a dissipative divertor. For operation with the ion B×∇B drift toward the X-point, the divertor plasma transitions to a bifurcative detached state at much higher densities, similar to other divertor configurations in DIII-D. These results highlight the strong interplay between divertor closure and drifts, and point to an interesting divertor optimization path to explore that offers potential for future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Possible Origin of Ferromagnetism in Transition Metal Doped Zirconia

We have studied the electronic structure and magnetic properties of cubic zirconia (c-ZrO{sub 2}) with cobalt (Co) or nickel (Ni) doping using density functional theory (DFT) calculations. The pure c-ZrO{sub 2} is a nonmagnetic insulator with a wide bandgap. The calculated results reveal that isolated Co or Ni atom can both produce the local magnetic moment in c-ZrO{sub 2}. And the isolated Co atom can introduce a magnetic moment of about 0.98 μ{sub B}, while the Ni atom is 2.85 μ{sub B}. The impurity peaks can be formed in the bandgap. Our studies show that the magnetic moments mainly result from d orbitals of the impurity atoms. And the spin-up electrons will be arranged in t{sub 2g} orbitals under the ligand field of O{sub h} group in Co- or Ni-doped c-ZrO{sub 2}. Obviously, this will lead to a high-spin state (S = 1/2 or 1). The studies of magnetic coupling reveal that the two Co atoms in c-ZrO{sub 2} are not always coupled ferromagnetically at different distances. And the system will be in a spin singlet state (S = 0) when the distance is 6.209 or 7.170 Å between two Co atoms. However, the two Ni atoms in c-ZrO{sub 2} are always coupled ferromagnetically at all distances. So we can conclude that the Ni-doped c-ZrO{sub 2} is more suitable for spintronic material than Co doping. These results are significant for spintronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetism in Boron Nitride Monolayer Induced by Cobalt or Nickel Doping

We have investigated the electronic structure and magnetic properties of cobalt (Co)- or nickel (Ni)-doped hexagonal boron nitride (h-BN) monolayer using density functional theory calculations. The h-BN monolayer without any doping is a nonmagnetic insulator. Our studies show that isolated Co or Ni atom can both induce the local magnetic state in h-BN monolayer. And the impurity energy levels will be formed in the band gap. Results of our first-principle calculations reveal that isolated Co atom can result in a magnetic moment of 3.57 μ{sub B}, while the Ni atom is 0.87 μ{sub B}. And the magnetic moments mainly come from d orbitals of the doped atoms. The studies of magnetic coupling show that the two Co atoms at different distances in h-BN monolayer do not always couple ferromagnetically. When the distances are 2.504 and 6.625 Å, the spins induced by the two Co atoms will form antiferromagnetic ground states. While the two Ni atoms at different distances in the monolayer always couple ferromagnetically. So our results imply that the Ni-doped h-BN is more suitable for spintronic material than Co doping. These results are useful for spintronic application.

74 ATOMIC AND MOLECULAR PHYSICS↗

Mitigation of plasma–material interactions via passive Li efflux from the surface of a flowing liquid lithium limiter in EAST

Here, a new flowing liquid Li limiter (FLiLi) based on the concept of a thin flowing film has been successfully designed and tested in the EAST device in 2014. A bright Li radiative mantle at the plasma edge was observed during discharges using FLiLi, resulting from passive Li injection and transport in the scrape-off layer (SOL) plasma. Li particle efflux from the FLiLi surface into the plasma was estimated at >5 × 10 20 atom s –1 , due to surface evaporation and sputtering, and accompanied with a few small Li droplets ~1 mm diameter that were ejected from FLiLi. The Li efflux from FLiLi was ionized by the SOL plasma and formed a Li radiation band that originated from the FLiLi surface, and then spread toroidally by SOL plasma flow. The Li radiative mantle appeared to partly isolate the plasma from the wall, reducing impurity release from the wall materials, and possibly leading to a modest improvement in confinement. In addition, strong Li radiation reduced the particle and heat fluxes impacting onto the divertor plate, with certain similarities to heat flux reduction and detachment onset via low-Z impurity injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Realizing the Potential of Micro-Phase Separated Block Copolymer Electrolytes: Ion Domain Connectivity Plays a Prominent Role in Ion Conduction

Block copolymer electrolytes (BCEs) offer the prospect of membranes with high ionic conductivity at lower ion-exchange capacities leading to membranes with robust mechanical properties. However, the microphase separated structure of such BCE membranes and its impact on membrane conductivity is poorly understood. Most studies assume that aggregated ionic domains in microphase separated BCEs, or random copolymers, is sufficient to foster facile ion conductivity. However, microphase separation alone cannot spur rapid ion conduction. In this paper, we demonstrate that ion domain connectivity greatly influences ion conductivity in BCEs. The results emphasize the importance of maximizing ion domain connectivity while minimizing terminal defects to realize BCEs with optimal ion transport properties.

