Search NASA⌕ Search

Engineering topics

Ren, Zhongjing

Publications and source records attributed to Ren, Zhongjing.

Electrothermally Driven Reconfiguration of Microrobotic Beam Structures for the ChipSail System

Solar sailing enables efficient propellant-free attitude adjustment and orbital maneuvers of solar sail spacecraft with high area-to-mass ratios. However, the heavy supporting mass for large solar sails inevitably leads to low area-to-mass ratios. Inspired by chip-scale satellites, a chip-scale solar sail system named ChipSail, consisting of microrobotic solar sails and a chip-scale satellite, was proposed in this work. The structural design and reconfigurable mechanisms of an electrothermally driven microrobotic solar sail made of Al\Ni 50 Ti 50 bilayer beams were introduced, and the theoretical model of its electro-thermo-mechanical behaviors was established. The analytical solutions to the out-of-plane deformation of the solar sail structure appeared to be in good agreement with the finite element analysis (FEA) results. A representative prototype of such solar sail structures was fabricated on silicon wafers using surface and bulk microfabrication, followed by an in-situ experiment of its reconfigurable property under controlled electrothermal actuation. The experimental results demonstrated significant electro-thermo-mechanical deformation of such microrobotic bilayer solar sails, showing great potential in the development of the ChipSail system. Analytical solutions to the electro-thermo-mechanical model, as well as the fabrication process and characterization techniques, provided a rapid performance evaluation and optimization of such microrobotic bilayer solar sails for the ChipSail.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A helical actuator driven by biased SMA: design, model, and experiment

A helical actuator driven by biased shape memory alloy (SMA) patterns embedded into a soft composite ribbon base is presented in this work. Instead of common U-shape SMA wires, a single SMA wire is woven into planar patterns, which enable helical deformation of the composite ribbon from an initially flat geometry. An analytical static model is established for accurate and rapid prediction of the helical reconfiguration arising from the shape memory effect of woven SMA patterns, followed by validation of the static model using the finite element method (FEM). The finite element results are compared with the analytical solutions given by this static model, which show a high agreement. Parametric study of the influences of eight independent design variables on the dependent helical parameters, such as combined curvatures, pitches, and helical angles, is completed. It is found that the helically deformed geometry is mainly dominated by diameters, biased positions, inclined angles, and numbers of skewed segments of the SMA wire. Fabrication and in-situ experimental test of a prototype of such helical actuators qualitatively demonstrate its dramatic three-dimensional (3D) spiral reconfiguration from a two-dimensional (2D) flat ribbon. In conclusion, such SMA patterns will allow more diverse designs of soft actuators for a wider range of robotic applications.

36 MATERIALS SCIENCE↗

Smart material based multilayered microbeam structures for spatial self-deployment and reconfiguration: A residual stress approach

Alleviation of the potentially damaging effects induced by residual stresses was comprehensively investigated in previous research. Here, this paper, however, presents a spatially self-deployable and reconfigurable multilayered microbeam which takes advantage of residual stresses and shape memory effects. Reconfigurable mechanism of a typical four-layered microbeam composed of Pt\Ni 50 Ti 50 \Ni 50 Ti 50 \Pt is introduced, followed by analytical modeling of the maximum distance of the self-deployed gap as functions of variable structural and material parameters, including compressive residual stress in Pt layers and tensile residual stress in Ni 50 Ti 50 layers. Analytical solutions given by the static model agree well with the results obtained via finite element models (FEMs). Fabrication, characterization, and in-situ experiments were carried out to validate the feasibility of deployment of the as-released four-layered microbeam. The maximum distance of the gap was measured to be 41.39 μm at 20 °C, which could be increased to 51.73 μm thanks to controllable reconfiguration driven by shape memory effects. Theoretical analysis of such self-deployment and reconfiguration suggested a tensile residual stress increase by 52 MPa in Ni 50 Ti 50 layers. The multilayered microbeam structure with capabilities of self-deployment and reconfiguration offers great potential for various emerging applications, such as micro robotics, medical drug delivery devices, and intelligent chip scale spacecraft.

36 MATERIALS SCIENCE↗

Design, modeling and experimental validation of a micro cantilever beam with an electro-controllable twisting ability

The structure design of micro cantilever beams (MCBs), which has a significant effect on MCBs' controllable actuation range, is usually restricted by the establishment of the inner electric circuit. This paper proposes the design of a micro electro-controllable twisting cantilever beam (METCB). The architecture and the fabrication diagram of the proposed METCB are presented before its features are theoretically and experimentally validated. In detail, the analytical validation includes a sequence of two models: electro-thermal and thermo-mechanical. Through these two models, the thermal distribution along the METCB and the deformation brought by the thermal distribution are investigated, respectively. On the basis of the design and equations, the METCB samples have been manufactured using a planar deposition technique with an e-beam evaporator. Two in-site experiments are then conducted to sequentially figure out the upper voltage limit of the inner electric circuit and the maximum temperature limit of the METCB. Finally, another experiment is carried out to explore the relation between the applied voltage and the relative twisting angle of the METCB sample. Here, the theoretical prediction and the observed experiment result both prove the feasibility of the proposed METCB and its electro-controllable twisting ability.