36 MATERIALS SCIENCE↗

A phosphatidylinositol transfer protein integrates phosphoinositide signaling with lipid droplet metabolism to regulate a developmental program of nutrient stress-induced membrane biogenesis

Lipid droplet (LD) utilization is an important cellular activity that regulates energy balance and release of lipid second messengers. Because fatty acids exhibit both beneficial and toxic properties, their release from LDs must be controlled. Here we demonstrate that yeast Sfh3, an unusual Sec14-like phosphatidylinositol transfer protein, is an LD-associated protein that inhibits lipid mobilization from these particles. We further document a complex biochemical diversification of LDs during sporulation in which Sfh3 and select other LD proteins redistribute into discrete LD subpopulations. The data show that Sfh3 modulates the efficiency with which a neutral lipid hydrolase-rich LD subclass is consumed during biogenesis of specialized membrane envelopes that package replicated haploid meiotic genomes. These results present novel insights into the interface between phosphoinositide signaling and developmental regulation of LD metabolism and unveil meiosis-specific aspects of Sfh3 (and phosphoinositide) biology that are invisible to contemporary haploid-centric cell biological, proteomic, and functional genomics approaches.

59 BASIC BIOLOGICAL SCIENCES↗

IMPROVING COSMOLOGICAL DISTANCE MEASUREMENTS USING TWIN TYPE IA SUPERNOVAE

We introduce a method for identifying “twin” Type Ia supernovae (SNe Ia) and using them to improve distance measurements. This novel approach to SN Ia standardization is made possible by spectrophotometric time series observations from the Nearby Supernova Factory (SNfactory). We begin with a well-measured set of SNe, find pairs whose spectra match well across the entire optical window, and then test whether this leads to a smaller dispersion in their absolute brightnesses. This analysis is completed in a blinded fashion, ensuring that decisions made in implementing the method do not inadvertently bias the result. We find that pairs of SNe with more closely matched spectra indeed have reduced brightness dispersion. We are able to standardize this initial set of SNfactory SNe to 0.083 ± 0.012 mag, implying a dispersion of 0.072 ± 0.010 mag in the absence of peculiar velocities. We estimate that with larger numbers of comparison SNe, e.g., using the final SNfactory spectrophotometric data set as a reference, this method will be capable of standardizing high-redshift SNe to within 0.06–0.07 mag. These results imply that at least 3/4 of the variance in Hubble residuals in current SN cosmology analyses is due to previously unaccounted-for astrophysical differences among the SNe.

79 ASTRONOMY AND ASTROPHYSICS↗

A flowing liquid lithium limiter for the Experimental Advanced Superconducting Tokamak

A program involving the extensive and systematic use of lithium (Li) as a “first,” or plasma-facing, surface in Tokamak fusion research devices located at Institute of Plasma Physics, Chinese Academy of Sciences, was started in 2009. Many remarkable results have been obtained by the application of Li coatings in Experimental Advanced Superconducting Tokamak (EAST) and liquid Li limiters in the HT-7 Tokamak—both located at the institute. In furtherance of the lithium program, a flowing liquid lithium (FLiLi) limiter system has been designed and manufactured for EAST. The design of the FLiLi limiter is based on the concept of a thin flowing film which was previously tested in HT-7. Exploiting the capabilities of the existing material and plasma evaluation system on EAST, the limiter will be pre-wetted with Li and mechanically translated to the edge of EAST during plasma discharges. The limiter will employ a novel electro-magnetic pump which is designed to drive liquid Li flow from a collector at the bottom of limiter into a distributor at its top, and thus supply a continuously flowing liquid Li film to the wetted plasma-facing surface. This paper focuses on the major design elements of the FLiLi limiter. In addition, a simulation of incoming heat flux has shown that the distribution of heat flux on the limiter surface is acceptable for a future test of power extraction on EAST.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Methods and preliminary measurement results of liquid Li wettability

A test of lithium wettability was performed in high vacuum (< 3 × 10{sup −4} Pa). High magnification images of Li droplets on stainless steel substrates were produced and processed using the MATLAB{sup ®} program to obtain clear image edge points. In contrast to the more standard “θ/2” or polynomial fitting methods, ellipse fitting of the complete Li droplet shape resulted in reliable contact angle measurements over a wide range of contact angles. Using the ellipse fitting method, it was observed that the contact angle of a liquid Li droplet on a stainless steel substrate gradually decreased with increasing substrate temperature. The critical wetting temperature of liquid Li on stainless steel was observed to be about 290 °C.

36 MATERIALS SCIENCE↗

Precision measurement of transverse velocity distribution of a strontium atomic beam

We measure the transverse velocity distribution in a thermal Sr atomic beam precisely by velocity-selective saturated fluorescence spectroscopy. The use of an ultrastable laser system and the narrow intercombination transition line of Sr atoms mean that the resolution of the measured velocity can reach 0.13 m/s, corresponding to 90 μK in energy units. The experimental results are in very good agreement with the results of theoretical calculations. Based on the spectroscopic techniques used here, the absolute frequency of the intercombination transition of {sup 88}Sr is measured using an optical-frequency comb generator referenced to the SI second through an H maser, and is given as 434 829 121 318(10) kHz.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Structure of AgI-doped Ge-In-S glasses: Experiment, reverse Monte Carlo modelling, and density functional calculations

We report an investigation of the structure and vibrational modes of Ge-In-S-AgI bulk glasses using X-ray diffraction, EXAFS spectroscopy, Reverse Monte-Carlo (RMC) modelling, Raman spectroscopy, and density functional theoretical (DFT) calculations. The combination of these techniques made it possible to elucidate the short- and medium-range structural order of these glasses. Data interpretation revealed that the AgI-free glass structure is composed of a network where GeS{sub 4/2} tetrahedra are linked with trigonal InS{sub 3/2} units; S{sub 3/2}Ge-GeS{sub 3/2} ethane-like species linked with InS{sub 4/2}{sup -} tetrahedra form sub-structures which are dispersed in the network structure. The addition of AgI into the Ge-In-S glassy matrix causes appreciable structural changes, enriching the Indium species with Iodine terminal atoms. The existence of trigonal species InS{sub 2/2}I and tetrahedral units InS{sub 3/2}I{sup -} and InS{sub 2/2}I{sub 2}{sup -} is compatible with the EXAFS and RMC analysis. Their vibrational properties (harmonic frequencies and Raman activities) calculated by DFT are in very good agreement with the experimental values determined by Raman spectroscopy. - Graphical abstract: Experiment (XRD, EXAFS, RMC, Raman scattering) and density functional calculations are employed to study the structure of AgI-doped Ge-In-S glasses. The role of mixed structural units as illustrated in the figure is elucidated. Highlights: Black-Right-Pointing-Pointer Doping Ge-In-S glasses with AgI causes significant changes in glass structure. Black-Right-Pointing-Pointer Experiment and DFT are combined to elucidate short- and medium-range structural order. Black-Right-Pointing-Pointer Indium atoms form both (InS{sub 4/2}){sup -} tetrahedra and InS{sub 3/2} planar triangles. Black-Right-Pointing-Pointer (InS{sub 4/2}){sup -} tetrahedra bond to (S{sub 3/2}Ge-GeS{sub 3/2}){sup 2+} ethane-like units forming neutral sub-structures. Black-Right-Pointing-Pointer Mixed chalcohalide species (InS{sub 3/2}I){sup -} offer vulnerable sites for the uptake of Ag{sup +}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SoftLab: A Soft-Computing Software for Experimental Research with Commercialization Aspects

SoftLab is a software environment for research and development in intelligent modeling/control using soft-computing paradigms such as fuzzy logic, neural networks, genetic algorithms, and genetic programs. SoftLab addresses the inadequacies of the existing soft-computing software by supporting comprehensive multidisciplinary functionalities from management tools to engineering systems. Furthermore, the built-in features help the user process/analyze information more efficiently by a friendly yet powerful interface, and will allow the user to specify user-specific processing modules, hence adding to the standard configuration of the software environment.

Akbarzadeh-T, M.-R.↗