36 MATERIALS SCIENCE↗

Current divisions and distributed Joule heating of two-dimensional grid microstructures

This work presents current divisions and distributed Joule heating of two-dimensional (2D) grid microstructures. The current divisions on 2×2, 4×4, and n×n grid microstructures made of the same conductive beams are analyzed theoretically, and Kirchhoff's voltage law (KVL) and Kirchhoff's current law (KCL) are employed to determine the current division factors and directions under different voltage input cases. The equivalent resistances and Joule heating power are therefore derived. 2D 2×2 grid microstructures made of gold (60 nm in thickness) and those made of near-equiatomic NiTi (850 nm in thickness) for various independent voltage input cases are fabricated by electron-beam evaporation and co-sputtering, respectively. The equivalent resistances of these grid microstructures are measured by four-terminal resistance measurement at ambient conditions, which show a good agreement with the theoretical results. Further investigation on the electrical resistivities of evaporated gold layer (4.85 × 10 -8 Ω ∙ m) and co-sputtered NiTi (1.23 × 10 -5 Ω ∙ m) reveals that the influences of scale effect and fabrication process on the resistivity cannot be neglected. As such, it is found to be necessary to consider the materials' resistivity in the fabricated grid microstructures before their electro-thermal analysis.

25 ENERGY STORAGE↗

Multilayered microstructures with shape memory effects for vertical deployment

This paper presents a fabrication and characterization of multilayered microstructures with shape memory effects enabling large vertical deployment under electro-thermal actuation. Our previous research demonstrated vertical deployment of such microstructures by the effect of thermal mismatch. Development of equiatomic NiTi layers in the multilayered microstructure is investigated further for shape memory effects. Multilayered microstructures are built by sputtered NiTi layers and a lift-off process. Negative photoresist ma-N1420 enables clean lift-off of 500 nm thick NiTi layers by forming a significant undercut profile after development. The parametric study on co-sputter powers for Ti and Ni 50 Ti 50 targets suggests that 100 W RF on Ti target and 200 W DC on Ni 50 Ti 50 target can deposit Ni 49.62 Ti 50.38 layers. X-Ray Diffraction (XRD) and Atomic Force Microscopy (AFM) were used to study the crystal structures and surface topography of NiTi layers. XRD results of post-annealed Ni 49.62 Ti 50.38 layers show coexistence of austenite and martensitic phases at room temperature, suggesting that the transformation temperature of such NiTi layers should be approximate 20 °C. The surface topography of Ni 49.62 Ti 50.38 layers reveals substantial increase of surface roughness at ambient conditions after the annealing. Experimental verification of the multilayered microstructure for vertical deployment was carried out by Signatone Probe Station and Dual Scanning Electron Microscope/Focused Ion Beam (SEM/FIB) system. Finally, a vertical deployment of the two-dimensional (2D) multilayered microstructures for three-dimensional (3D) can be detected by applying a constant voltage of 0.04 V, and the expected 3D deployment displacement is enlarged from 2 μm to 10 μm by introducing the shape memory effect.

42 ENGINEERING↗

Effects of deposition and annealing conditions on the crystallisation of NiTi thin films by e-beam evaporation

This Letter demonstrates the effects of deposition and annealing conditions on the crystallisation of nickel–titanium (NiTi) thin films deposited by the e-beam evaporation. NiTi thin films of 0.5 μm thick are fabricated on P-type (110) silicon substrates using the e-beam evaporation technique. We find that with the characterisations using the X-ray diffraction method, the results indicate that low e-beam deposition rate and argon employed annealing procedures can be beneficial to the formation of NiTi crystalline structure. Additionally, the as-deposited NiTi thin films without annealing procedures are amorphous, when deposited on the substrates at low temperatures. The differential scanning calorimetry studies show NiTi thin films formed by the e-beam evaporation are Ni-rich. Furthermore, SEM images illustrate that high-precision patterned NiTi thin film microstructures can be fabricated by combining with the e-beam evaporation and lift-off resist methods, without any wet or dry etching procedures. The proposed fabrication process for NiTi thin film microstructures shows great potential for application in shape memory alloy medical devices, as well as the micro-robotics.

36 MATERIALS SCIENCE↗